LUMBAR SUPPORT ADJUSTER ASSEMBLY (for Manual Seat) REMOVAL

CAUTION:

Wear protective gloves. Sharp areas on the parts may injure your hands.

Tech Tips


  • Use the same procedure for RHD and LHD vehicles.

  • The procedure listed below is for LHD vehicles.


  1. REMOVE FRONT SEAT ASSEMBLY LH


    1. Remove the front seat assembly Click here.

  2. REMOVE VERTICAL ADJUSTER COVER LH (for 8 Way Seat Type)

    A015C1M

    1. Using a screwdriver, detach the 2 claws and remove the vertical adjuster cover LH.

      Tech Tips

      Tape the screwdriver tip before use.

  3. REMOVE VERTICAL ADJUSTING HANDLE LH (for 8 Way Seat Type)

    A015DU7

    1. Remove the 2 screws and vertical adjusting handle LH.

  4. REMOVE VERTICAL SEAT ADJUSTER KNOB (for 8 Way Seat Type)

    A0159FT

    1. Remove the snap ring and vertical seat adjuster knob.

  5. REMOVE RECLINING ADJUSTER RELEASE HANDLE LH

    A0158UEE01

    1. Lift the reclining adjuster release handle LH.

    2. Using a screwdriver, detach the claw and remove the reclining adjuster release handle LH.

      Tech Tips

      Tape the screwdriver tip before use.

  6. REMOVE FRONT SEAT CUSHION SHIELD LH


    1. A015ANG

      w/ Seatback Board:

      Disconnect the 2 rubber bands from the 2 hooks.

    2. A015CXB

      w/o Seatback Board:

      Disconnect the rubber band from the 2 hooks.

    3. A0157H3E02

      for 4 Way Seat Type:


      1. Remove the 2 screws.

      2. Detach the 3 claws in the order shown in the illustration, and then remove the front seat cushion shield LH.

    4. A0159PPE01

      for 8 Way Seat Type:


      1. Remove the 3 screws.

      2. Detach the 3 claws in the order shown in the illustration, and then remove the front seat cushion shield LH.

    5. w/ Lumbar Support:

      Disconnect the lumbar switch connector.

  7. REMOVE FRONT SEAT INNER BELT ASSEMBLY LH


    1. Disconnect the connectors and detach the clamps.

    2. A015D6H

      Remove the nut and front seat inner belt assembly.

  8. REMOVE FRONT INNER SEAT CUSHION SHIELD LH

    A0159VQ

    1. Remove the screw.

    2. Detach the claw and clip, and then remove the front inner seat cushion shield LH.

  9. REMOVE FRONT SEATBACK BOARD SUB-ASSEMBLY LH (w/ Seatback Board)

    A015BS5

    1. Remove the 2 screws.

    2. Move the front seatback board sub-assembly LH in the direction of the arrow to detach the 2 hooks and remove it.

  10. REMOVE FRONT SEAT HEADREST SUPPORT (w/ Active Headrest)

    A0156HC

    1. Detach the 4 claws and remove the 2 front seat headrest supports.

  11. REMOVE SEATBACK COVER WITH PAD


    1. w/ Seatback Board:


      1. A015DYHE01

        Remove the 3 hog rings and detach the 9 hooks.

      2. A015APX

        w/ Front Seat Side Airbag:

        Remove the nut and seatback cover bracket from the seat frame.

    2. w/o Seatback Board:


      1. A0157S5

        Remove the 3 hog rings.

      2. A01568J

        Open the 2 fasteners, and then open the front separate type seatback cover.

      3. A015APX

        w/ Front Seat Side Airbag:

        Remove the nut and seatback cover bracket from the seat frame.

      4. A015E4A

        Detach the 4 claws and remove the 2 front seat headrest supports.

    3. Remove the seatback cover with pad from the seatback frame.

  12. REMOVE LUMBAR SUPPORT ADJUSTER ASSEMBLY LH (w/ Lumbar Support)


    1. A015B73E01

      Remove the 4 springs.

    2. Remove the cable clamp and disconnect the active headrest cable from the seatback spring.

    3. Detach the 4 hooks and remove the seatback spring.

    4. A0155TG

      Disconnect the lumbar support adjuster connector.

    5. Remove the 2 screws and lumbar support adjuster.