REAR NO. 1 SEAT ASSEMBLY (for 60/40 Split Seat Type 60 Side) DISASSEMBLY

CAUTION:

Wear protective gloves. Sharp areas on the parts may injure your hands.

Tech Tips


  • Use the same procedure for RHD and LHD vehicles.

  • The procedure listed below is for LHD vehicles.


  1. REMOVE SEAT ADJUSTER BOLT COVER

    A01554I

    1. Using a screwdriver, detach the 2 claws and remove the cover.

      Tech Tips

      Tape the screwdriver tip before use.

  2. REMOVE RECLINING ADJUSTER RELEASE HANDLE LH

    A0155T5

    1. Remove the screw and release handle.

  3. REMOVE REAR NO. 1 SEAT RECLINING COVER LH

    A0155WKE01

    1. Remove the 2 screws.

    2. Detach the 3 claws in the order shown in the illustration, and then remove the cover.

  4. REMOVE REAR NO. 1 SEAT RECLINING COVER RH

    A015CKY

    1. Remove the 2 screws.

    2. Detach the 4 claws and remove the cover.

  5. REMOVE UPPER SEAT TRACK RAIL COVER LH

    A0159XW

    1. Using a screwdriver, detach the 2 claws and remove the cover.

      Tech Tips

      Tape the screwdriver tip before use.

  6. REMOVE UPPER SEAT TRACK RAIL COVER RH

    A015BF3

    1. Using a screwdriver, detach the 2 claws and remove the cover.

      Tech Tips

      Tape the screwdriver tip before use.

  7. REMOVE NO. 1 SEAT CUSHION COVER

    A0156QI

    1. Detach the 4 claws and remove the 2 covers.

  8. REMOVE REAR NO. 2 SEAT LEG SIDE COVER


    1. A0156BB

      Remove the 4 screws and detach the 4 claws.

    2. A015AUN

      Remove the bolt that is securing the fold seat stopper band and remove the seat leg side cover together with the fold seat stopper band.

  9. REMOVE FOLD SEAT STOPPER BAND ASSEMBLY


    1. Remove the fold seat stopper band from the seat leg side cover.

  10. REMOVE REAR SEAT SIDE HINGE FEMALE COVER

    A015CYP

    1. Using a screwdriver, detach the 6 claws and remove the 2 covers.

      Tech Tips

      Tape the screwdriver tip before use.

  11. REMOVE REAR SEAT SIDE HINGE MALE COVER LH

    A0157HN

    1. Detach the clip and remove the cover.

  12. REMOVE REAR SEAT SIDE HINGE MALE COVER RH


    1. Detach the clip and remove the cover.

  13. REMOVE REAR NO. 2 SEAT PROTECTOR


    1. A0155UV

      w/ Rear Seat Side Airbag:

      Detach the claw and remove the wire harness connector.

    2. w/ Seat Heater System:

      Detach the claw and remove the wire harness connector.

    3. A015BO6

      Using a clip remover, remove the clip.

    4. Detach the claw and remove the seat protector from the seat hinge.

    5. Detach the 2 claws, open the protector and remove wire harness.

  14. REMOVE REAR NO. 1 SEAT HINGE SUB-ASSEMBLY LH


    1. A0157X7

      w/ Rear Seat Side Airbag:

      Detach the wire harness clamp.

    2. w/ Seat Heater System:

      Detach the wire harness clamp.

    3. Remove the 2 nuts and hinge.

    4. A0155TF

      Detach the cable clamp and disconnect the cable.

  15. REMOVE REAR NO. 1 SEAT HINGE SUB-ASSEMBLY RH

    A015AE2

    1. Remove the 2 nuts and hinge.

  16. REMOVE SEAT BELT ANCHOR COVER CAP


    1. A01568Q

      Detach the claw and open the cap.

    2. A0159WX

      Remove the screw and anchor cover cap.

  17. REMOVE REAR SEATBACK STAY COVER LH

    A015E3G

    1. Remove the screw.

    2. Detach the 2 claws and remove the cover.

  18. REMOVE REAR UNDER SIDE COVER LH


    1. A0155YN

      Detach the 10 claws.

    2. A015CRP

      Remove the 5 screws.

    3. Detach the 2 clips and 2 claws, and remove the cover.

  19. REMOVE NO. 1 SEAT CUSHION PLATE


    1. A015B2F

      Detach the 3 claws and remove the seat cushion plate.

  20. REMOVE REAR SEAT CUSHION COVER RH

    A015D52

    1. Remove the 4 screws.

    2. Detach the 2 claws and remove the cover.

  21. REMOVE REAR SEAT UNDER TRAY COVER LH

    A01585Q

    1. Remove the 2 screws.

    2. Detach the 4 claws and remove the cover.

  22. REMOVE REAR SEAT TRACK HANDLE SUB-ASSEMBLY


    1. A0157IS

      Remove the 2 screws and seat track handle.

