FRONT SEAT CUSHION HEATER INSTALLATION

CAUTION:

Wear protective gloves. Sharp areas on the parts may injure your hands.

Tech Tips


  • Use the same procedure for RHD and LHD vehicles.

  • The procedure listed below is for LHD vehicles.

  • Use the same procedure for the RH and LH sides.

  • The procedure listed below is for the LH side.


  1. INSTALL FRONT SEAT CUSHION HEATER ASSEMBLY LH


    1. Set the front seat cushion heater assembly LH with the name stamp side facing the front separate type seat cushion cover.

    2. w/o Climate Control Seat System:

      Install the front seat cushion heater assembly LH to the front separate type seat cushion cover with new tack pins.

      A015D9BE02
      Text in Illustration
      *1 Tack Pin *2 Front Separate Type Seat Cushion Cover
      *3 Front Seat Cushion Heater Assembly LH *4 Name Stamp

    3. w/ Climate Control Seat System:

      Install the front seat cushion heater assembly LH to the front separate type seat cushion cover with new tack pins.

      A015B53E01
      Text in Illustration
      *1 Tack Pin *2 Front Separate Type Seat Cushion Cover
      *3 Front Seat Cushion Heater Assembly LH *4 Name Stamp

  2. INSTALL FRONT SEPARATE TYPE SEAT CUSHION COVER

    A015AB6E02
    Text in Illustration
    *1 Hog Ring Pliers

    1. Using hog ring pliers, install the front separate type seat cushion cover to the front separate type seat cushion pad with new hog rings.

      Note


      • Be careful not to damage the cover.

      • When installing the hog rings, avoid wrinkling the cover.

  3. INSTALL SEAT CUSHION COVER WITH PAD


    1. Set the seat cushion cover with pad in place.

    2. A015ADQ

      Attach the hooks to install the seat cushion cover with pad.

    3. Bend the 2 seat frame claws downward.

    4. for Front Passenger Side:


      1. A0157NX

        Attach the 2 clamps to connect the connector holder.

      2. Connect the connector.

    5. w/o Climate Control Seat System:


      1. A015CS8

        Connect the connector and attach the wire harness clamp.

      2. A015DQN

        Connect the connector and attach the 2 wire harness clamps.

    6. w/ Climate Control Seat System:


      1. A015B5P

        Attach the wire harness clamp.

      2. A015CAP

        Connect the 2 connectors and attach the 4 wire harness clamps.

    7. A0156MR

      Install the 2 clips.

  4. INSTALL FRONT POWER SEAT SWITCH LH

    A01573W

    1. Install the front power seat switch LH with the 3 screws.

    2. w/ Seat Position Memory System:

      Connect the 2 connectors.

    3. w/o Seat Position Memory System:

      Connect the connector.

  5. INSTALL FRONT INNER SEAT CUSHION SHIELD LH

    A015D8W

    1. Attach the 2 claws and clip to install the front inner seat cushion shield LH.

    2. Install the screw.

  6. INSTALL FRONT SEAT INNER BELT ASSEMBLY LH

    A015AI8E01

    1. Install the front seat inner belt assembly with the nut.

      Torque:
      42 N*m  { 428 kgf*cm, 31 ft.*lbf }

      Note

      Do not allow the anchor part of the front seat inner belt assembly to overlap the protruding parts of the front seat adjuster.

    2. Connect the connectors and attach the clamps.

  7. INSTALL FRONT SEAT CUSHION SHIELD LH


    1. for Driver Side:

      Connect the connector.

    2. A01597V

      Attach the 2 claws to install the front seat cushion shield LH together with the front inner No. 1 cushion shield LH.

    3. Install the 3 screws.

    4. A015BJU

      Connect the 2 rubber bands.

    5. Install the 2 screws.

  8. INSTALL RECLINING POWER SEAT SWITCH KNOB

    A015CTQ

    1. Attach the 2 claws to install the reclining power seat switch knob.

  9. INSTALL SLIDE AND VERTICAL POWER SEAT SWITCH KNOB

    A0158S6

    1. Attach the 2 claws to install the slide and vertical power seat switch knob.

  10. INSTALL FRONT SEAT ASSEMBLY LH

    Click here