REAR SEAT CUSHION HEATER (for 60/40 Split Seat Type 40 Side) INSTALLATION

CAUTION:

Wear protective gloves. Sharp areas on the parts may injure your hands.

Tech Tips


  • Use the same procedure for RHD and LHD vehicles.

  • The procedure listed below is for LHD vehicles.


  1. INSTALL REAR SEAT CUSHION HEATER ASSEMBLY


    1. Set the seat cushion heater with the name stamp side facing the seat cushion cover.

    2. Install the seat cushion heater with new tack pins.

      A015CH2E01

  2. INSTALL REAR SEPARATE TYPE SEAT CUSHION COVER

    A015BXME01

    1. Using hog ring pliers, install the seat cushion cover to the seat cushion pad with new hog rings.

      Note


      • Be careful not to damage the cover.

      • When installing the hog rings, avoid wrinkling the cover.

    2. A015E1OE01

      Attach the 3 pieces of fastening tape.

  3. INSTALL SEAT CUSHION COVER WITH PAD


    1. Install the seat cushion cover with pad.

    2. w/ Rear Seat Side Airbag:

      Pass the side airbag wire harness through the hole in the seat cushion.

    3. w/ Seat Heater System:


      1. A015B2A

        Pass the seatback heater wire harness through the hole in the seat cushion.

      2. A0158YQ

        Connect the 2 seat heater connectors.

    4. w/ Rear Seat Side Airbag:

      Attach the side airbag wire harness clamps.

  4. INSTALL REAR SEAT UNDER TRAY COVER RH

    A01585Q

    1. Attach the 4 claws to install the cover.

    2. Install the 2 screws.

  5. INSTALL REAR UNDER SIDE COVER LH

    A0157GR

    1. Attach the 2 claws and clip to install the cover.

    2. Install the 5 screws.

  6. INSTALL REAR SEAT COVER

    A015BSB

    1. Attach the 2 claws to install the cover.

    2. Install the 3 screws.

    3. A015B8U

      Attach the 12 claws.

  7. INSTALL REAR NO. 1 SEAT HINGE SUB-ASSEMBLY RH


    1. A0155TF

      Attach the cable clamp to connect the cable.

    2. A0157CR

      Install the hinge with the 2 nuts.

      Torque:
      42 N*m  { 428 kgf*cm, 31 ft.*lbf }

    3. w/ Rear Seat Side Airbag:

      Attach the wire harness clamp.

    4. w/ Seat Heater System:

      Attach the wire harness clamp.

  8. INSTALL REAR NO. 1 SEAT HINGE SUB-ASSEMBLY LH

    A0158E3

    1. Install the hinge with the 2 nuts.

      Torque:
      42 N*m  { 428 kgf*cm, 31 ft.*lbf }

  9. INSTALL REAR NO. 2 SEAT PROTECTOR


    1. Install the wire harness, and attach the 2 claws to close the protector.

    2. A0157OL

      Attach the claw to install the protector to the seat hinge.

    3. Install the clip.

    4. A0159RK

      w/ Rear Seat Side Airbag:

      Attach the claw to install the wire harness connector.

    5. w/ Seat Heater System:

      Attach the claw to install the wire harness connector.

  10. INSTALL REAR NO. 2 SEAT LEG SIDE COVER


    1. A015A0P

      Pass the fold seat stopper band through the seat leg side cover and attach it to the seat cushion frame with the bolt.

    2. A015A1T

      Attach the 3 claws to install the seat leg side cover.

    3. Install the 4 screws.

  11. INSTALL UPPER SEAT TRACK RAIL COVER RH

    A015D30

    1. Attach the 2 claws to install the cover.

  12. INSTALL UPPER SEAT TRACK RAIL COVER LH

    A01585I

    1. Attach the 2 claws to install the cover.

  13. INSTALL REAR NO. 1 SEAT RECLINING COVER LH

    A0155OK

    1. Attach the 4 claws to install the cover.

    2. Install the 2 screws.

  14. INSTALL REAR NO. 1 SEAT RECLINING COVER RH

    A015CABE01

    1. Attach the 3 claws in the order shown in the illustration to install the cover.

    2. Install the 2 screws.

  15. INSTALL RECLINING ADJUSTER RELEASE HANDLE RH

    A0157PZ

    1. Install the release handle with the screw.

  16. INSTALL SEAT ADJUSTER BOLT COVER

    A0159SB

    1. Attach the 2 claws to install the cover.

  17. INSTALL REAR NO. 1 SEAT ASSEMBLY RH


    1. Install the rear No. 1 seat assembly Click here.