REAR NO. 1 SEAT ASSEMBLY (for 60/40 Split Seat Type 60 Side) REASSEMBLY

CAUTION:

Wear protective gloves. Sharp areas on the parts may injure your hands.

Tech Tips


  • Use the same procedure for RHD and LHD vehicles.

  • The procedure listed below is for LHD vehicles.


  1. INSTALL REAR SEAT LOCK CONTROL LEVER LH

    A015AP4

    1. Install the lock control lever with the bolt.

      Torque:
      13 N*m  { 133 kgf*cm, 10 ft.*lbf }

  2. INSTALL REAR SEAT CUSHION FRAME SUB-ASSEMBLY LH

    A015B3F

    1. Temporarily install the seat cushion frame with the 5 nuts and bolt.

    2. Tighten the 5 nuts.

      Torque:
      42 N*m  { 428 kgf*cm, 31 ft.*lbf }

    3. Using a T40 "TORX" socket, tighten the bolt.

      Torque:
      21 N*m  { 214 kgf*cm, 15 ft.*lbf }

  3. INSTALL NO. 1 SEAT LEG ASSEMBLY LH

    A01579H

    1. Using a T40 "TORX" socket, install the seat leg assembly with the 2 bolts.

      Torque:
      21 N*m  { 214 kgf*cm, 15 ft.*lbf }

  4. INSTALL REAR SEAT INNER BELT ASSEMBLY

    A015D7QE01

    1. Install the seat belt with the bolt.

      Torque:
      42 N*m  { 428 kgf*cm, 31 ft.*lbf }

      Note

      The anchor part of the seat belt must not overlap the protruding part.

  5. INSTALL SEAT HEATER CONTROL SUB-ASSEMBLY LH (w/ Seat Heater System)

    A0157XZ

    1. Attach the 2 claws to install the seat heater control.

  6. INSTALL REAR SEAT CUSHION HOLDER BRACKET LH (w/ Seat Heater System)

    A015CMH

    1. Install the holder bracket with the 2 screws.

    2. Connect the seat wire connector.

  7. INSTALL REAR NO. 1 SEAT LOCK CABLE ASSEMBLY


    1. A015D79E01

      Attach the clamp to install the seat lock cable.

    2. Attach the 3 cable clamps to connect the 3 cables.

    3. Connect the cable and install a new cable tie.

    4. A01577Q

      Install the lower seat track bracket with the 2 nuts.

      Torque:
      21 N*m  { 214 kgf*cm, 15 ft.*lbf }

  8. INSTALL FOLD SEAT LOCK CONTROL CABLE SUB-ASSEMBLY

    A015980

    1. Install the 2 fold seat lock control cables.

    2. Attach the 2 cable clamps to connect the 2 cables.

  9. INSTALL REAR SEATBACK FRAME SUB-ASSEMBLY LH


    1. A0158A6

      Install the lower seatback cover.

    2. A015D8O

      Temporarily install the seatback frame with the 4 bolts.

    3. LH Side:

      Using a T40 "TORX" socket, tighten the 2 bolts.

      Torque:
      42 N*m  { 428 kgf*cm, 31 ft.*lbf }

    4. RH Side:

      Using a T55 "TORX" socket, tighten the 2 bolts.

      Torque:
      42 N*m  { 428 kgf*cm, 31 ft.*lbf }

  10. INSTALL NO. 2 FOLD SEAT LOCK CONTROL CABLE ASSEMBLY

    A015BZU

    1. Attach the clamp to install the lock control cable.

    2. Attach the 2 cable clamps to connect the cable.

  11. INSTALL RECLINING ADJUSTING CABLE ASSEMBLY LH

    A0157IE

    1. Attach the clamp to install the adjusting cable.

    2. Attach the 2 cable clamps to connect the cable.

  12. INSTALL NO. 1 SEAT 3 POINT TYPE BELT ASSEMBLY LH

    A0156JIE01

    1. Install the belt with the nut labeled A.

      Torque:
      42 N*m  { 428 kgf*cm, 31 ft.*lbf }

    2. Install the belt sensor with the 3 nuts labeled B.

  13. INSTALL REAR SEAT SHOULDER BELT HOLE COVER LH

    A0159A2

    1. Install the seat belt as shown in the illustration.

    2. A015AWY

      Attach the 3 claws to install the shoulder belt hole cover.

