Click here

FUEL FILTER REPLACEMENT

Click here
Click here Click here
  1. Click here

    DISCHARGE FUEL SYSTEM PRESSURE

    (Click here)

  2. Click here

    PRECAUTION

    Note:

    After turning the ignition switch off, waiting time may be required before disconnecting the cable from the battery terminal. