Click here

SFI SYSTEM, Diagnostic DTC:P2237, P2238, P2239, P2240, P2241, P2242, P2252, P2253, P2255, P2256

Click here
Click here Click here
DTC Code DTC Name
P2237 Oxygen (A/F) Sensor Pumping Current Circuit / Open (Bank 1 Sensor 1)
P2238 Oxygen (A/F) Sensor Pumping Current Circuit Low (Bank 1 Sensor 1)
P2239 Oxygen (A/F) Sensor Pumping Current Circuit High (Bank 1 Sensor 1)
P2240 Oxygen (A/F) Sensor Pumping Current Circuit / Open (Bank 2 Sensor 1)
P2241 Oxygen (A/F) Sensor Pumping Current Circuit Low (Bank 2 Sensor 1)
P2242 Oxygen (A/F) Sensor Pumping Current Circuit High (Bank 2 Sensor 1)
P2252 Oxygen (A/F) Sensor Reference Ground Circuit Low (Bank 1 Sensor 1)
P2253 Oxygen (A/F) Sensor Reference Ground Circuit High (Bank 1 Sensor 1)
P2255 Oxygen (A/F) Sensor Reference Ground Circuit Low (Bank 2 Sensor 1)
P2256 Oxygen (A/F) Sensor Reference Ground Circuit High (Bank 2 Sensor 1)
Click here

DESCRIPTION

Refer to DTC P2195 (Click here).

DTC No. DTC Detection Condition Trouble Area

P2237

P2240

 Open in the circuit between terminals AF+ and AF- of the air fuel ratio sensor while the engine is running (2 trip detection logic).

  • Open or short in air fuel ratio sensor (sensor 1) circuit

  • Air fuel ratio sensor (sensor 1)

  • ECM

P2238

P2241

  • Case 1:

Condition (a) or (b) is met for 5.0 seconds or more (2 trip detection logic):

(a) AF+ voltage is 0.5 V or less.

(b) (AF+) - (AF-) is 0.1 V or less.


  • Case 2:

Air fuel ratio sensor admittance is below 0.0074 1/Ω (2 trip detection logic).

  • Open or short in air fuel ratio sensor (sensor 1) circuit

  • Air fuel ratio sensor (sensor 1)

  • ECM

P2239

P2242

 AF+ voltage is higher than 4.5 V for 5.0 seconds or more (2 trip detection logic).

  • Open or short in air fuel ratio sensor (sensor 1) circuit

  • Air fuel ratio sensor (sensor 1)

  • ECM

P2252

P2255

 AF- voltage is 0.5 V or less for 5.0 seconds or more (2 trip detection logic).

  • Open or short in air fuel ratio sensor (sensor 1) circuit

  • Air fuel ratio sensor (sensor 1)

  • ECM

P2253

P2256

 AF- voltage is higher than 4.5 V for 5.0 seconds or more (2 trip detection logic).

  • Open or short in air fuel ratio sensor (sensor 1) circuit

  • Air fuel ratio sensor (sensor 1)

  • ECM
Tip:

  • DTCs P2237, P2238, P2239, P2252 and P2253 indicate malfunctions related to the bank 1 air fuel ratio sensor circuit.

  • DTCs P2240, P2241, P2242, P2255 and P2256 indicate malfunctions related to the bank 2 air fuel ratio sensor circuit.

  • Bank 1 refers to the bank that includes cylinder No. 1.

  • Bank 2 refers to the bank that includes cylinder No. 2.

Click here

MONITOR DESCRIPTION

The air fuel ratio sensor varies its output voltage in proportion to the air-fuel ratio. If the air fuel ratio sensor impedance (alternating current resistance) or output voltage deviates greatly from the standard range, the ECM determines that there is an open or short in the air fuel ratio sensor circuit.

Click here

CONFIRMATION DRIVING PATTERN


  1. Start the engine and wait for 5 minutes or more.

Click here

WIRING DIAGRAM

Refer to DTC P2195 (Click here).

Click here

INSPECTION PROCEDURE

Tip:

  • Read freeze frame data using the GTS. Freeze frame data records the engine condition when malfunctions are detected. When troubleshooting, freeze frame data can help determine if the vehicle was moving or stationary, if the engine was warmed up or not, if the air-fuel ratio was lean or rich, and other data from the time the malfunction occurred.

