Click here

VEHICLE STABILITY CONTROL SYSTEM, Diagnostic DTC:C1432

Click here
Click here Click here
DTC Code DTC Name
C1432 Steering Angle Sensor Power Source Voltage Malfunction
Click here

DESCRIPTION

Steering sensor signals are sent to the skid control ECU (master cylinder solenoid) via the CAN communication system. When there is a malfunction in the CAN communication system, it is detected by the steering angle sensor zero point malfunction diagnostic function.

DTC Code DTC Detection Condition Trouble Area
C1432 A steering sensor power supply malfunction signal is received from the steering sensor.

  • ECU-B1 fuse

  • ECU-IG No. 2 fuse

  • Steering sensor power supply

  • Steering sensor

  • Steering control ECU (w/ VGRS)
Click here

WIRING DIAGRAM

Click here

INSPECTION PROCEDURE

Note:

  • When replacing the steering sensor, confirm that the replacement part is of the correct specification.

  • Inspect the fuses for circuits related to this system before performing the following inspection procedure.

Tip:

When the speed sensor or the yaw rate sensor assembly has trouble, DTCs for the steering sensor may be stored even when the steering sensor is normal. When DTCs for the speed sensor or yaw rate sensor assembly are output together with DTCs for the steering sensor, inspect and repair the speed sensor and yaw rate sensor assembly first, and then inspect and repair the steering sensor.

Click here

PROCEDURE


  1. Click here

    CHECK DTC (CAN COMMUNICATION SYSTEM)


    1. Check for DTCs (Click here).

      Table 1. Result
      Result Proceed to
      CAN DTC is not output A
      CAN DTC is output (for LHD) B
      CAN DTC is output (for LHD) C

  2. Click here

    CHECK HARNESS AND CONNECTOR (IG/ESS TERMINAL)


    1. Turn the ignition switch off.

    2. Make sure that there is no looseness in the locking part and connecting part of the connectors.

    3. A0159ILE12

      Disconnect the steering sensor connector.

    4. Measure the voltage according to the value(s) in the table below.

      Standard Voltage
      Tester Connection Switch Condition Specified Condition
      E11-1 (IG) - Body ground Ignition switch ON 11 to 14 V

    5. Measure the resistance according to the value(s) in the table below.

      Standard Resistance
      Tester Connection Condition Specified Condition
      E11-2 (ESS) - Body ground Always Below 1 Ω
      Table 2. Text in Illustration
      *a

      Front view of wire harness connector

      (to Steering Sensor)

  3. Click here

    CHECK HARNESS AND CONNECTOR (BAT TERMINAL)


    1. Turn the ignition switch off.

    2. A0159ILE13

      Disconnect the steering sensor connector.

    3. Measure the voltage according to the value(s) in the table below.

      Standard Voltage
      Tester Connection Condition Specified Condition
      E11-3 (BAT) - Body ground Always 11 to 14 V
      Table 3. Text in Illustration
      *a

      Front view of wire harness connector

      (to Steering Sensor)
      Table 4. Result
      Result Proceed to
      OK A
      NG (w/ VGRS) B
      NG (w/o VGRS) C

  4. Click here

    CHECK HARNESS AND CONNECTOR (+BI TERMINAL)


    1. Turn the ignition switch off.

    2. A0157PHE04

      Disconnect the steering control ECU connector.

    3. Measure the voltage according to the value(s) in the table below.

      Standard Voltage
      Tester Connection Condition Specified Condition
      E77-10 (+BI) - Body ground Always 11 to 14 V
      Table 5. Text in Illustration
      *a

      Front view of wire harness connector

      (to Steering Control ECU)

  5. Click here

    CHECK HARNESS AND CONNECTOR (STEERING SENSOR - STEERING CONTROL ECU)


    1. Turn the ignition switch off.

    2. Disconnect the E11 steering sensor connector.

    3. Disconnect the E79 steering control ECU connector.

    4. Measure the resistance according to the value(s) in the table below.

      Standard Resistance
      Tester Connection Condition Specified Condition
      E11-3 (BAT) - E79-1 (+BO) Always Below 1 Ω
      E11-3 (BAT) - Body ground Always 10 kΩ or higher
      Table 6. Result
      Result Proceed to
      NG A
      OK (for LHD) B
      OK (for RHD) C

  6. Click here

    REPLACE STEERING SENSORClick here

  7. Click here

    REPAIR OR REPLACE HARNESS OR CONNECTOR

  8. Click here

    GO TO CAN COMMUNICATION SYSTEM (HOW TO PROCEED WITH TROUBLESHOOTING)Click here

  9. Click here

    REPLACE STEERING CONTROL ECUClick here

  10. Click here

    GO TO CAN COMMUNICATION SYSTEM (HOW TO PROCEED WITH TROUBLESHOOTING)Click here

  11. Click here

    REPLACE STEERING CONTROL ECUClick here