  14. INSTALL REAR LOWER SEATBACK COVER SUB-ASSEMBLY LH

    A0159PG

    1. Attach the 4 claws to install the cover.

    2. Install the 4 screws.

  15. INSTALL REAR SEATBACK HINGE COVER LH

    A0155AM

    1. Attach the claw to install the cover.

    2. Install the screw.

  16. INSTALL REAR NO. 1 SEAT RECLINING COVER RH

    A0156C8

    1. Attach the claw to install the cover.

    2. Install the screw.

  17. INSTALL REAR NO. 2 SEAT RECLINING COVER LH

    A015DO8

    1. Attach the clamp to install the cover.

    2. Install the screw.

  18. INSTALL REAR SEAT RECLINING COVER LH

    A015AOA

    1. Attach the claw to install the cover.

    2. Install the screw.

  19. INSTALL CUP HOLDER ASSEMBLY (w/ Center Armrest)


    1. A015BNE

      Attach the 2 clips to install the cup holder.

    2. A0159K6

      Install the 2 screws.

  20. INSTALL NO. 1 SEAT ARMREST PLATE (w/ Center Armrest)

    A0155XW

    1. Attach the 2 claws and 4 clips to install the 2 armrest plates.

  21. INSTALL REAR CENTER SEAT HEADREST ASSEMBLY (w/ Center Armrest)

  22. INSTALL REAR CENTER SEAT ARMREST ASSEMBLY (w/ Center Armrest)

    A015DOV

    1. Using a T40 "TORX" socket, install the center seat armrest with the 2 bolts.

      Torque:
      42 N*m  { 428 kgf*cm, 31 ft.*lbf }

  23. INSTALL SEATBACK STOPPER PLATE


    1. w/ Center Armrest:


      1. Install the bush to the stopper plate.

      2. A015DSR

        Temporarily install the stopper plate with the 3 bolts.

      3. Using a T40 "TORX" socket, tighten the 2 bolts.

        Torque:
        42 N*m  { 428 kgf*cm, 31 ft.*lbf }

      4. Tighten the bolt.

        Torque:
        15 N*m  { 153 kgf*cm, 11 ft.*lbf }

    2. w/o Center Armrest:


      1. Install the bush to the stopper plate.

      2. A01590P

        Temporarily install the stopper plate with the 3 bolts.

      3. Using a T40 "TORX" socket, tighten the 2 bolts.

        Torque:
        42 N*m  { 428 kgf*cm, 31 ft.*lbf }

      4. Tighten the bolt.

        Torque:
        15 N*m  { 153 kgf*cm, 11 ft.*lbf }

  24. INSTALL REAR SEATBACK HEATER ASSEMBLY (w/ Seat Heater System)


    1. Set the seatback heater with the name stamp side facing the seatback cover.

    2. Install the seatback heater with new tack pins.

      A015DFIE01

  25. INSTALL REAR SEPARATE TYPE SEATBACK COVER


    1. A0157DUE01

      w/ Center Armrest:

      Using hog ring pliers, install the seatback cover with new hog rings.

      Note


      • Be careful not to damage the cover.

      • When installing the hog rings, avoid wrinkling the cover.

    2. A0158DPE01

      w/o Center Armrest:

      Using hog ring pliers, install the seatback cover with new hog rings.

      Note


      • Be careful not to damage the cover.

      • When installing the hog rings, avoid wrinkling the cover.

    3. A015DQ5

      w/ Rear Seat Side Airbag:

      Connect the seatback cover bracket to the seatback pad.

  26. INSTALL SEATBACK COVER WITH PAD


    1. Install the seatback cover with pad.

    2. A015BML

      w/ Center Armrest:

      Pull out the seat belt.

    3. A0158Z6

      w/o Center Armrest:

      Pull out the seat belt.

    4. w/ Rear Seat Side Airbag:

      Pass the side airbag wire harness through the hole in the seatback.

    5. w/ Seat Heater System:

      Pass the seatback heater wire harness through the hole in the seatback.


      1. A015APP
      2. A015AWWE01

        Connect the seatback heater wire harness and install a new cable tie.

