Click here

FRONT SEATBACK HEATER INSTALLATION

Click here
Click here Click here
CAUTION:

Wear protective gloves. Sharp areas on the parts may injure your hands.

Tip:

  • Use the same procedure for RHD and LHD vehicles.

  • The procedure listed below is for LHD vehicles.

  • Use the same procedure for the RH and LH sides.

  • The procedure listed below is for the LH side.

Click here
  1. Click here

    INSTALL FRONT SEATBACK HEATER ASSEMBLY LH


    1. Set the seatback heater with the name stamp side facing the front separate type seatback cover.

    2. A0156MHE02

      w/o Climate Control Seat System:

      Install the front seatback heater assembly LH to the front separate type seatback cover with new tack pins.

      Table 1. Text in Illustration
      *1 Tack Pin *2 Front Separate Type Seatback Cover
      *3 Front Seatback Heater Assembly LH *4 Name Stamp
    3. A015E67E01

      w/ Climate Control Seat System:

      Install the front seatback heater assembly LH to the front separate type seatback cover with new tack pins.

      Table 2. Text in Illustration
      *1 Tack Pin *2 Front Separate Type Seatback Cover
      *3 Front Seatback Heater Assembly LH *4 Name Stamp
  2. Click here

    INSTALL FRONT SEPARATE TYPE SEATBACK COVER


    1. A015631E02

      Attach the fastening tape to install the front separate type seatback cover.

      Table 3. Text in Illustration
      *1 Hog Ring Pliers
      *2 Fastening Tape

    2. Using hog ring pliers, install new hog rings.

      Note:

      • Be careful not to damage the cover.

      • When installing the hog rings, avoid wrinkling the cover.

    3. A015CDTE01

      Pass the seatback cover bracket through the hole of the front separate type seatback pad.

      Table 4. Text in Illustration
      *1 Seatback Cover Bracket
  3. Click here

    INSTALL FRONT SEPARATE TYPE SEATBACK COVER (w/ Climate Control Seat System)


    1. A015DM8E01

      Using hog ring pliers, install the front separate type seatback cover to the front separate type seatback pad with new hog rings.

      Table 5. Text in Illustration
      *1 Hog Ring Pliers
      Note:

      • Be careful not to damage the cover.

      • When installing the hog rings, avoid wrinkling the cover.

    2. A015CDTE01

      Pass the seatback cover bracket through the hole of the front separate type seatback pad.

      Table 6. Text in Illustration
      *1 Seatback Cover Bracket
  4. Click here

    INSTALL SEATBACK COVER WITH PAD


    1. Attach the hooks to install the seatback cover with pad.

      Table 7. Text in Illustration
      *1 Hog Ring
      *2 Hog Ring Pliers
    2. A015APXE01

      Attach the seatback cover bracket with the nut.

      Table 8. Text in Illustration
      *1 Seatback Cover Bracket
      5.0 N*m 51 kgf*cm 44 in.*lbf
      CAUTION:

      After the seatback cover with pad is installed, make sure the seatback cover bracket is not twisted.

    3. Using hog ring pliers, install new hog rings.

      Note:

      Be careful not to damage the cover.

    4. A015DQN

      w/o Climate Control Seat System:

      Connect the connector and attach the 2 wire harness clamps.

    5. A015CAP

      w/ Climate Control Seat System:

      Connect the 2 connectors and attach the 4 wire harness clamps.

  5. Click here

    INSTALL FRONT SEAT HEADREST SUPPORT


    1. Attach the 4 claws to install the 2 front seat headrest supports.

  6. Click here

    INSTALL SEAT CLIMATE CONTROL CONTROLLERLH (w/ Climate Control Seat System)


    1. Attach the 4 hooks to install the seat climate control controller LH.

    2. Attach the 2 claws to connect the seat climate control blower LH.

  7. Click here

    INSTALL FRONT SEATBACK BOARD SUB-ASSEMBLY LH


    1. Move the front seatback board sub-assembly in the direction of the arrow to attach the 2 hooks and install it.

    2. Install the 2 screws.

  8. Click here

    INSTALL FRONT INNER SEAT CUSHION SHIELD LH


    1. Attach the 2 claws and clip to install the front inner seat cushion shield LH.

    2. Install the screw.

  9. Click here

    INSTALL FRONT SEAT INNER BELT ASSEMBLY LH


    1. Install the front seat inner belt assembly with the nut.

      42 N*m 428 kgf*cm 31 ft.*lbf
      Note:

      Do not allow the anchor part of the front seat inner belt assembly to overlap the protruding parts of the front seat adjuster.

    2. Connect the connectors and attach the clamps.

  10. Click here

    INSTALL FRONT SEAT CUSHION SHIELD LH


    1. for Driver Side:

      Connect the connector.

    2. A01597V

      Attach the 2 claws to install the front seat cushion shield LH together with the front inner No. 1 cushion shield LH.

    3. Install the 3 screws.

    4. A015BJU

      Connect the 2 rubber bands.

    5. Install the 2 screws.

  11. Click here

    INSTALL RECLINING POWER SEAT SWITCH KNOB


    1. Attach the 2 claws to install the reclining power seat switch knob.

  12. Click here

    INSTALL SLIDE AND VERTICAL POWER SEAT SWITCH KNOB


    1. Attach the 2 claws to install the slide and vertical power seat switch knob.

  13. Click here

    INSTALL FRONT SEAT ASSEMBLY LH

    (Click here)