  • Bank 1 refers to the bank that includes the No. 1 cylinder*.

    *: The No. 1 cylinder is the cylinder which is farthest from the transmission.

  • Bank 2 refers to the bank that does not include the No. 1 cylinder.

  • Sensor 1 refers to the sensor closest to the engine assembly.

  • Sensor 2 refers to the sensor farthest away from the engine assembly.

Click here

PROCEDURE


  1. Click here

    CHECK HARNESS AND CONNECTOR (AIR FUEL RATIO SENSOR - ECM)


    1. Disconnect the air fuel ratio sensor connector.

    2. Disconnect the ECM connector.

    3. Measure the resistance according to the value(s) in the table below.

      Standard Resistance
      Table 1. for LHD
      Tester Connection Condition Specified Condition
      C22-1 (HA1A) - C45-22 (HA1A) Always Below 1 Ω
      C22-3 (A1A+) - C45-126 (A1A+) Always Below 1 Ω
      C22-4 (A1A-) - C45-125 (A1A-) Always Below 1 Ω
      C23-1 (HA2A) - C45-20 (HA2A) Always Below 1 Ω
      C23-3 (A2A+) - C45-103 (A2A+) Always Below 1 Ω
      C23-4 (A2A-) - C45-102 (A2A-) Always Below 1 Ω
      C22-1 (HA1A) or C45-22 (HA1A) - Body ground Always 10 kΩ or higher
      C22-3 (A1A+) or C45-126 (A1A+) - Body ground Always 10 kΩ or higher
      C22-4 (A1A-) or C45-125 (A1A-) - Body ground Always 10 kΩ or higher
      C23-1 (HA2A) or C45-20 (HA2A) - Body ground Always 10 kΩ or higher
      C23-3 (A2A+) or C45-103 (A2A+) - Body ground Always 10 kΩ or higher
      C23-4 (A2A-) or C45-102 (A2A-) - Body ground Always 10 kΩ or higher
      Table 2. for RHD
      Tester Connection Condition Specified Condition
      C22-1 (HA1A) - C46-22 (HA1A) Always Below 1 Ω
      C22-3 (A1A+) - C46-126 (A1A+) Always Below 1 Ω
      C22-4 (A1A-) - C46-125 (A1A-) Always Below 1 Ω
      C23-1 (HA2A) - C46-20 (HA2A) Always Below 1 Ω
      C23-3 (A2A+) - C46-103 (A2A+) Always Below 1 Ω
      C23-4 (A2A-) - C46-102 (A2A-) Always Below 1 Ω
      C22-1 (HA1A) or C46-22 (HA1A) - Body ground Always 10 kΩ or higher
      C22-3 (A1A+) or C46-126 (A1A+) - Body ground Always 10 kΩ or higher
      C22-4 (A1A-) or C46-125 (A1A-) - Body ground Always 10 kΩ or higher
      C23-1 (HA2A) or C46-20 (HA2A) - Body ground Always 10 kΩ or higher
      C23-3 (A2A+) or C46-103 (A2A+) - Body ground Always 10 kΩ or higher
      C23-4 (A2A-) or C46-102 (A2A-) - Body ground Always 10 kΩ or higher

  2. Click here

    REPLACE AIR FUEL RATIO SENSOR


    1. Replace the air fuel ratio sensor (Click here).


  3. Click here

    PERFORM CONFIRMATION DRIVING PATTERN


    1. Drive the vehicle according to Confirmation Driving Pattern.


  4. Click here

    CHECK WHETHER DTC OUTPUT RECURS


    1. Connect the GTS to the DLC3.

    2. Turn the ignition switch to ON and turn the GTS on.

    3. Enter the following menus: Powertrain / Engine and ECT / Trouble Codes / Pending.

    4. Read the pending DTCs.

      Table 3. Result
      Result Proceed to
      No DTC is output A
      P2237, P2238, P2239, P2240, P2241, P2242, P2252, P2253, P2255 or P2256 is output B

  5. Click here

    REPAIR OR REPLACE HARNESS OR CONNECTOR

  6. Click here

    REPLACE ECMClick here

  7. Click here

    END