FRONT DRIVE SHAFT ASSEMBLY INSTALLATION


  1. INSTALL FRONT DRIVE SHAFT ASSEMBLY LH


    1. Coat the lip of the differential oil seal with MP grease.

      Tech Tips

      Inspect the oil seal for wear or damage.

    2. Coat the spline of the inboard joint shaft assembly with hypoid gear oil.

    3. A01577T

      Align the shaft splines and install the drive shaft with a brass bar and hammer.

      Note


      • Set the snap ring with the opening side facing downward.

      • Be careful not to damage the oil seal.

      • If the outboard joint shaft is new, remove the anti-rust oil on the screw end with non-residue solvent.

      Tech Tips

      Whether the inboard joint shaft is in contact with the pinion shaft or not can be confirmed from the sound or feeling when tapping in the shaft.

  2. INSTALL FRONT AXLE ASSEMBLY LH

    Click here

  3. ADD DIFFERENTIAL OIL


    1. A015750E27

      Add differential oil so that the oil level is between 0 to 5 mm (0 to 0.197 in.) from the bottom lip of the differential filler plug hole.

      Note


      • Too much or too little oil will lead to differential problems.

      • After changing the oil, drive the vehicle and then check the oil level again.

      Front differential oil type and viscosity
      Toyota Genuine Differential gear oil LT 75W-85 GL-5 or equivalent
      Rear Differential Oil Type and Viscosity
      Item Oil Type and Viscosity
      w/o LSD Toyota Genuine Differential gear oil LT 75W-85 GL-5 or equivalent
      w/ LSD Toyota Genuine Differential gear oil LX 75W-85 GL-5 or equivalent
      Front differential capacity
      1.85 to 1.95 liters (1.96 to 2.06 US qts., 1.63 to 1.71 Imp. qts.)
      Rear Differential Capacity
      Item Specified Condition
      Standard 4.15 to 4.25 liters (4.39 to 4.49 US qts., 3.66 to 3.74 Imp. qts.)
      w/ LSD 4.10 to 4.20 liters (4.34 to 4.43 US qts., 3.60 to 3.69 Imp. qts.)
      w/ Differential lock

    2. for Front Differential:


      1. Using a 10 mm hexagon wrench, install a new gasket and the filler plug.

        Torque:
        39 N*m  { 400 kgf*cm, 29 ft.*lbf }

      2. Install the engine under cover.

    3. for Rear Differential:


      1. Install a new gasket and the filler plug.

        Torque:
        49 N*m  { 500 kgf*cm, 36 ft.*lbf }

  4. INSTALL FRONT FENDER SPLASH SHIELD SUB-ASSEMBLY LH


    1. Push in the clip to install the front fender splash shield sub-assembly LH.

    2. Install the 3 bolts and screw.

  5. INSTALL FRONT FENDER SPLASH SHIELD SUB-ASSEMBLY RH


    1. Push in the clip to install the front fender splash shield sub-assembly RH.

    2. Install the 3 bolts and 2 screws.

  6. INSTALL NO. 2 ENGINE UNDER COVER


    1. Install the No. 2 engine under cover with the 2 bolts.

      Torque:
      29 N*m  { 296 kgf*cm, 21 ft.*lbf }

  7. INSTALL NO. 1 ENGINE UNDER COVER SUB-ASSEMBLY


    1. Install the No. 1 engine under cover with the 10 bolts.

      Torque:
      29 N*m  { 296 kgf*cm, 21 ft.*lbf }