FRONT STABILIZER BAR (w/o KDSS) INSTALLATION


  1. INSTALL NO. 1 FRONT STABILIZER BAR BUSH


    1. A015B9ZE01

      Install the 2 bushes to the outer side of the bush stoppers on the front stabilizer bar as shown in the illustration.

      Note

      Be sure to install the front No. 1 stabilizer bar bushes so that the cut and bump of each bush faces the under of the vehicle.

  2. INSTALL FRONT STABILIZER BAR


    1. A0155ZLE01

      Set the stabilizer bracket so that the arrow mark is facing the front side of the vehicle.

    2. A01596I

      Temporarily install the 2 stabilizer brackets and front stabilizer bar with the 4 bolts.

  3. TEMPORARILY INSTALL FRONT STABILIZER LINK ASSEMBLY LH


    1. Temporarily install the stabilizer link with the nut and bolt.

    2. A0159ZXE01

      Tighten the nut.

      Torque:
      128 N*m  { 1305 kgf*cm, 94 ft.*lbf }

  4. TEMPORARILY INSTALL FRONT STABILIZER LINK ASSEMBLY RH


    1. A015A7WE01

      Temporarily install the stabilizer link with the nut and bolt.

    2. Tighten the nut.

      Torque:
      128 N*m  { 1305 kgf*cm, 94 ft.*lbf }

  5. TIGHTEN NO. 1 FRONT STABILIZER BRACKET LH


    1. A0158MNE01

      Tighten the 2 bolts.

      Torque:
      87 N*m  { 887 kgf*cm, 64 ft.*lbf }

      Note

      Tighten the bolts in 3 steps, in the order shown in the illustration.

  6. TIGHTEN NO. 1 FRONT STABILIZER BRACKET RH


    1. A015BMPE01

      Tighten the 2 bolts.

      Torque:
      87 N*m  { 887 kgf*cm, 64 ft.*lbf }

      Note

      Tighten the bolts in 3 steps, in the order shown in the illustration.

  7. INSTALL NO. 1 ENGINE UNDER COVER SUB-ASSEMBLY


    1. Install the No. 1 engine under cover sub-assembly with the 10 bolts.

      Torque:
      29 N*m  { 296 kgf*cm, 21 ft.*lbf }

  8. INSTALL FRONT FENDER SPLASH SHIELD SUB-ASSEMBLY LH


    1. Push in the clip to install the front fender splash shield sub-assembly LH.

    2. Install the 3 bolts and screw.

  9. INSTALL FRONT FENDER SPLASH SHIELD SUB-ASSEMBLY RH


    1. Push in the clip to install the front fender splash shield sub-assembly RH.

    2. Install the 3 bolts and 2 screws.

  10. STABILIZE SUSPENSION


    1. Install the front wheels.

      Torque:
      for aluminum wheel
      131 N*m  { 1336 kgf*cm, 97 ft.*lbf }
      for steel wheel
      209 N*m  { 2131 kgf*cm, 154 ft.*lbf }

    2. Lower the vehicle.

    3. Press down on the vehicle several times to stabilize the suspension.

  11. TIGHTEN FRONT STABILIZER LINK ASSEMBLY LH


    1. A015A7UE01

      Tighten the bolt.

      Torque:
      135 N*m  { 1376 kgf*cm, 100 ft.*lbf }

      Note

      Perform this procedure with all 4 wheels on the ground.

  12. TIGHTEN FRONT STABILIZER LINK ASSEMBLY RH


    1. A01567AE01

      Tighten the bolt.

      Torque:
      135 N*m  { 1376 kgf*cm, 100 ft.*lbf }

      Note

      Perform this procedure with all 4 wheels on the ground.