FRONT SEAT ASSEMBLY (for Power Seat) REASSEMBLY

CAUTION:

Wear protective gloves. Sharp areas on the parts may injure your hands.

Tech Tips


  • Use the same procedure for RHD and LHD vehicles.

  • The procedure listed below is for LHD vehicles.

  • Use the same procedure for the RH and LH sides.

  • The procedure listed below is for the LH side.

  • A bolt without a torque specification is shown in the standard bolt chart Click here.


  1. INSTALL FRONT SEAT WIRE LH


    1. Attach the claw to install the front seat wire LH.

    2. Attach the wire harness clamps and connect the connectors.

  2. INSTALL FRONT SEAT AIRBAG ASSEMBLY LH

    CAUTION:

    Make sure that the seat frame assembly is not deformed. If it is, replace it with a new one.


    1. A015D6T

      Install the front seat airbag assembly with 2 nuts.

      Torque:
      5.5 N*m  { 56 kgf*cm, 49 in.*lbf }

    2. Attach the 2 clamps to connect the wire harness.

    3. A0155HN

      Attach the 5 clamps to connect the wire harness.

  3. INSTALL SEAT POSITION SENSOR (for Driver Side)


    1. Check that the ignition switch is off.

    2. Check that the cable is disconnected from the battery negative (-) terminal.

      CAUTION:

      Wait at least 90 seconds after disconnecting the cable from the negative (-) battery terminal to disable the SRS system.

    3. A015C3NE04

      Using a 1.0 mm (0.0393 in.) feeler gauge, install the seat position sensor.

      Note


      • If the seat position sensor has been dropped, or there are any cracks, dents or other defects in the case or connector, replace the seat position sensor with a new one.

      • When installing the seat position sensor, be careful that the SRS wiring does not interfere with other parts and that it is not pinched between other parts.

      Tech Tips

      Be sure that the clearance between the seat position sensor and the seat rail is within 0.6 to 1.4 mm (0.0236 to 0.0551 in.).

    4. Using a T30 "TORX" socket wrench, install the seat position sensor with the screw.

      Torque:
      8.0 N*m  { 82 kgf*cm, 71 in.*lbf }

    5. Make sure that the clearance between the seat position sensor and the seat rail is within 0.6 to 1.4 mm (0.0236 to 0.0551 in.).

    6. Check that there is no looseness in the installation parts of the seat position sensor.

    7. Connect the connector.

    8. Install the seat slide position sensor protector to the seat position sensor.

  4. INSTALL SEAT FRAME SET BRACKET SUB-ASSEMBLY (w/ Climate Control Seat System)

    A0156R8

    1. Attach the 4 hooks to install the seat frame set bracket sub-assembly.

  5. INSTALL NO. 1 AIR FILTER (w/ Climate Control Seat System)

    A015B61

    1. Rotate the No. 1 air filter clockwise to attach the claws and install it.

  6. INSTALL SEAT CLIMATE CONTROL BLOWER LH (w/ Climate Control Seat System)

    A015BSJ

    1. Install the seat climate control blower LH with the nut.

    2. Attach the wire harness clamp.

    3. A015B4D

      Install the 2 bolts and connect the connector.

  7. INSTALL SEAT CLIMATE CONTROL CONTROLLER LH (w/ Climate Control Seat System, for Seat Cushion)

    A015A71

    1. Install the seat climate control controller LH with the 2 screws.

    2. Attach the wire harness clamp.

    3. A0157OU

      Attach the 4 claws to connect the seat climate control blower LH.

  8. INSTALL SEAT CLIMATE CONTROL ECU (w/ Climate Control Seat System)

    A0158C8

    1. Attach the claw to install the seat climate control ECU.

    2. Connect the connector.

  9. INSTALL SEAT HEATER CONTROL SUB-ASSEMBLY (w/ Seat Heater System)

    A0159TI

    1. Attach the claw to install the seat heater control sub-assembly.

    2. Attach the wire harness clamp and connect the connector.

  10. INSTALL FRONT LOWER SEAT CUSHION SHIELD LH

    A0157XK

    1. Attach the hook to install the front lower seat cushion shield LH.

    2. Install the screw.

  11. INSTALL FRONT LOWER SEAT CUSHION SHIELD RH


    1. Attach the hook to install the front lower seat cushion shield RH.

    2. Install the screw.

  12. INSTALL UPPER ACTIVE HEADREST UNIT

    A015B4T

    1. Install the upper active headrest unit with the 4 nuts.

      Torque:
      14 N*m  { 143 kgf*cm, 10 ft.*lbf }

  13. INSTALL LOWER ACTIVE HEADREST UNIT

    A01598M

    1. Install the lower active headrest unit with the 2 nuts.

      Torque:
      5.0 N*m  { 51 kgf*cm, 44 in.*lbf }
    2. A0155TU

      Attach the clamp.

