CLUTCH MASTER CYLINDER (for LHD) REMOVAL


  1. DRAIN CLUTCH FLUID

  2. REMOVE NO. 2 INSTRUMENT PANEL FINISH PANEL CUSHION

    A015940E01
    Text in Illustration
    *1 Protective Tape

    1. Put protective tape around the No. 2 instrument panel finish panel cushion.

    2. Using a moulding remover, detach the 7 claws and remove the No. 2 instrument panel finish panel cushion.

  3. REMOVE LOWER INSTRUMENT PANEL PAD SUB-ASSEMBLY LH

    A015BUX

    1. Remove the clip and screw.

    2. Detach the 8 claws.

    3. Disconnect the connectors, detach the 2 clamps and remove the lower instrument panel pad sub-assembly.

  4. REMOVE INSTRUMENT SIDE PANEL LH

    A0155UDE06
    Text in Illustration
    *1 Protective Tape

    1. Place protective tape as shown in the illustration.

    2. Using a moulding remover, detach the 6 claws and remove the instrument side panel.

  5. REMOVE NO. 1 INSTRUMENT CLUSTER FINISH PANEL GARNISH

    A0156ALE04
    Text in Illustration
    *1 Protective Tape

    1. Place protective tape as shown in the illustration.

    2. Using a moulding remover, detach the 3 claws and remove the No. 1 instrument cluster finish panel garnish.

  6. REMOVE NO. 2 INSTRUMENT CLUSTER FINISH PANEL GARNISH


    1. Place protective tape as shown in the illustration.

    2. Using a moulding remover, detach the 2 claws and remove the No. 2 instrument cluster finish panel garnish.

      A0159Y8E01
      Text in Illustration
      *A w/ Entry and Start System *B w/o Entry and Start System
      *1 Protective Tape - -

  7. REMOVE FRONT DOOR SCUFF PLATE LH

    A0157IK

    1. Detach the 7 claws and 4 clips, and remove the scuff plate.

  8. REMOVE NO. 1 INSTRUMENT PANEL UNDER COVER SUB-ASSEMBLY (w/ Floor Under Cover)

    A0159IW

    1. Remove the 2 screws.

    2. Detach the 3 claws.

    3. Disconnect the connectors and remove the No. 1 instrument panel under cover.

  9. REMOVE COWL SIDE TRIM BOARD LH

    A0156SP

    1. Remove the cap nut.

    2. Detach the 2 clips and remove the cowl side trim board.

  10. REMOVE LOWER NO. 1 INSTRUMENT PANEL FINISH PANEL

    A015825

    1. Remove the 4 bolts.

    2. Detach the 3 claws.

    3. Disconnect the connector and remove the lower No. 2 instrument panel finish panel.

  11. REMOVE NO. 1 SWITCH HOLE BASE

    A015DE6

    1. Detach the 4 claws.

    2. Disconnect the connectors and remove the No. 1 switch hole cover.

  12. REMOVE DRIVER SIDE KNEE AIRBAG ASSEMBLY (w/ Driver Side Knee Airbag)


    1. A015A6DE01

      Remove the 5 bolts and driver side knee airbag.

    2. Disconnect the connector.

      Note

      When handling the airbag connector, take care not to damage the airbag wire harness.

  13. REMOVE LOWER INSTRUMENT PANEL SUB-ASSEMBLY (w/o Driver Side Knee Airbag)

    A0158Q7

    1. Detach the 2 claws and disconnect the DLC3.

    2. Remove the 5 bolts and lower instrument panel.

  14. REMOVE MAIN BODY ECU (COWL SIDE JUNCTION BLOCK LH)


    1. A015CNL

      Remove the 3 bolts.

    2. A015D8H

      Disconnect the 9 ECU connectors and remove the ECU.

  15. DISCONNECT CLUTCH MASTER CYLINDER TO FLEXIBLE HOSE TUBE AND CLUTCH RESERVOIR TUBE

    A015CZG

    1. Using a union nut wrench, disconnect the flexible hose tube.

      Tech Tips

      Use a container to catch the fluid.

    2. Disconnect the clutch reservoir tube.

  16. REMOVE CLUTCH PEDAL SUPPORT ASSEMBLY WITH CLUTCH MASTER CYLINDER


    1. Disconnect the clutch start switch connector.

    2. w/ Cruise Control System:

      Disconnect the clutch switch connector.

    3. A0155JR

      Remove the 2 nuts, bolt and clutch pedal support with clutch master cylinder.

  17. REMOVE CLUTCH RESERVOIR HOSE

    A015DY7

    1. Using pliers, grip the claws of the clip, slide the 2 clips and remove the clutch reservoir hose.

      Tech Tips

      Use a container to catch the fluid.

  18. REMOVE CLUTCH MASTER CYLINDER TO WAY TUBE

    A01566N

    1. Using a union nut wrench, remove the tube.

      Tech Tips

      Use a container to catch the fluid.

  19. REMOVE CLUTCH START SWITCH ASSEMBLY


    1. A01556P

      Remove the 2 nuts and clutch start switch.

  20. REMOVE CLUTCH MASTER CYLINDER ASSEMBLY


    1. A015C4F

      Remove the clip, wave washer and clevis pin.

    2. A0156O3

      Remove the 2 bolts and clutch master cylinder.