EXHAUST MANIFOLD REMOVAL


  1. REMOVE FRONT FENDER SPLASH SHIELD SUB-ASSEMBLY LH


    1. A01588F

      Remove the 3 bolts and screw.

    2. Turn the clip indicated by the arrow in the illustration to remove the front fender splash shield sub-assembly LH.

  2. REMOVE FRONT FENDER SPLASH SHIELD SUB-ASSEMBLY RH


    1. A0159SG

      Remove the 3 bolts and 2 screws.

    2. Turn the clip indicated by the arrow in the illustration to remove the front fender splash shield sub-assembly RH.

  3. REMOVE NO. 1 ENGINE UNDER COVER SUB-ASSEMBLY


    1. A015CCZ

      Remove the 10 bolts and No. 1 engine under cover.

  4. REMOVE NO. 2 ENGINE UNDER COVER


    1. A015A78

      Remove the 2 bolts and No. 2 engine under cover.

  5. REMOVE FRONT FENDER APRON SEAL FRONT RH


    1. A015AN4

      Using a clip remover, remove the 3 clips and fender apron seal.

  6. REMOVE FRONT FENDER APRON SEAL REAR RH


    1. A015D4I

      Using a clip remover, remove the 4 clips and fender apron seal.

  7. REMOVE FRONT FENDER APRON SEAL LH


    1. A015CC0

      Using a clip remover, remove the 3 clips and fender apron seal.

  8. REMOVE FRONT FENDER APRON SEAL REAR LH


    1. A0155AV

      Using a clip remover, remove the 4 clips and fender apron seal.

  9. REMOVE ENGINE OIL LEVEL DIPSTICK GUIDE


    1. Apply a light coat of engine oil to a new O-ring.

    2. Install the O-ring to the guide.

    3. Install the dipstick guide with the bolt.

      Torque:
      10 N*m  { 102 kgf*cm, 7 ft.*lbf }

    4. Install the dipstick.

    5. Connect the wire harness clamp.

  10. REMOVE TAILPIPE ASSEMBLY


    1. Remove the bolt, clamp and gasket.

    2. Remove the tailpipe from the 2 exhaust pipe supports.

    3. Remove the bolt and clamp, and then disconnect the tailpipe from the center exhaust pipe.

  11. REMOVE CENTER EXHAUST PIPE ASSEMBLY


    1. Remove the 4 bolts.

    2. Remove the center exhaust pipe from the 3 exhaust pipe supports.

    3. Remove the 2 gaskets from the front exhaust pipe and front No. 2 exhaust pipe.

  12. REMOVE FRONT NO. 2 EXHAUST PIPE ASSEMBLY


    1. Disconnect the heated oxygen sensor connector.

    2. Remove the bolt and disconnect the wire harness clamp bracket of the oxygen sensor from the transmission.

    3. Remove the 2 nuts, front No. 2 exhaust pipe and gasket from the exhaust manifold LH.

  13. REMOVE FRONT EXHAUST PIPE ASSEMBLY


    1. Disconnect the heated oxygen sensor connector.

    2. Remove the bolt and disconnect the wire harness clamp bracket of the oxygen sensor from the transmission.

    3. Remove the 2 nuts, front exhaust pipe and gasket from the exhaust manifold RH.

  14. REMOVE PROPELLER SHAFT HEAT INSULATOR


    1. A015BHU

      Remove the 2 bolts and heat insulator.

  15. REMOVE NO. 2 MANIFOLD STAY


    1. A0159NE

      Remove the 3 bolts and manifold stay.

  16. REMOVE NO. 2 EXHAUST MANIFOLD HEAT INSULATOR


    1. A0159EO

      Remove the 3 bolts and heat insulator.

  17. REMOVE EXHAUST MANIFOLD SUB-ASSEMBLY LH


    1. A0159W3

      Remove the 8 nuts, exhaust manifold and gasket.

  18. REMOVE NO. 1 MANIFOLD STAY


    1. A015C7Z

      Remove the 3 bolts and manifold stay.

  19. REMOVE NO. 1 EXHAUST MANIFOLD HEAT INSULATOR


    1. A015E1B

      Remove the 3 bolts and heat insulator.

  20. REMOVE EXHAUST MANIFOLD SUB-ASSEMBLY RH


    1. A0156VS

      Remove the 8 nuts, exhaust manifold and gasket.