    6. A0159P8

      w/ Rear Seat Side Airbag:

      Install the seatback cover bracket to the seat frame with the cap nut.

      Torque:
      5.5 N*m  { 56 kgf*cm, 49 in.*lbf }

      Note

      After the seatback trim cover is assembled, make sure the side airbag strap is not twisted.

    7. A0158CZE01

      w/ Center Armrest:

      Using hog ring pliers, install new hog rings to the seatback frame.

    8. A0159WZE01

      w/o Center Armrest:

      Using hog ring pliers, install new hog rings to the seatback frame.

  27. INSTALL REAR SEAT SHOULDER BELT HOLE COVER LH

    A0159WD

    1. Attach the 4 claws to install the cover.

    2. Install the screw.

  28. INSTALL SHOULDER BELT ANCHOR COVER

    A0158V0

    1. Attach the 2 claws to install the cover.

  29. INSTALL REAR NO. 1 SEAT HEADREST SUPPORT ASSEMBLY


    1. A015C63

      w/ Center Armrest:

      Attach the 4 claws to install the 2 supports.

    2. A01567O

      w/o Center Armrest:

      Attach the 8 claws to install the 4 supports.

  30. INSTALL REAR SEAT HEADREST ASSEMBLY

  31. INSTALL REAR SEATBACK BOARD SUB-ASSEMBLY LH


    1. A0158HQ

      w/ Center Armrest:


      1. Push the board down to attach the 2 claws on the bottom.

      2. Attach the 2 claws on the top of the board to install it.

    2. A0159XU

      w/o Center Armrest:


      1. Push the board down to attach the 3 claws on the bottom.

      2. Attach the 3 claws on the top of the board to install it.

  32. INSTALL REAR SEATBACK COVER

    A0158JU

    1. Attach the 4 claws to install the cover.

  33. INSTALL REAR SEAT CUSHION HEATER ASSEMBLY (w/ Seat Heater System)


    1. Set the seat cushion heater with the name stamp side facing the seat cushion cover.

    2. Install the seat cushion heater with new tack pins.

      A015CH2E01

  34. INSTALL REAR SEPARATE TYPE SEAT CUSHION COVER

    A015CUWE01

    1. Using hog ring pliers, install the seat cushion cover to the seat cushion pad with new hog rings.

      Note


      • Be careful not to damage the cover.

      • When installing the hog rings, avoid wrinkling the cover.

    2. A015CKXE01

      Attach the 3 pieces of fastening tape.

  35. INSTALL SEAT CUSHION COVER WITH PAD


    1. Install the seat cushion cover with pad.

    2. w/ Rear Seat Side Airbag:

      Pass the side airbag wire harness through the hole in the seat cushion.

    3. w/ Seat Heater System:


      1. A015BDM

        Pass the seatback heater wire harness through the hole in the seat cushion.

      2. A015DOT

        Connect the 2 seat heater connectors.

    4. w/ Rear Seat Side Airbag:

      Attach the side airbag wire harness clamps.

  36. CONNECT NO. 1 SEAT 3 POINT TYPE BELT ASSEMBLY LH

    A0156NAE01

    1. Connect the belt anchor.

      Note

      Do not overlap the anchor part of the seat belt and protruding parts of the vehicle body.

  37. INSTALL REAR NO. 1 SEAT INNER BELT ASSEMBLY LH

    A0158WYE01

    1. Install the belt with the bolt.

      Torque:
      42 N*m  { 428 kgf*cm, 31 ft.*lbf }

      Note

      Do not overlap the anchor part of the seat belt and protruding parts of the vehicle body.

      Tech Tips

      The No. 1 seat 3 point type belt anchor is fixed with the same bolt as the rear No. 1 seat inner belt LH. Therefore, connect it when installing the rear No. 1 seat inner belt LH.

  38. INSTALL FOLD SEAT LOCK CONTROL CABLE SUB-ASSEMBLY

  39. INSTALL REAR SEAT TRACK HANDLE SUB-ASSEMBLY


    1. A0157BR

      Attach the cable clamp to connect the cable.

    2. A0159IZ

      Attach the 2 cable clamps to connect the 2 cables.

    3. A0157IS

      Install the seat track handle with the 2 screws.