    2. A0159IZ

      Detach the 2 cable clamps and disconnect the 2 cables.

    3. A0157BR

      Detach the cable clamp and disconnect the cable.

  23. REMOVE FOLD SEAT LOCK CONTROL CABLE SUB-ASSEMBLY

  24. REMOVE REAR NO. 1 SEAT INNER BELT ASSEMBLY LH

    A0156VCE01

    1. Remove the bolt and belt.

      Tech Tips

      The No. 1 seat 3 point type belt anchor is fixed with the same bolt as the rear No. 1 seat inner belt LH. Therefore, it becomes disconnected when the bolt is removed.

  25. DISCONNECT NO. 1 SEAT 3 POINT TYPE BELT ASSEMBLY LH

    A0156NAE02

    1. Disconnect the belt anchor.

  26. REMOVE SEAT CUSHION COVER WITH PAD


    1. w/ Rear Seat Side Airbag:


      1. Detach the side airbag wire harness clamps.

      2. Remove the side airbag wire harness through the hole in the seat cushion.

    2. w/ Seat Heater System:


      1. A015DOT

        Disconnect the 2 seat heater connectors.

      2. A0159XP

        Remove the seatback heater wire harness through the hole in the seat cushion.

    3. Remove the seat cushion cover with pad.

  27. REMOVE REAR SEPARATE TYPE SEAT CUSHION COVER


    1. A015CKXE01

      Detach the 3 pieces of fastening tape.

    2. A015DMV

      Remove the hog rings and cover.

  28. REMOVE REAR SEAT CUSHION HEATER ASSEMBLY (w/ Seat Heater System)

    A0157GG

    1. Cut off the tack pins which fasten the seat heater to the seat cushion cover, and then remove the seat cushion heater from the seat cushion cover.

  29. REMOVE REAR SEATBACK COVER

    A015D4NE01

    1. Using a screwdriver, detach the 4 claws and remove the cover.

      Tech Tips

      Tape the screwdriver tip before use.

  30. REMOVE REAR SEATBACK BOARD SUB-ASSEMBLY LH

    A0159SS

    1. w/ Center Armrest:


      1. Detach the 2 claws on the top of the board.

      2. Pull up the board to detach the 2 claws on the bottom of the board and remove it.

    2. A015E1N

      w/o Center Armrest:


      1. Detach the 3 claws on the top of the board.

      2. Pull up the board to detach the 3 claws on the bottom of the board and remove it.

  31. REMOVE REAR SEAT HEADREST ASSEMBLY

  32. REMOVE REAR NO. 1 SEAT HEADREST SUPPORT ASSEMBLY

    A015C63

    1. w/ Center Armrest:

      Detach the 4 claws and remove the 2 supports.

    2. A01567O

      w/o Center Armrest:

      Detach the 8 claws and remove the 4 supports.

  33. REMOVE SHOULDER BELT ANCHOR COVER

    A0158FBE01

    1. Using a screwdriver, detach the 2 claws and remove the cover.

      Tech Tips

      Tape the screwdriver tip before use.

  34. REMOVE REAR SEAT BELT HOLE COVER LH

    A0159WD

    1. Remove the screw.

    2. Detach the 4 claws and remove the cover.

  35. REMOVE SEATBACK COVER WITH PAD


    1. A015581

      w/ Center Armrest:

      Remove the hog rings.

    2. A0157JE

      w/o Center Armrest:

      Remove the hog rings.

    3. w/ Rear Seat Side Airbag:


      1. A0159P8

        Remove the cap nut and seatback cover bracket from the seat frame.

      2. Remove the side airbag wire harness through the hole in the seatback.

    4. w/ Seat Heater System:


      1. A015AWWE01

        Cut the cable tie and disconnect the seatback heater wire harness.

      2. A015AZA

        Remove the seatback heater wire harness through the hole in the seatback.

    5. A0156D5

      w/ Center Armrest:

      Pull the seat belt into the inside of the seat.

    6. A015C55

      w/o Center Armrest:

      Pull the seat belt into the inside of the seat.

    7. Remove the seatback cover with pad.

  36. REMOVE REAR SEPARATE TYPE SEATBACK COVER


    1. A0155JE

      w/ Rear Seat Side Airbag:

      Disconnect the seatback cover bracket from the seatback pad.

    2. A015E7K

      w/ Center Armrest:

      Remove the hog rings and rear seatback cover.

    3. A015CLM

      w/o Center Armrest:

      Remove the hog rings and rear seatback cover.

  37. REMOVE REAR SEATBACK HEATER ASSEMBLY (w/ Seat Heater System)

    A015E4H

    1. Cut off the tack pins which fasten the seatback heater to the seatback cover, and then remove the seatback heater from the seatback cover.

  38. REMOVE SEATBACK STOPPER PLATE


    1. A015DSR

      w/ Center Armrest:


      1. Using a T40 "TORX" socket, remove the 2 bolts.

      2. Remove the bolt and stopper plate.

      3. Remove the bush from the stopper plate.

    2. A01590P

      w/o Center Armrest:


      1. Using a T40 "TORX" socket, remove the 2 bolts.

      2. Remove the bolt and stopper plate.

      3. Remove the bush from the stopper plate.

  39. REMOVE REAR CENTER SEAT ARMREST ASSEMBLY (w/ Center Armrest)

    A015DOV

    1. Using a T40 "TORX" socket, remove the 2 bolts and center seat armrest.

  40. REMOVE REAR CENTER SEAT HEADREST ASSEMBLY (w/ Center Armrest)

  41. REMOVE NO. 1 SEAT ARMREST PLATE (w/ Center Armrest)

    A015AOT

    1. Using a moulding remover, detach the 4 clips and 2 claws, and then remove the 2 armrest plates.

  42. REMOVE CUP HOLDER ASSEMBLY (w/ Center Armrest)


    1. A0159K6

      Remove the 2 screws.

    2. A015708

      Using a moulding remover, detach the 2 clips and remove the cup holder.

  43. REMOVE REAR SEAT RECLINING COVER LH

    A015AOA

    1. Remove the screw.

    2. Detach the claw and remove the cover.

  44. REMOVE REAR NO. 2 SEAT RECLINING COVER LH

    A015DO8

    1. Remove the screw.

    2. Detach the clamp and remove the cover.

  45. REMOVE REAR NO. 1 SEAT RECLINING COVER RH

    A0156C8

    1. Remove the screw.

    2. Detach the claw and remove the cover.

  46. REMOVE REAR SEATBACK HINGE COVER LH

    A0155AM

    1. Remove the screw.

    2. Detach the claw and remove the cover.

  47. REMOVE REAR LOWER SEATBACK COVER SUB-ASSEMBLY LH

    A015BF9

    1. Remove the 4 screws.

    2. Detach the 4 claws and remove the cover.

  48. REMOVE REAR SEAT SHOULDER BELT HOLE COVER LH

    A015AWY

    1. Using a screwdriver, detach the 3 claws and remove the shoulder belt hole cover.

  49. REMOVE NO. 1 SEAT 3 POINT TYPE BELT ASSEMBLY LH

    A0156JI

    1. Remove the 3 nuts and belt sensor.

    2. Remove the nut and then remove the outer belt.

  50. REMOVE RECLINING ADJUSTING CABLE ASSEMBLY LH

    A0157IE

    1. Detach the 2 cable clamps and disconnect the cable.

    2. Detach the clamp and remove the adjusting cable.

  51. REMOVE NO. 2 FOLD SEAT LOCK CONTROL CABLE ASSEMBLY

    A015BZU

    1. Detach the 2 cable clamps and disconnect the cable.

    2. Detach the clamp and remove the lock control cable.

  52. REMOVE REAR SEATBACK FRAME SUB-ASSEMBLY LH

    A015D8O

    1. LH Side:

      Using a T40 "TORX" socket, remove the 2 bolts.

    2. RH Side:

      Using a T55 "TORX" socket, remove the 2 bolts.

    3. Remove the seatback frame sub-assembly.

    4. A0158ZL

      Remove the lower seatback cover.

  53. REMOVE FOLD SEAT LOCK CONTROL CABLE SUB-ASSEMBLY

    A015980

    1. Detach the 2 cable clamps and disconnect the 2 cables.

    2. Remove the 2 fold seat lock cables.

  54. REMOVE REAR NO. 1 SEAT LOCK CABLE ASSEMBLY


    1. A01577Q

      Remove the 2 nuts and lower seat track bracket.

    2. A015D79E01

      Cut the cable tie and disconnect the cable.

    3. Detach the 3 cable clamps and disconnect the 3 cables.

    4. Detach the clamp and remove the seat lock cable.

  55. REMOVE REAR SEAT CUSHION HOLDER BRACKET LH (w/ Seat Heater System)

    A015CMH

    1. Disconnect the seat wire connector.

    2. Remove the 2 screws and holder bracket.

  56. REMOVE SEAT HEATER CONTROL SUB-ASSEMBLY LH (w/ Seat Heater System)

    A0157XZ

    1. Detach the 2 claws and remove the seat heater control.

  57. REMOVE REAR SEAT INNER BELT ASSEMBLY

    A0155T4E01

    1. Remove the bolt and belt.

  58. REMOVE NO. 1 SEAT LEG ASSEMBLY LH

    A01579H

    1. Using a T40 "TORX" socket, remove the 2 bolts and seat leg assembly.

  59. REMOVE REAR SEAT CUSHION FRAME SUB-ASSEMBLY LH

    A015B3F

    1. Using a T40 "TORX" socket, remove the bolt.

    2. Remove the 5 nuts and seat cushion frame.

  60. REMOVE REAR SEAT LOCK CONTROL LEVER LH

    A015AP4

    1. Remove the bolt and lock control lever.