LUMBAR SUPPORT ADJUSTER ASSEMBLY (for Power Seat) INSTALLATION

CAUTION:

Wear protective gloves. Sharp areas on the parts may injure your hands.

Tech Tips


  • Use the same procedure for RHD and LHD vehicles.

  • The procedure listed below is for LHD vehicles.


  1. INSTALL LUMBAR SUPPORT ADJUSTER ASSEMBLY LH


    1. A015561

      Install the lumbar support adjuster assembly LH with the 2 screws.

    2. Connect the connector.

    3. A015DVRE01
      Text in Illustration
      *1 Cable Clamp
      *2 Hook

      Attach the 4 hooks to install the seatback spring.

    4. Install the 4 springs.

    5. Connect the active headrest cable to the seatback spring with the cable clamp.

  2. INSTALL FRONT SEATBACK PROTECTOR

    A015CB8E01
    Text in Illustration
    *1 Double-sided tape

    1. Apply double-sided tape as shown in the illustration.

    2. Install the front seatback protector.

  3. INSTALL SEATBACK COVER WITH PAD

    A0155XCE01

    1. Attach the hooks to install the seatback cover with pad.

      Text in Illustration
      *1 Hog Ring
      *2 Hog Ring Pliers
    2. A015APXE01
      Text in Illustration
      *1 Seatback Cover Bracket

      Attach the seatback cover bracket with the nut.

      Torque:
      5.0 N*m  { 51 kgf*cm, 44 in.*lbf }

      CAUTION:

      After the seatback cover with pad is installed, make sure the seatback cover bracket is not twisted.

    3. Using hog ring pliers, install new hog rings.

      Note

      Be careful not to damage the cover.

    4. A015DQN

      w/o Climate Control Seat System:

      Connect the connector and attach the 2 wire harness clamps.

    5. A015CAP

      w/ Climate Control Seat System:

      Connect the 2 connectors and attach the 4 wire harness clamps.

  4. INSTALL FRONT SEAT HEADREST SUPPORT

    A01568X

    1. Attach the 4 claws to install the 2 front seat headrest supports.

  5. INSTALL SEAT CLIMATE CONTROL CONTROLLER LH (w/ Climate Control Seat System)

    A015A71

    1. Install the seat climate control controller LH with the 2 screws.

    2. Attach the wire harness clamp.

    3. A0157OU

      Attach the 4 claws to connect the seat climate control blower LH.

  6. INSTALL FRONT SEATBACK BOARD SUB-ASSEMBLY LH

    A01590O

    1. Move the front seatback board sub-assembly in the direction of the arrow to attach the 2 hooks and install it.

    2. Install the 2 screws.

  7. INSTALL FRONT INNER SEAT CUSHION SHIELD LH

    A015D8W

    1. Attach the 2 claws and clip to install the front inner seat cushion shield LH.

    2. Install the screw.

  8. INSTALL FRONT SEAT INNER BELT ASSEMBLY LH

    A015AI8E01

    1. Install the front seat inner belt assembly with the nut.

      Torque:
      42 N*m  { 428 kgf*cm, 31 ft.*lbf }

      Note

      Do not allow the anchor part of the front seat inner belt assembly to overlap the protruding parts of the front seat adjuster.

    2. Connect the connectors and attach the clamps.

  9. INSTALL FRONT SEAT CUSHION SHIELD LH


    1. for Driver Side:

      Connect the connector.

    2. A01597V

      Attach the 2 claws to install the front seat cushion shield LH together with the front inner No. 1 cushion shield LH.

    3. Install the 3 screws.

    4. A015BJU

      Connect the 2 rubber bands.

    5. Install the 2 screws.

  10. INSTALL RECLINING POWER SEAT SWITCH KNOB

    A015CTQ

    1. Attach the 2 claws to install the reclining power seat switch knob.

  11. INSTALL SLIDE AND VERTICAL POWER SEAT SWITCH KNOB

    A0158S6

    1. Attach the 2 claws to install the slide and vertical power seat switch knob.

  12. INSTALL FRONT SEAT ASSEMBLY LH

    Click here