Click here

EXHAUST PIPE INSTALLATION

Click here
Click here Click here
  1. Click here

    INSTALL FRONT EXHAUST PIPE ASSEMBLY


    1. Install a new gasket and the front exhaust pipe to the exhaust manifold with the 2 nuts.

      54 N*m 554 kgf*cm 40 ft.*lbf
  2. Click here

    INSTALL FRONT NO. 2 EXHAUST PIPE ASSEMBLY


    1. Install a new gasket and the front No. 2 exhaust pipe to the exhaust manifold LH with the 2 nuts.

      54 N*m 554 kgf*cm 40 ft.*lbf
  3. Click here

    INSTALL CENTER EXHAUST PIPE ASSEMBLY


    1. Install 2 new gaskets to the center exhaust pipe.

    2. Connect the center exhaust pipe to the 3 exhaust pipe supports.

    3. Install the center exhaust pipe with the 4 bolts.

      48 N*m 489 kgf*cm 35 ft.*lbf
  4. Click here

    INSTALL EXHAUST PIPE DAMPER


    1. Install the exhaust pipe damper and No. 4 exhaust pipe upper protector with the 2 bolts.

      19 N*m 194 kgf*cm 14 ft.*lbf
  5. Click here

    INSTALL TAILPIPE ASSEMBLY


    1. Install a new gasket to the center exhaust pipe.

    2. Install the tailpipe to the 2 exhaust pipe supports.

    3. A015A7YE01

      Install a new clamp.

      32 N*m 326 kgf*cm 24 ft.*lbf
      Table 1. Text in Illustration
      *a Top
      *b LH Side
      Tip:

      Install the clamp within the angle range shown in the illustration.

  6. Click here

    INSTALL HEATED OXYGEN SENSOR (for Bank 1 Sensor 2)


    1. Temporarily install the sensor to the front No. 2 exhaust pipe by hand.

    2. A015E1DE01

      Using SST, tighten the heated oxygen sensor.

      09224-00010
      without SST
      44 N*m 449 kgf*cm 32 ft.*lbf
      with SST
      40 N*m 408 kgf*cm 30 ft.*lbf
      Table 2. Text in Illustration
      *1 Fulcrum Length
      Tip:

      • Use a torque wrench with a fulcrum length of 300 mm (11.8 in.). When using a torque wrench with a fulcrum length that is not 300 mm (11.8 in.), calculate the torque specification for the torque wrench and SST based on the "without SST" torque specification (Click here).

      • Make sure SST and the wrench are connected in a straight line.

    3. Connect the heated oxygen sensor connector.

  7. Click here

    INSTALL HEATED OXYGEN SENSOR (for Bank 2 Sensor 2)


    1. Temporarily install the sensor to the front exhaust pipe by hand.

    2. A015D6KE01

      Using SST, tighten the heated oxygen sensor.

      09224-00010
      without SST
      44 N*m 449 kgf*cm 32 ft.*lbf
      with SST
      40 N*m 408 kgf*cm 30 ft.*lbf
      Table 3. Text in Illustration
      *1 Fulcrum Length
      Tip:

      • Use a torque wrench with a fulcrum length of 300 mm (11.8 in.). When using a torque wrench with a fulcrum length that is not 300 mm (11.8 in.), calculate the torque specification for the torque wrench and SST based on the "without SST" torque specification (Click here).

      • Make sure SST and the wrench are connected in a straight line.

    3. Attach the clamp and connect the heated oxygen sensor connector.

  8. Click here

    INSTALL PROPELLER SHAFT HEAT INSULATOR


    1. A0156MY

      Install the insulator with the 2 bolts.

      16 N*m 160 kgf*cm 12 ft.*lbf
  9. Click here

    INSPECT FOR EXHAUST GAS LEAK

    If gas is leaking, tighten the areas necessary to stop the leak. Replace damaged parts as necessary.