Click here

REAR NO. 1 SEAT INNER BELT ASSEMBLY (for 60/40 Split Seat Type 60 Side) INSTALLATION

Click here
Click here Click here
Tip:

  • Use the same procedures for the LHD and RHD.

  • The procedures listed below are for the LHD.

  • A bolt without a torque specification is shown in the standard bolt chart (Click here).

Click here
  1. Click here

    CONNECT NO. 1 SEAT 3 POINT TYPE BELT ASSEMBLY LH


    1. Connect the belt anchor.

      Note:

      Do not overlap the anchor part of the seat belt and protruding parts of the vehicle body.

  2. Click here

    INSTALL REAR NO. 1 SEAT INNER BELT ASSEMBLY LH


    1. Install the belt with the bolt.

      42 N*m 428 kgf*cm 31 ft.*lbf
      Note:

      Do not overlap the anchor part of the seat belt and protruding parts of the vehicle body.

      Tip:

      The No. 1 seat 3 point type belt anchor is fixed with the same bolt as the rear No. 1 seat inner belt LH. Therefore, connect it when installing the rear No. 1 seat inner belt LH.

  3. Click here

    INSTALL REAR SEAT UNDER TRAY COVER LH


    1. Attach the 4 claws to install the cover.

    2. Install the 2 screws.

  4. Click here

    INSTALL REAR SEAT CUSHION COVER RH


    1. Attach the 2 claws to install the cover.

    2. Install the 4 screws.

  5. Click here

    INSTALL REAR UNDER SIDE COVER LH


    1. Attach the 2 claws and 2 clips to install the cover.

    2. Install the 5 screws.

    3. A0155YN

      Attach the 10 claws.

  6. Click here

    INSTALL REAR SEATBACK STAY COVER LH


    1. Attach the 2 claws to install the cover.

    2. Install the screw.

  7. Click here

    INSTALL SEAT BELT ANCHOR COVER CAP


    1. A0159WX

      Install the anchor cover cap with the screw.

    2. A015C6J

      Attach the claw to close the cap.

  8. Click here

    INSTALL REAR NO. 1 SEAT HINGE SUB-ASSEMBLY RH


    1. Install the hinge with the 2 nuts.

      42 N*m 428 kgf*cm 31 ft.*lbf
  9. Click here

    INSTALL REAR NO. 1 SEAT HINGE SUB-ASSEMBLY LH


    1. A0155TF

      Attach the cable clamp to connect the cable.

    2. A0157X7

      Install the hinge with the 2 nuts.

      42 N*m 428 kgf*cm 31 ft.*lbf

    3. w/ Rear Seat Side Airbag:

      Attach the wire harness clamp.

    4. w/ Seat Heater System:

      Attach the wire harness clamp.

  10. Click here

    INSTALL REAR NO. 2 SEAT PROTECTOR


    1. Install the wire harness, and attach 2 claws to close the protector.

    2. A015BO6

      Attach the claw to install the protector to the seat hinge.

    3. Install the clip.

    4. A0155UV

      w/ Rear Seat Side Airbag:

      Attach the claw to install the wire harness connector.

    5. w/ Seat Heater System:

      Attach the claw to install the wire harness connector.

  11. Click here

    INSTALL REAR NO. 2 SEAT LEG SIDE COVER


    1. A015AUN

      Pass the fold seat stopper band through the seat leg side cover and attach it to the seat cushion frame with the bolt.

    2. A0156BB

      Attach the 4 claws to install the seat leg side cover.

    3. Install the 4 screws.

  12. Click here

    INSTALL UPPER SEAT TRACK RAIL COVER RH


    1. Attach the 2 claws to install the cover.

  13. Click here

    INSTALL UPPER SEAT TRACK RAIL COVER LH


    1. Attach the 2 claws to install the cover.

  14. Click here

    INSTALL REAR NO. 1 SEAT RECLINING COVER RH


    1. Attach the 4 claws to install the cover.

    2. Install the 2 screws.

  15. Click here

    INSTALL REAR NO. 1 SEAT RECLINING COVER LH


    1. Attach the 3 claws in the order shown in the illustration to install the cover.

    2. Install the 2 screws.

  16. Click here

    INSTALL RECLINING ADJUSTER RELEASE HANDLE LH


    1. Install the release handle with the screw.

  17. Click here

    INSTALL SEAT ADJUSTER BOLT COVER


    1. Attach the 2 claws to install the cover.

  18. Click here

    INSTALL REAR NO. 1 SEAT ASSEMBLY LH


    1. Install the rear No. 1 seat assembly (Click here).