REAR SEAT CUSHION HEATER (for 60/40 Split Seat Type 60 Side) INSTALLATION

CAUTION:

Wear protective gloves. Sharp areas on the parts may injure your hands.

Tech Tips


  • Use the same procedure for RHD and LHD vehicles.

  • The procedure listed below is for LHD vehicles.


  1. INSTALL REAR SEAT CUSHION HEATER ASSEMBLY


    1. Set the seat cushion heater with the name stamp side facing the seat cushion cover.

    2. Install the seat cushion heater with new tack pins.

      A015CH2E01

  2. INSTALL REAR SEPARATE TYPE SEAT CUSHION COVER

    A015CUWE01

    1. Using hog ring pliers, install the seat cushion cover to the seat cushion pad with new hog rings.

      Note


      • Be careful not to damage the cover.

      • When installing the hog rings, avoid wrinkling the cover.

    2. A015CKXE01

      Attach the 3 pieces of fastening tape.

  3. INSTALL SEAT CUSHION COVER WITH PAD


    1. Install the seat cushion cover with pad.

    2. w/ Rear Seat Side Airbag:

      Pass the side airbag wire harness through the hole in the seat cushion.

    3. w/ Seat Heater System:


      1. A015BDM

        Pass the seatback heater wire harness through the hole in the seat cushion.

      2. A015DOT

        Connect the 2 seat heater connectors.

    4. w/ Rear Seat Side Airbag:

      Attach the side airbag wire harness clamps.

  4. CONNECT NO. 1 SEAT 3 POINT TYPE BELT ASSEMBLY LH

    A0156NAE01

    1. Connect the belt anchor.

      Note

      Do not overlap the anchor part of the seat belt and protruding parts of the vehicle body.

  5. INSTALL REAR NO. 1 SEAT INNER BELT ASSEMBLY LH

    A0158WYE01

    1. Install the belt with the bolt.

      Torque:
      42 N*m  { 428 kgf*cm, 31 ft.*lbf }

      Note

      Do not overlap the anchor part of the seat belt and protruding parts of the vehicle body.

      Tech Tips

      The No. 1 seat 3 point type belt anchor is fixed with the same bolt as the rear No. 1 seat inner belt LH. Therefore, connect it when installing the rear No. 1 seat inner belt LH.

  6. INSTALL REAR SEAT UNDER TRAY COVER LH

    A01585Q

    1. Attach the 4 claws to install the cover.

    2. Install the 2 screws.

  7. INSTALL REAR SEAT CUSHION COVER RH

    A015D52

    1. Attach the 2 claws to install the cover.

    2. Install the 4 screws.

  8. INSTALL REAR UNDER SIDE COVER LH

    A015CRP

    1. Attach the 2 claws and 2 clips to install the cover.

    2. Install the 5 screws.

    3. A0155YN

      Attach the 10 claws.

  9. INSTALL REAR SEATBACK STAY COVER LH

    A015E3G

    1. Attach the 2 claws to install the cover.

    2. Install the screw.

  10. INSTALL SEAT BELT ANCHOR COVER CAP


    1. A0159WX

      Install the anchor cover cap with the screw.

    2. A015C6J

      Attach the claw to close the cap.

  11. INSTALL REAR NO. 1 SEAT HINGE SUB-ASSEMBLY RH

    A015AE2

    1. Install the hinge with the 2 nuts.

      Torque:
      42 N*m  { 428 kgf*cm, 31 ft.*lbf }

  12. INSTALL REAR NO. 1 SEAT HINGE SUB-ASSEMBLY LH


    1. A0155TF

      Attach the cable clamp to connect the cable.

    2. A0157X7

      Install the hinge with the 2 nuts.

      Torque:
      42 N*m  { 428 kgf*cm, 31 ft.*lbf }

    3. w/ Rear Seat Side Airbag:

      Attach the wire harness clamp.

    4. w/ Seat Heater System:

      Attach the wire harness clamp.

  13. INSTALL REAR NO. 2 SEAT PROTECTOR


    1. Install the wire harness, and attach 2 claws to close the protector.

    2. A015BO6

      Attach the claw to install the protector to the seat hinge.

    3. Install the clip.

    4. A0155UV

      w/ Rear Seat Side Airbag:

      Attach the claw to install the wire harness connector.

    5. w/ Seat Heater System:

      Attach the claw to install the wire harness connector.

  14. INSTALL REAR NO. 2 SEAT LEG SIDE COVER


    1. A015AUN

      Pass the fold seat stopper band through the seat leg side cover and attach it to the seat cushion frame with the bolt.

    2. A0156BB

      Attach the 4 claws to install the seat leg side cover.

    3. Install the 4 screws.

  15. INSTALL UPPER SEAT TRACK RAIL COVER RH

    A0156Z8

    1. Attach the 2 claws to install the cover.

  16. INSTALL UPPER SEAT TRACK RAIL COVER LH

    A01556W

    1. Attach the 2 claws to install the cover.

  17. INSTALL REAR NO. 1 SEAT RECLINING COVER RH

    A015CKY

    1. Attach the 4 claws to install the cover.

    2. Install the 2 screws.

  18. INSTALL REAR NO. 1 SEAT RECLINING COVER LH

    A015B48E01

    1. Attach the 3 claws in the order shown in the illustration to install the cover.

    2. Install the 2 screws.

  19. INSTALL RECLINING ADJUSTER RELEASE HANDLE LH

    A0155T5

    1. Install the release handle with the screw.

  20. INSTALL SEAT ADJUSTER BOLT COVER

    A01554I

    1. Attach the 2 claws to install the cover.

  21. INSTALL REAR NO. 1 SEAT ASSEMBLY LH


    1. Install the rear No. 1 seat assembly Click here.