Click here

REAR NO. 1 SEAT INNER BELT ASSEMBLY (for 60/40 Split Seat Type 60 Side) REMOVAL

Click here
Click here Click here
Tip:

  • Use the same procedure for RHD and LHD vehicles.

  • The procedure listed below is for LHD vehicles.

Click here
  1. Click here

    REMOVE REAR NO. 1 SEAT ASSEMBLY LH


    1. Remove the rear No. 1 seat assembly (Click here).

  2. Click here

    REMOVE SEAT ADJUSTER BOLT COVER


    1. Using a screwdriver, detach the 2 claws and remove the cover.

      Tip:

      Tape the screwdriver tip before use.

  3. Click here

    REMOVE RECLINING ADJUSTER RELEASE HANDLE LH


    1. Remove the screw and release handle.

  4. Click here

    REMOVE REAR NO. 1 SEAT RECLINING COVER LH


    1. Remove the 2 screws.

    2. Detach the 3 claws in the order shown in the illustration, and then remove the cover.

  5. Click here

    REMOVE REAR NO. 1 SEAT RECLINING COVER RH


    1. Remove the 2 screws.

    2. Detach the 4 claws and remove the cover.

  6. Click here

    REMOVE UPPER SEAT TRACK RAIL COVER LH


    1. Using a screwdriver, detach the 2 claws and remove the cover.

      Tip:

      Tape the screwdriver tip before use.

  7. Click here

    REMOVE UPPER SEAT TRACK RAIL COVER RH


    1. Using a screwdriver, detach the 2 claws and remove the cover.

      Tip:

      Tape the screwdriver tip before use.

  8. Click here

    REMOVE REAR NO. 2 SEAT LEG SIDE COVER


    1. A0156BB

      Remove the 4 screws and detach the 4 claws.

    2. A015AUN

      Remove the bolt that is securing the fold seat stopper band and remove the seat leg side cover together with the fold seat stopper band.

  9. Click here

    REMOVE REAR NO. 2 SEAT PROTECTOR


    1. A0155UV

      w/ Rear Seat Side Airbag:

      Detach the claw and remove the wire harness connector.

    2. w/ Seat Heater System:

      Detach the claw and remove the wire harness connector.

    3. A015BO6

      Using a clip remover, remove the clip.

    4. Detach the claw and remove the seat protector from the seat hinge.

    5. Detach the 2 claws, open the protector and remove wire harness.

  10. Click here

    REMOVE REAR NO. 1 SEAT HINGE SUB-ASSEMBLY LH


    1. A0157X7

      w/ Rear Seat Side Airbag:

      Detach the wire harness clamp.

    2. w/ Seat Heater System:

      Detach the wire harness clamp.

    3. Remove the 2 nuts and hinge.

    4. A0155TF

      Detach the cable clamp and disconnect the cable.

  11. Click here

    REMOVE REAR NO. 1 SEAT HINGE SUB-ASSEMBLY RH


    1. Remove the 2 nuts and hinge.

  12. Click here

    REMOVE SEAT BELT ANCHOR COVER CAP


    1. A01568Q

      Detach the claw and open the cap.

    2. A0159WX

      Remove the screw and anchor cover cap.

  13. Click here

    REMOVE REAR SEATBACK STAY COVER LH


    1. Remove the screw.

    2. Detach the 2 claws and remove the cover.

  14. Click here

    REMOVE REAR UNDER SIDE COVER LH


    1. A0155YN

      Detach the 10 claws.

    2. A015CRP

      Remove the 5 screws.

    3. Detach the 2 clips and 2 claws, and remove the cover.

  15. Click here

    REMOVE REAR SEAT CUSHION COVER RH


    1. Remove the 4 screws.

    2. Detach the 2 claws and remove the cover.

  16. Click here

    REMOVE REAR SEAT UNDER TRAY LH COVER


    1. Remove the 2 screws.

    2. Detach the 4 claws and remove the cover.

  17. Click here

    REMOVE REAR NO. 1 SEAT INNER BELT ASSEMBLY LH


    1. Remove the bolt and belt.

      Tip:

      The No. 1 seat 3 point type belt anchor is fixed with the same bolt as the rear No. 1 seat inner belt LH. Therefore, it becomes disconnected when the bolt is removed.

  18. Click here

    DISCONNECT NO. 1 SEAT 3 POINT TYPE BELT ASSEMBLY LH


    1. Disconnect the belt anchor.