REAR NO. 1 SEAT ASSEMBLY (for 60/40 Split Seat Type 40 Side) REASSEMBLY

CAUTION:

Wear protective gloves. Sharp areas on the parts may injure your hands.

Tech Tips


  • Use the same procedure for RHD and LHD vehicles.

  • The procedure listed below is for LHD vehicles.


  1. INSTALL REAR NO. 1 SEAT LOCK CONTROL LEVER

    A015BAO

    1. Install the lock control lever with the bolt.

      Torque:
      13 N*m  { 133 kgf*cm, 10 ft.*lbf }

  2. INSTALL REAR SEAT CUSHION FRAME SUB-ASSEMBLY RH

    A015AC9

    1. Temporarily install the seat cushion frame with the 5 nuts and bolt.

    2. Tighten the 5 nuts.

      Torque:
      42 N*m  { 428 kgf*cm, 31 ft.*lbf }

    3. Using a T40 "TORX" socket, tighten the bolt.

      Torque:
      21 N*m  { 214 kgf*cm, 15 ft.*lbf }

  3. INSTALL REAR NO. 1 SEAT INNER BELT ASSEMBLY RH

    A015D7KE01

    1. Install the belt with the bolt.

      Torque:
      42 N*m  { 428 kgf*cm, 31 ft.*lbf }

      Note

      Do not overlap the anchor part of the seat belt and protruding parts of the seat.

  4. INSTALL SEAT HEATER CONTROL SUB-ASSEMBLY RH (w/ Seat Heater System)

    A0157XZ

    1. Attach the 2 claws to install the seat heater control.

  5. INSTALL REAR SEAT CUSHION HOLDER BRACKET RH (w/ Seat Heater System)

    A0158EN

    1. Install the holder bracket with the 2 screws.

    2. Connect the seat wire connector.

  6. INSTALL REAR NO. 1 SEAT LOCK CABLE ASSEMBLY

    A0157VK

    1. Attach the clamp to install the seat lock cable.

    2. Attach the 3 cable clamps to connect the 3 cables.

    3. A0159L8

      Install the lower seat track bracket with the 2 nuts.

      Torque:
      21 N*m  { 214 kgf*cm, 15 ft.*lbf }
    4. A01577Q

      Install the lower seat track bracket with the 2 nuts.

      Torque:
      21 N*m  { 214 kgf*cm, 15 ft.*lbf }

  7. INSTALL FOLD SEAT LOCK CONTROL CABLE SUB-ASSEMBLY

    A0158VC

    1. Install the 2 fold seat lock control cables.

    2. Attach the 2 cable clamps to connect the 2 cables.

  8. INSTALL REAR SEATBACK FRAME SUB-ASSEMBLY RH

    A0159FP

    1. Temporarily install the seatback frame with the 4 bolts.

    2. Using a T40 "TORX" socket, tighten the 4 bolts.

      Torque:
      42 N*m  { 428 kgf*cm, 31 ft.*lbf }

  9. INSTALL NO. 1 FOLD SEAT LOCK CONTROL CABLE ASSEMBLY

    A015E71

    1. Attach the clamp to install the lock control cable.

    2. Attach the 2 cable clamps to connect the cable.

  10. INSTALL RECLINING ADJUSTING CABLE ASSEMBLY RH

    A015CJN

    1. Attach the clamp to install the adjusting cable.

    2. Attach the 2 cable clamps to connect the cable.

  11. INSTALL REAR NO. 1 SEAT RECLINING COVER RH

    A015CWN

    1. Attach the claw to install the cover.

    2. Install the screw.

  12. INSTALL REAR NO. 2 SEAT RECLINING COVER LH

    A015DO8

    1. Attach the clamp to install the cover.

    2. Install the screw.

  13. INSTALL REAR SEAT RECLINING COVER RH

    A015AOA

    1. Attach the claw to install the cover.

    2. Install the screw.

  14. INSTALL REAR SEAT RECLINING COVER LH


    1. Attach the claw to install the cover.

    2. Install the screw.

  15. INSTALL REAR SEATBACK HEATER ASSEMBLY (w/ Seat Heater System)


    1. Set the seatback heater with the name stamp side facing the seatback cover.

    2. Install the seatback heater with new tack pins.

      A015DFIE01

  16. INSTALL REAR SEPARATE TYPE SEATBACK COVER

    A015CO2E01

    1. Using hog ring pliers, install the seatback cover with new hog rings.

      Note


      • Be careful not to damage the cover.

      • When installing the hog rings, avoid wrinkling the cover.

    2. A0158S5

      w/ Rear Seat Side Airbag:

      Connect the seatback cover bracket to the seatback pad.

  17. INSTALL SEATBACK COVER WITH PAD


    1. Install the seatback cover with pad.

    2. w/ Rear Seat Side Airbag:

      Pass the side airbag wire harness through the hole in the seatback.

    3. w/ Seat Heater System:


      1. A0157U1

        Pass the seatback heater wire harness through the hole in the seatback.

      2. A0157H9E01

        Connect the seatback heater wire harness and install a new cable tie.

    4. A015DLA

      w/ Rear Seat Side Airbag:

      Install the seatback cover bracket to the seat frame with the cap nut.

      Torque:
      5.5 N*m  { 56 kgf*cm, 49 in.*lbf }

      CAUTION:

      After the seatback trim cover is assembled, make sure the side airbag strap is not twisted.

    5. A015CI5E01

      Using hog ring pliers, install new hog rings to the seatback frame.

  18. INSTALL REAR NO. 1 SEAT HEADREST SUPPORT ASSEMBLY

    A015C63

    1. Attach the 4 claws to install the 2 supports.

  19. INSTALL REAR SEAT HEADREST ASSEMBLY

  20. INSTALL REAR SEATBACK BOARD SUB-ASSEMBLY RH

    A0159K1

    1. Push the board down to attach the 2 claws on the bottom.

    2. Attach the 2 claws on the top of the board to install it.

  21. INSTALL REAR SEATBACK COVER

    A0158JU

    1. Attach the 4 claws to install the cover.

  22. INSTALL REAR SEAT CUSHION HEATER ASSEMBLY (w/ Seat Heater System)


    1. Set the seat cushion heater with the name stamp side facing the seat cushion cover.

    2. Install the seat cushion heater with new tack pins.

      A015CH2E01

  23. INSTALL REAR SEPARATE TYPE SEAT CUSHION COVER

    A015BXME01

    1. Using hog ring pliers, install the seat cushion cover to the seat cushion pad with new hog rings.

      Note


      • Be careful not to damage the cover.

      • When installing the hog rings, avoid wrinkling the cover.

    2. A015E1OE01

      Attach the 3 pieces of fastening tape.

  24. INSTALL SEAT CUSHION COVER WITH PAD


    1. Install the seat cushion cover with pad.

    2. w/ Rear Seat Side Airbag:

      Pass the side airbag wire harness through the hole in the seat cushion.

    3. w/ Seat Heater System:


      1. A015B2A

        Pass the seatback heater wire harness through the hole in the seat cushion.

      2. A0158YQ

        Connect the 2 seat heater connectors.

    4. w/ Rear Seat Side Airbag:

      Attach the side airbag wire harness clamps.

  25. INSTALL FOLD SEAT LOCK CONTROL CABLE SUB-ASSEMBLY

  26. INSTALL REAR SEAT TRACK HANDLE SUB-ASSEMBLY


    1. A0157BR

      Attach the cable clamp to connect the cable.

    2. A0159IZ

      Attach the 2 cable clamps to connect the 2 cables.

    3. A0157IS

      Install the seat track handle with the 2 screws.

  27. INSTALL REAR SEAT UNDER TRAY COVER RH

    A01585Q

    1. Attach the 4 claws to install the cover.

    2. Install the 2 screws.

  28. INSTALL NO. 1 SEAT CUSHION PLATE

    A015B2F

    1. Attach the 3 claws to install the seat cushion plate.

  29. INSTALL REAR UNDER SIDE COVER LH

    A0157GR

    1. Attach the 2 claws and clip to install the cover.

    2. Install the 5 screws.

  30. INSTALL REAR SEAT COVER

    A015BSB

    1. Attach the 2 claws to install the cover.

    2. Install the 3 screws.

    3. A015B8U

      Attach the 12 claws.

  31. INSTALL REAR NO. 1 SEAT HINGE SUB-ASSEMBLY RH


    1. A0155TF

      Attach the cable clamp to connect the cable.

    2. A0157CR

      Install the hinge with the 2 nuts.

      Torque:
      42 N*m  { 428 kgf*cm, 31 ft.*lbf }

    3. w/ Rear Seat Side Airbag:

      Attach the wire harness clamp.

    4. w/ Seat Heater System:

      Attach the wire harness clamp.

  32. INSTALL REAR NO. 1 SEAT HINGE SUB-ASSEMBLY LH

    A0158E3

    1. Install the hinge with the 2 nuts.

      Torque:
      42 N*m  { 428 kgf*cm, 31 ft.*lbf }

  33. INSTALL REAR NO. 2 SEAT PROTECTOR


    1. Install the wire harness, and attach the 2 claws to close the protector.

    2. A0157OL

      Attach the claw to install the protector to the seat hinge.

    3. Install the clip.

    4. A0159RK

      w/ Rear Seat Side Airbag:

      Attach the claw to install the wire harness connector.

    5. w/ Seat Heater System:

      Attach the claw to install the wire harness connector.

  34. INSTALL REAR SEAT SIDE HINGE MALE COVER RH

    A0157HN

    1. Attach the clip to install the cover.

  35. INSTALL REAR SEAT SIDE HINGE MALE COVER LH


    1. Attach the clip to install the cover.

  36. INSTALL REAR SEAT SIDE HINGE FEMALE COVER

    A015CYP

    1. Attach the 6 claws to install the 2 covers.

  37. INSTALL FOLD SEAT STOPPER BAND ASSEMBLY


    1. Install the fold seat stopper band to the seat leg side cover.

  38. INSTALL REAR NO. 2 SEAT LEG SIDE COVER


    1. A015A0P

      Pass the fold seat stopper band through the seat leg side cover and attach it to the seat cushion frame with the bolt.

    2. A015A1T

      Attach the 3 claws to install the seat leg side cover.

    3. Install the 4 screws.

  39. INSTALL NO. 1 SEAT CUSHION COVER

    A0158SE

    1. Attach the 4 claws to install the 2 covers.

  40. INSTALL UPPER SEAT TRACK RAIL COVER RH

    A015D30

    1. Attach the 2 claws to install the cover.

  41. INSTALL UPPER SEAT TRACK RAIL COVER LH

    A01585I

    1. Attach the 2 claws to install the cover.

  42. INSTALL REAR NO. 1 SEAT RECLINING COVER LH

    A0155OK

    1. Attach the 4 claws to install the cover.

    2. Install the 2 screws.

  43. INSTALL REAR NO. 1 SEAT RECLINING COVER RH

    A015CABE01

    1. Attach the 3 claws in the order shown in the illustration to install the cover.

    2. Install the 2 screws.

  44. INSTALL RECLINING ADJUSTER RELEASE HANDLE RH

    A0157PZ

    1. Install the release handle with the screw.

  45. INSTALL SEAT ADJUSTER BOLT COVER

    A0159SB

    1. Attach the 2 claws to install the cover.