REAR NO. 2 SEAT ASSEMBLY (except Face to Face Seat Type) DISASSEMBLY

CAUTION:

Wear protective gloves. Sharp areas on the parts may injure your hands.

Tech Tips

Use the same procedure for the RH and LH sides.
The procedure listed below is for the LH side.

REMOVE SEAT ADJUSTER BOLT COVER
Text in Illustration

*1 Protective Tape
1. Using a screwdriver, detach the 2 claws and remove the cover.
  
  Tech Tips
  
  Tape the screwdriver tip before use.
REMOVE NO. 2 RECLINING ADJUSTER RELEASE HANDLE LH
1. Remove the screw and release handle.
REMOVE RECLINING ADJUSTER COVER LH
1. Remove the screw.
2. Detach the 3 claws in the order shown in the illustration, and then remove the cover.
REMOVE RECLINING ADJUSTER COVER RH
1. Remove the screw.
2. Detach the 5 claws in the order shown in the illustration, and then remove the cover.
REMOVE REAR SEAT REAR BRACKET COVER REAR
1. Detach the 2 claws and cover.
REMOVE REAR NO. 3 SEAT LEG COVER LH
1. Using a screwdriver, remove the spring of the seat stay ball-joint.
2. Disconnect the seat stay.
3. Remove the 2 screws and cover.
REMOVE NO. 2 SEAT LEG COVER NO. 2
1. Remove the screw and seat leg cover.
REMOVE 3RD SEAT LINK SUB-ASSEMBLY LH
1. Remove the bolt, nut and seat link.
REMOVE 3RD SEAT CUSHION LOCK COVER
1. Detach the 4 claws and remove the 2 covers.
REMOVE REAR SEAT CUSHION UNDER COVER LH
1. Detach the 16 claws.
2. Remove the 7 screws and cover.
REMOVE NO. 3 SEAT FRONT BRACKET COVER LH
1. Detach the 4 claws and remove the cover.
REMOVE NO. 3 SEAT LEG COVER NO. 2
1. Remove the 2 screws.
2. Detach the 4 claws and remove the cover.
REMOVE REAR SEAT LOCK COVER LH
1. Remove the 2 screws.
2. Detach the 2 clamps and remove the 2 covers.
REMOVE SEAT STAND FRAME CAP
Text in Illustration

*1 Protective Tape
1. Using a screwdriver, detach the 2 claws and remove the stand frame cap.
  
  Tech Tips
  
  Tape the screwdriver tip before use.
REMOVE SEAT CUSHION LOCK RELEASE LEVER ASSEMBLY LH
1. Remove the screw.
2. Detach the claw and remove the release lever.
3. Detach the cable clamp and disconnect the cable.
REMOVE REAR CENTER SEAT INNER BELT LH (w/ Rear Center Seat Headrest)
1. Remove the nut and belt.
  
  Tech Tips
  
  The rear No. 2 seat inner belt is fixed with the same nut as the rear seat inner belt. Therefore, it becomes disconnected when the nut is removed.
REMOVE REAR CENTER SEAT INNER BELT RH (w/ Rear Center Seat Headrest)
1. Remove the belt.
REMOVE REAR NO. 2 SEAT INNER BELT SUB-ASSEMBLY
1. Remove the nut and belt.
  
  Tech Tips
  
  The rear No. 2 seat inner belt is fixed with the same nut as the rear seat outer belt. Therefore, it becomes disconnected when the nut is removed.
REMOVE REAR SEAT CUSHION CARPET
1. Cut off the tack pins which fasten the seat cushion carpet to the seat cushion pad, and then remove the seat cushion carpet from the seat cushion pad.
REMOVE CAP
1. Detach the 4 claws and remove the 2 caps.
REMOVE NO. 2 BOTTLE HOLDER
1. Remove the 2 screws and No. 2 bottle holder.
REMOVE SEAT CUSHION COVER WITH PAD
REMOVE NO. 3 SEAT CUSHION PAD LH
REMOVE NO. 3 SEAT CUSHION COVER SUB-ASSEMBLY LH
1. w/o Bottle Holder:
  1. Text in Illustration
    
    *1 Fastening Tape
    
    Remove the hog rings.
  2. Detach the fastening tape and remove the seat cushion cover.
2. w/ Bottle Holder:
  1. Text in Illustration
    
    *1 Fastening Tape
    
    Remove the hog rings.
  2. Detach the 3 fastening tapes and remove the seat cushion cover.
REMOVE NO. 2 SEAT STAY SUB-ASSEMBLY
1. Remove the bolt and seat stay.
REMOVE NO. 3 FOLD SEAT LOCK CONTROL CABLE ASSEMBLY
1. Detach the 2 cable clamps and disconnect the 2 cables.
2. Detach the 2 clamps and remove the cable.
REMOVE REAR NO. 2 SEATBACK CUSHION
1. Remove the screw and seatback cushion.
REMOVE REAR LOWER SEATBACK LOCK BEZEL
1. Detach the 3 claws and clip, and then remove the seatback lock bezel.
REMOVE REAR SEAT HINGE PAWL GUIDE
1. Detach the 5 claws and remove the guide.
REMOVE REAR SEAT HINGE PAWL GUIDE
1. Remove the screw and guide.
REMOVE REAR SEAT HEADREST ASSEMBLY (w/ Folding Headrest)
Text in Illustration

*1 Protective Tape
1. While releasing the lock inside the headrest support with a screwdriver, remove the headrest.
  
  Tech Tips
  
  Tape the screwdriver tip before use.
REMOVE REAR SEAT HEADREST ASSEMBLY (w/o Folding Headrest)
REMOVE REAR SEAT HEADREST HANDLE
1. Remove the snap ring and headrest handle.
REMOVE SEATBACK COVER WITH PAD
1. LH Side:
  1. w/ Rear Center Headrest:
    
    Open the fastener.
    
    Detach the 2 hooks.
    
    Pull out the center headrest storage bag.
    
    Remove the rear seat protector.
    
    Detach the 8 claws and remove the 4 headrest supports.
  2. w/o Rear Center Headrest:
    
    Detach the hook.
    
    Remove the rear seat protector.
    
    Detach the 4 claws and remove the 2 headrest supports.
2. RH Side:
  1. Detach the hook.
  2. Remove the rear seat protector.
  3. Detach the 4 claws and remove the 2 headrest supports.
3. Remove the hog ring and seatback cover with pad.
REMOVE NO. 3 SEATBACK COVER SUB-ASSEMBLY LH
1. Remove the hog rings and seatback cover.
REMOVE REAR INNER SEAT RECLINING COVER LH
1. Remove the screw.
2. Detach the claw and remove the cover.
REMOVE REAR INNER SEAT RECLINING COVER RH
1. Remove the screw.
2. Detach the claw and remove the cover.
REMOVE REAR SEAT LOCK CONTROL CABLE
1. Detach the 2 cable clamps and disconnect the 2 cables.
2. Detach the 2 clamps and remove the lock control cable.
REMOVE REAR SEATBACK LOCK STRIKER ASSEMBLY LH
1. Remove the 2 nuts and lock striker.
REMOVE REAR NO. 2 SEATBACK COVER LH
1. Detach the 3 claws and remove the cover.
REMOVE REAR SEATBACK LOCK STRIKER COVER LH
1. Detach the 2 clamps and remove the cover.
REMOVE NO. 2 SEAT RECLINING RELEASE HANDLE SUB-ASSEMBLY
1. Remove the bolt and release handle.