Click here

FRONT ACCELERATION SENSOR REMOVAL

Click here
Click here Click here
  1. Click here

    TABLE OF BOLT, SCREW AND NUT

    Tip:

    All bolts, screws and nuts relevant to installing and removing the instrument panel are shown along with their alphabet code in the table below.

  2. Click here

    DISCONNECT CABLE FROM NEGATIVE BATTERY TERMINAL

    Note:

    When disconnecting the cable, some systems need to be initialized after the cable is reconnected (Click here).

  3. Click here

    REMOVE NO. 2 INSTRUMENT PANEL FINISH PANEL CUSHION


    1. A015BCWE02

      Place protective tape as shown in the illustration.

    2. Using a moulding remover, detach the 7 claws and remove the panel cushion.

  4. Click here

    REMOVE LOWER INSTRUMENT PANEL PAD SUB-ASSEMBLY LH


    1. A015D40

      Remove the clip.

    2. Remove the screw.

    3. Detach the 8 claws.

    4. Remove the panel pad and disconnect the connectors and 2 clamps.

  5. Click here

    REMOVE NO. 1 INSTRUMENT PANEL FINISH PANEL CUSHION


    1. Put protective tape around the No. 1 instrument panel finish panel cushion.

      Table 1. Text in Illustration
      *1 Protective Tape

    2. Using a moulding remover, detach the 7 claws and remove the No. 1 instrument panel finish panel cushion.

  6. Click here

    REMOVE LOWER INSTRUMENT PANEL PAD SUB-ASSEMBLY RH


    1. Remove the clip and screw.

    2. Detach the 7 claws and remove the lower instrument panel pad sub-assembly.

  7. Click here

    REMOVE LOWER CENTER INSTRUMENT CLUSTER FINISH PANEL SUB-ASSEMBLY


    1. Detach the 7 claws.

    2. Disconnect the connectors and remove the lower center instrument cluster finish panel sub-assembly.

  8. Click here

    REMOVE INSTRUMENT SIDE PANEL LH


    1. Place protective tape as shown in the illustration.

      Table 2. Text in Illustration
      *1 Protective Tape

    2. Using a moulding remover, detach the 6 claws and remove the instrument side panel.

  9. Click here

    REMOVE NO. 1 INSTRUMENT CLUSTER FINISH PANEL GARNISH


    1. Place protective tape as shown in the illustration.

      Table 3. Text in Illustration
      *1 Protective Tape

    2. Using a moulding remover, detach the 3 claws and remove the No. 1 instrument cluster finish panel garnish.

  10. Click here

    REMOVE NO. 2 INSTRUMENT CLUSTER FINISH PANEL GARNISH


    1. Place protective tape as shown in the illustration.

    2. A0159Y8E01

      Using a moulding remover, detach the 2 claws and remove the No. 2 instrument cluster finish panel garnish.

      Table 4. Text in Illustration
      *A w/ Entry and Start System *B w/o Entry and Start System
      *1 Protective Tape - -
  11. Click here

    REMOVE NO. 1 INSTRUMENT PANEL UNDER COVER SUB-ASSEMBLY (w/ Floor Under Cover)


    1. Remove the 2 screws.

    2. Detach the 3 claws.

    3. Disconnect the connectors and remove the No. 1 instrument panel under cover.

  12. Click here

    REMOVE FRONT DOOR SCUFF PLATE LH


    1. Detach the 7 claws and 4 clips, and remove the scuff plate.

  13. Click here

    REMOVE COWL SIDE TRIM BOARD LH


    1. Remove the cap nut.

    2. Detach the 2 clips and remove the cowl side trim board.

  14. Click here

    REMOVE LOWER NO. 1 INSTRUMENT PANEL FINISH PANEL


    1. Using a screwdriver, detach the 2 claws and open the hole cover.

      Tip:

      Tape the screwdriver tip before use.

      Table 5. Text in Illustration
      *1 Protective Tape

    2. w/ Driver Side Knee Airbag:


      1. Remove the 2 bolts.

      2. A015CUJ

        Detach the 16 claws.

    3. w/o Driver Side Knee Airbag:


      1. Remove the 2 bolts.

      2. A015A9A

        Detach the 9 claws.

    4. A0158MF

      for Automatic Air Conditioning System:


      1. Detach the 2 claws and remove the room temperature sensor.

    5. A0156SA

      Detach the 2 claws and disconnect the 2 control cables.

    6. Disconnect the connectors and remove the lower No. 1 instrument panel finish panel.

  15. Click here

    REMOVE NO. 1 SWITCH HOLE BASE


    1. Detach the 4 claws.

    2. Disconnect the connectors and remove the No. 1 switch hole cover.

  16. Click here

    REMOVE DRIVER SIDE KNEE AIRBAG ASSEMBLY (w/ Driver Side Knee Airbag)


    1. A015A6DE01

      Remove the 5 bolts and driver side knee airbag.

    2. Disconnect the connector.

      Note:

      When handling the airbag connector, take care not to damage the airbag wire harness.

  17. Click here

    REMOVE LOWER INSTRUMENT PANEL SUB-ASSEMBLY (w/o Driver Side Knee Airbag)


    1. Detach the 2 claws and disconnect the DLC3.

    2. Remove the 5 bolts and lower instrument panel.

  18. Click here

    REMOVE INSTRUMENT SIDE PANEL RH (w/o Airbag Cut Off Switch)


    1. Place protective tape as shown in the illustration.

      Table 6. Text in Illustration
      *1 Protective Tape

    2. Using a moulding remover, detach the 6 claws and remove the instrument side panel.

  19. Click here

    REMOVE INSTRUMENT SIDE PANEL RH (w/ Airbag Cut Off Switch)


    1. Place protective tape as shown in the illustration.

      Table 7. Text in Illustration
      *1 Protective Tape

    2. Using a moulding remover, detach the 6 claws.

    3. Disconnect the connector and remove the instrument side panel.

  20. Click here

    REMOVE FRONT DOOR SCUFF PLATE RH

    Tip:

    Use the same procedures described for the LH side.

  21. Click here

    REMOVE NO. 2 INSTRUMENT PANEL UNDER COVER SUB-ASSEMBLY (w/ Floor Under Cover)


    1. Detach the 4 claws and remove the No. 2 instrument panel under cover.

  22. Click here

    REMOVE COWL SIDE TRIM BOARD RH


    1. Remove the cap nut.

    2. Detach the 2 clips and remove the cowl side trim board.

  23. Click here

    REMOVE FRONT PASSENGER SIDE KNEE AIRBAG ASSEMBLY (w/ Passenger Side Knee Airbag)


    1. A01598PE01

      Remove the 4 bolts.

    2. Detach the 4 claws and remove the front passenger side knee airbag.

    3. Disconnect the connector.

      Note:

      When handling the airbag connector, take care not to damage the airbag wire harness.

  24. Click here

    REMOVE LOWER INSTRUMENT PANEL (w/o Passenger Side Knee Airbag)


    1. Remove the 2 bolts.

    2. Detach the 4 claws and remove the lower instrument panel.

  25. Click here

    REMOVE NO. 3 INSTRUMENT CLUSTER FINISH PANEL GARNISH


    1. Place protective tape as shown in the illustration.

      Table 8. Text in Illustration
      *1 Protective Tape

    2. Using a moulding remover, detach the 6 claws and remove the No. 3 instrument cluster finish panel garnish.

  26. Click here

    REMOVE INSTRUMENT PANEL BOX DOOR KNOB


    1. Using a moulding remover, detach the 2 claws and remove the instrument panel box door knob.

  27. Click here

    REMOVE LOWER NO. 2 INSTRUMENT PANEL FINISH PANEL


    1. Remove the 4 bolts.

    2. Detach the 3 claws.

    3. Disconnect the connector and remove the lower No. 2 instrument panel finish panel.

  28. Click here

    REMOVE STEERING CONTROL ECU WITH JUNCTION BLOCK (for LHD)


    1. A015635E01

      Vehicle rear side:


      1. Disconnect the 7 connectors.

      2. Detach the 2 clamps.

      3. Remove the bolt and 2 nuts.

    2. Vehicle front side:


      1. Disconnect the 5 connectors.

    3. Remove the steering control ECU with junction block from the vehicle.

  29. Click here

    REMOVE STEERING CONTROL ECU WITH JUNCTION BLOCK (for RHD)


    1. A01563HE01

      Vehicle rear side:


      1. Disconnect the 2 connectors.

      2. Remove the bolt and 2 nuts.

    2. Vehicle front side:


      1. Disconnect the connector.

    3. Remove the steering control ECU with junction block from the vehicle.

  30. Click here

    REMOVE ACCELERATION SENSOR (for Driver Side)


    1. A015A33

      Disconnect the connector.

    2. Remove the bolt and sensor.

      Tip:

      Use the same procedures for LHD and RHD vehicles.

  31. Click here

    REMOVE ACCELERATION SENSOR (for Front Passenger Side)


    1. A015AXA

      Disconnect the connector.

    2. Remove the bolt and sensor.

      Tip:

      Use the same procedures for LHD and RHD vehicles.