FRONT SEAT SIDE AIRBAG ASSEMBLY (for Power Seat) INSTALLATION

CAUTION:

Wear protective gloves. Sharp areas on the parts may injure your hands.

Tech Tips


  • Use the same procedures for LHD and RHD vehicles.

  • The procedures listed below are for LHD vehicles.


  1. INSTALL FRONT SEAT AIRBAG ASSEMBLY LH

    CAUTION:

    Make sure that the seat frame assembly is not deformed. If it is, replace it with a new one.


    1. A015D6T

      Install the front seat airbag assembly with 2 nuts.

      Torque:
      5.5 N*m  { 56 kgf*cm, 49 in.*lbf }

    2. Attach the 2 clamps to connect the wire harness.

    3. A0155HN

      Attach the 5 clamps to connect the wire harness.

  2. INSTALL SEAT CLIMATE CONTROL CONTROLLER LH (w/ Climate Control Seat System)

    A015A71

    1. Install the seat climate control controller LH with the 2 screws.

    2. Attach the wire harness clamp.

    3. A0157OU

      Attach the 4 claws to connect the seat climate control blower LH.

  3. INSTALL FRONT SEATBACK PROTECTOR (w/ Climate Control Seat System)

    A015CB8E01
    Text in Illustration
    *1 Double-sided tape

    1. Apply double-sided tape as shown in the illustration.

    2. Install the front seatback protector.

  4. INSTALL SEATBACK COVER WITH PAD


    1. A0159VTE02
      Text in Illustration
      *1 Hog Ring

      Remove the hog rings.

    2. A015APXE01
      Text in Illustration
      *1 Seatback Cover Bracket

      Remove the nut and detach the seatback cover bracket.

    3. Detach the hooks and remove the seatback cover with pad.

  5. INSTALL FRONT SEAT HEADREST SUPPORT

    A01568X

    1. Attach the 4 claws to install the 2 front seat headrest supports.

  6. INSTALL FRONT SEATBACK BOARD SUB-ASSEMBLY LH

    A01590O

    1. Move the front seatback board sub-assembly in the direction of the arrow to attach the 2 hooks and install it.

    2. Install the 2 screws.

  7. INSTALL FRONT INNER SEAT CUSHION SHIELD LH

    A015D8W

    1. Attach the 2 claws and clip to install the front inner seat cushion shield LH.

    2. Install the screw.

  8. INSTALL FRONT SEAT INNER BELT ASSEMBLY LH

    A015AI8E01

    1. Install the front seat inner belt assembly with the nut.

      Torque:
      42 N*m  { 428 kgf*cm, 31 ft.*lbf }

      Note

      Do not allow the anchor part of the front seat inner belt assembly to overlap the protruding parts of the front seat adjuster.

    2. Connect the connectors and attach the clamps.

  9. INSTALL FRONT SEAT CUSHION SHIELD LH


    1. for Driver Side:

      Connect the connector.

    2. A01597V

      Attach the 2 claws to install the front seat cushion shield LH together with the front inner No. 1 cushion shield LH.

    3. Install the 3 screws.

    4. A015BJU

      Connect the 2 rubber bands.

    5. Install the 2 screws.

  10. INSTALL RECLINING POWER SEAT SWITCH KNOB

    A015CTQ

    1. Attach the 2 claws to install the reclining power seat switch knob.

  11. INSTALL SLIDE AND VERTICAL POWER SEAT SWITCH KNOB

    A0158S6

    1. Attach the 2 claws to install the slide and vertical power seat switch knob.

  12. INSTALL FRONT SEAT ASSEMBLY LH


    1. Install the front seat assembly LH Click here.