FRONT SEAT OUTER BELT ASSEMBLY REMOVAL

Tech Tips


  • Use the same procedure for the RH and LH sides.

  • The procedure listed below is for the LH side.


  1. PRECAUTION

    Note

    After turning the ignition switch off, waiting time may be required before disconnecting the cable from the battery terminal. Therefore, make sure to read the disconnecting the cable from the battery terminal notice before proceeding with work Click here.

  2. DISCONNECT CABLE FROM NEGATIVE BATTERY TERMINAL

    CAUTION:

    Wait at least 90 seconds after disconnecting the cable from the negative (-) battery terminal to disable the SRS system.

    Note

    When disconnecting the cable, some systems need to be initialized after the cable is reconnected Click here.

  3. REMOVE FRONT DOOR SCUFF PLATE

    A0157IK

    1. Detach the 7 claws and 4 clips, and remove the scuff plate.

  4. REMOVE REAR STEP COVER

    A0159DZ

    Tech Tips

    Use the same procedure to remove the step cover on the other side.


    1. Detach the 2 claws and remove the step cover.

  5. REMOVE REAR DOOR SCUFF PLATE

    A015BJQ

    1. Remove the screw.

    2. Detach the 3 claws and 4 clips, and remove the scuff plate.

  6. REMOVE CENTER PILLAR GARNISH COVER

    Tech Tips


    • for Manual Seat:

      When removing the center pillar garnish cover, move the front seat and seatback to the foremost upright position.

    • for Power Seat:

      When removing the center pillar garnish cover, connect the cable to the negative (-) battery terminal and operate the power seat switch to move the front seat and seatback to the foremost upright position.

    • for Power Seat:

      After moving the front seat, disconnect the cable from the negative (-) battery terminal.


    1. A015AD3

      Detach the 2 clips and 2 guides, and remove the cover.

  7. REMOVE CENTER LOWER PILLAR GARNISH

    A0158WN

    Tech Tips


    • for Manual Seat:

      When removing the center pillar garnish cover, move the front seat and seatback to the foremost upright position.

    • for Power Seat:

      When removing the center pillar garnish cover, connect the cable to the negative (-) battery terminal and operate the power seat switch to move the front seat and seatback to the foremost upright position. After moving the front seat, disconnect the cable from the negative (-) battery terminal.


    1. Remove the bolt and seat belt anchor.

    2. A0155QQ

      Detach the 2 claws and 7 clips, and remove the center lower pillar garnish.

  8. REMOVE REAR ASSIST GRIP ASSEMBLY

    A0155B7

    Tech Tips

    Use the same procedure to remove the rear assist grip on the other side.


    1. Detach the 4 claws and remove the 2 assist grip plugs.

    2. A015DJ8

      Remove the 2 bolts.

    3. Detach the 2 claws and remove the rear assist grip.

  9. REMOVE CENTER PILLAR GARNISH

    A0159AD

    1. Remove the bolt.

    2. Detach the 2 clips and 2 guides.

    3. Pass the seat belt anchor through the center pillar garnish, and remove the center pillar garnish.

  10. REMOVE FRONT SEAT OUTER BELT ASSEMBLY

    A015E24

    1. Remove the nut and shoulder anchor.

    2. A0156OOE01

      Disconnect the pretensioner connector labeled A as shown in the illustration.

    3. Disconnect the tension reducer connector labeled B.

    4. w/ Pre-Crash Safety System:

      Disconnect the pre-crash safety connector labeled C.

    5. A015776

      Remove the bolt and seat belt.

  11. REMOVE FRONT SHOULDER BELT ANCHOR ADJUSTER ASSEMBLY

    A015CMD

    1. Remove the 2 bolts and adjuster.