  40. INSTALL REAR SEAT UNDER TRAY COVER LH

    A01585Q

    1. Attach the 4 claws to install the cover.

    2. Install the 2 screws.

  41. INSTALL REAR SEAT CUSHION COVER RH

    A015D52

    1. Attach the 2 claws to install the cover.

    2. Install the 4 screws.

  42. INSTALL NO. 1 SEAT CUSHION PLATE

    A015B2F

    1. Attach the 3 claws to install the seat cushion plate.

  43. INSTALL REAR UNDER SIDE COVER LH

    A015CRP

    1. Attach the 2 claws and 2 clips to install the cover.

    2. Install the 5 screws.

    3. A0155YN

      Attach the 10 claws.

  44. INSTALL REAR SEATBACK STAY COVER LH

    A015E3G

    1. Attach the 2 claws to install the cover.

    2. Install the screw.

  45. INSTALL SEAT BELT ANCHOR COVER CAP


    1. A0159WX

      Install the anchor cover cap with the screw.

    2. A015C6J

      Attach the claw to close the cap.

  46. INSTALL REAR NO. 1 SEAT HINGE SUB-ASSEMBLY RH

    A015AE2

    1. Install the hinge with the 2 nuts.

      Torque:
      42 N*m  { 428 kgf*cm, 31 ft.*lbf }

  47. INSTALL REAR NO. 1 SEAT HINGE SUB-ASSEMBLY LH


    1. A0155TF

      Attach the cable clamp to connect the cable.

    2. A0157X7

      Install the hinge with the 2 nuts.

      Torque:
      42 N*m  { 428 kgf*cm, 31 ft.*lbf }

    3. w/ Rear Seat Side Airbag:

      Attach the wire harness clamp.

    4. w/ Seat Heater System:

      Attach the wire harness clamp.

  48. INSTALL REAR NO. 2 SEAT PROTECTOR


    1. Install the wire harness, and attach 2 claws to close the protector.

    2. A015BO6

      Attach the claw to install the protector to the seat hinge.

    3. Install the clip.

    4. A0155UV

      w/ Rear Seat Side Airbag:

      Attach the claw to install the wire harness connector.

    5. w/ Seat Heater System:

      Attach the claw to install the wire harness connector.

  49. INSTALL REAR SEAT SIDE HINGE MALE COVER RH


    1. A0157HN

      Attach the clip to install the cover.

  50. INSTALL REAR SEAT SIDE HINGE MALE COVER LH


    1. Attach the clip to install the cover.

  51. INSTALL REAR SEAT SIDE HINGE FEMALE COVER


    1. A015CYP

      Attach the 6 claws to install the 2 covers.

  52. INSTALL FOLD SEAT STOPPER BAND ASSEMBLY


    1. Install the fold seat stopper band to the seat leg side cover.

  53. INSTALL REAR NO. 2 SEAT LEG SIDE COVER


    1. A015AUN

      Pass the fold seat stopper band through the seat leg side cover and attach it to the seat cushion frame with the bolt.

    2. A0156BB

      Attach the 4 claws to install the seat leg side cover.

    3. Install the 4 screws.

  54. INSTALL NO. 1 SEAT CUSHION COVER

    A0156QI

    1. Attach the 4 claws to install the 2 covers.

  55. INSTALL UPPER SEAT TRACK RAIL COVER RH

    A0156Z8

    1. Attach the 2 claws to install the cover.

  56. INSTALL UPPER SEAT TRACK RAIL COVER LH

    A01556W

    1. Attach the 2 claws to install the cover.

  57. INSTALL REAR NO. 1 SEAT RECLINING COVER RH

    A015CKY

    1. Attach the 4 claws to install the cover.

    2. Install the 2 screws.

  58. INSTALL REAR NO. 1 SEAT RECLINING COVER LH

    A015B48E01

    1. Attach the 3 claws in the order shown in the illustration to install the cover.

    2. Install the 2 screws.

  59. INSTALL RECLINING ADJUSTER RELEASE HANDLE LH

    A0155T5

    1. Install the release handle with the screw.

  60. INSTALL SEAT ADJUSTER BOLT COVER

    A01554I

    1. Attach the 2 claws to install the cover.