    3. Connect the active headrest cable to the upper active headrest unit with the nut.

      Torque:
      5.0 N*m  { 51 kgf*cm, 44 in.*lbf }

  14. INSTALL BUSH (for Driver Side)


    1. A0159H3

      Attach the 3 claws to install the bush.

  15. INSTALL LUMBAR SUPPORT ADJUSTER ASSEMBLY LH (for Driver Side)


    1. A015561

      Install the lumbar support adjuster LH with the 2 screws.

    2. Connect the connector.

    3. A015DVRE01
      Text in Illustration
      *1 Cable Clamp
      *2 Hook

      Attach the 4 hooks to install the seatback spring.

    4. Install the 4 springs.

    5. Connect the active headrest cable to the seatback spring with the cable clamp.

  16. INSTALL OUTSIDE RECLINING ADJUSTER COVER LH

    A015CDN

    1. Attach the claw to install the outside reclining adjuster cover LH.

    2. Install the screw.

  17. INSTALL OUTSIDE RECLINING ADJUSTER COVER RH


    1. Attach the claw to install the outside reclining adjuster cover RH.

    2. Install the screw.

  18. INSTALL INSIDE RECLINING ADJUSTER COVER LH

    A015DBB

    1. Attach the claw to install the inside reclining adjuster cover LH.

    2. Install the 2 screws.

    3. Attach the wire harness clamp.

  19. INSTALL INSIDE RECLINING ADJUSTER COVER RH


    1. Attach the claw to install the inside reclining adjuster cover RH.

    2. Install the 2 screws.

    3. Attach the wire harness clamp.

  20. INSTALL FRONT SEATBACK PROTECTOR

    A015CB8E01
    Text in Illustration
    *1 Double-sided tape

    1. Apply double-sided tape as shown in the illustration.

    2. Install the front seatback protector.

  21. INSTALL FRONT SEATBACK HEATER ASSEMBLY LH (w/ Seat Heater System)


    1. Set the seatback heater with the name stamp side facing the front separate type seatback cover.

    2. w/o Climate Control Seat System:

      Install the front seatback heater assembly LH to the front separate type seatback cover with new tack pins.

      A0156MHE02
      Text in Illustration
      *1 Tack Pin *2 Front Separate Type Seatback Cover
      *3 Front Seatback Heater Assembly LH *4 Name Stamp

    3. w/ Climate Control Seat System:

      Install the front seatback heater assembly LH to the front separate type seatback cover with new tack pins.

      A015E67E01
      Text in Illustration
      *1 Tack Pin *2 Front Separate Type Seatback Cover
      *3 Front Seatback Heater Assembly LH *4 Name Stamp

  22. INSTALL FRONT SEPARATE TYPE SEATBACK COVER


    1. A015631E02
      Text in Illustration
      *1 Hog Ring Pliers
      *2 Fastening Tape

      Attach the fastening tape to install the front separate type seatback cover.

    2. Using hog ring pliers, install new hog rings.

      Note


      • Be careful not to damage the cover.

      • When installing the hog rings, avoid wrinkling the cover.

    3. A015CDTE01
      Text in Illustration
      *1 Seatback Cover Bracket

      Pass the seatback cover bracket through the hole of the front separate type seatback pad.

  23. INSTALL FRONT SEPARATE TYPE SEATBACK COVER (w/ Climate Control Seat System)


    1. A015DM8E01
      Text in Illustration
      *1 Hog Ring Pliers

      Using hog ring pliers, install the front separate type seatback cover to the front separate type seatback pad with new hog rings.

      Note


      • Be careful not to damage the cover.

      • When installing the hog rings, avoid wrinkling the cover.

    2. A015CDTE01
      Text in Illustration
      *1 Seatback Cover Bracket

      Pass the seatback cover bracket through the hole of the front separate type seatback pad.

  24. INSTALL SEATBACK COVER WITH PAD

    A0155XCE01
    Text in Illustration
    *1 Hog Ring
    *2 Hog Ring Pliers

    1. Attach the hooks to install the seatback cover with pad.

    2. A015APXE01
      Text in Illustration
      *1 Seatback Cover Bracket

      Attach the seatback cover bracket with the nut.

      Torque:
      5.0 N*m  { 51 kgf*cm, 44 in.*lbf }

      CAUTION:

      After the seatback cover with pad is installed, make sure the seatback cover bracket is not twisted.

    3. Using hog ring pliers, install new hog rings.

      Note

      Be careful not to damage the cover.

  25. INSTALL FRONT SEAT HEADREST SUPPORT

    A01568X

    1. Attach the 4 claws to install the 2 front seat headrest supports.

  26. INSTALL SEAT CLIMATE CONTROL CONTROLLER LH (w/ Climate Control Seat System, for Seatback)

    A0155SG

    1. Attach the 4 hooks to install the seat climate control controller LH.

    2. Attach the 2 claws to connect the seat climate control blower LH.

  27. INSTALL FRONT SEATBACK BOARD SUB-ASSEMBLY LH

    A01590O

    1. Move the front seatback board sub-assembly in the direction of the arrow to attach the 2 hooks and install it.

    2. Install the 2 screws.

  28. INSTALL FRONT SEAT CUSHION HEATER ASSEMBLY LH (w/ Seat Heater System)


    1. Set the front seat cushion heater assembly LH with the name stamp side facing the front separate type seat cushion cover.

    2. w/o Climate Control Seat System:

      Install the front seat cushion heater assembly LH to the front separate type seat cushion cover with new tack pins.

      A015D9BE02
      Text in Illustration
      *1 Tack Pin *2 Front Separate Type Seat Cushion Cover
      *3 Front Seat Cushion Heater Assembly LH *4 Name Stamp

    3. w/ Climate Control Seat System:

      Install the front seat cushion heater assembly LH to the front separate type seat cushion cover with new tack pins.

      A015B53E01
      Text in Illustration
      *1 Tack Pin *2 Front Separate Type Seat Cushion Cover
      *3 Front Seat Cushion Heater Assembly LH *4 Name Stamp

  29. INSTALL FRONT SEPARATE TYPE SEAT CUSHION COVER

    A015AB6E02
    Text in Illustration
    *1 Hog Ring Pliers

    1. Using hog ring pliers, install the front separate type seat cushion cover to the front separate type seat cushion pad with new hog rings.

      Note


      • Be careful not to damage the cover.

      • When installing the hog rings, avoid wrinkling the cover.

  30. INSTALL SEAT CUSHION COVER WITH PAD


    1. Set the seat cushion cover with pad in place.

    2. A015ADQ

      Attach the hooks to install the seat cushion cover with pad.

    3. Bend the 2 seat frame claws downward.

    4. for Front Passenger Side:


      1. A0157NX

        Attach the 2 clamps to connect the connector holder.

      2. Connect the connector.

    5. w/o Climate Control Seat System:


      1. A015CS8

        Connect the connector and attach the wire harness clamp.

      2. A015DQN

        Connect the connector and attach the 2 wire harness clamps.

    6. w/ Climate Control Seat System:


      1. A015B5P

        Attach the wire harness clamp.

      2. A015CAP

        Connect the 2 connectors and attach the 4 wire harness clamps.

    7. A0156MR

      Install the 2 clips.

  31. INSTALL FRONT POWER SEAT SWITCH LH

    A01573W

    1. Install the front power seat switch LH with the 3 screws.

    2. w/ Seat Position Memory System:

      Connect the 2 connectors.

    3. w/o Seat Position Memory System:

      Connect the connector.

  32. INSTALL FRONT INNER SEAT CUSHION SHIELD LH

    A015D8W

    1. Attach the 2 claws and clip to install the front inner seat cushion shield LH.

    2. Install the screw.

  33. INSTALL FRONT SEAT INNER BELT ASSEMBLY LH

    A015AI8E01

    1. Install the front seat inner belt assembly with the nut.

      Torque:
      42 N*m  { 428 kgf*cm, 31 ft.*lbf }

      Note

      Do not allow the anchor part of the front seat inner belt assembly to overlap the protruding parts of the front seat adjuster.

    2. Connect the connectors and attach the clamps.

  34. INSTALL LUMBAR SWITCH (for Driver Side)

    A0156DM

    1. Install the lumbar switch to the front seat cushion shield LH with the 2 screws.

  35. INSTALL FRONT INNER NO. 1 SEAT CUSHION SHIELD LH

    A0159RQ

    1. Attach the claw to install the front inner No. 1 cushion shield LH to the front seat cushion shield LH.

    2. Install the screw.

  36. INSTALL FRONT SEAT CUSHION SHIELD LH


    1. for Driver Side:

      Connect the connector.

    2. A01597V

      Attach the 2 claws to install the front seat cushion shield LH together with the front inner No. 1 cushion shield LH.

    3. Install the 3 screws.

    4. A015BJU

      Connect the 2 rubber bands.

    5. Install the 2 screws.

  37. INSTALL RECLINING POWER SEAT SWITCH KNOB

    A015CTQ

    1. Attach the 2 claws to install the reclining power seat switch knob.

  38. INSTALL SLIDE AND VERTICAL POWER SEAT SWITCH KNOB

    A0158S6

    1. Attach the 2 claws to install the slide and vertical power seat switch knob.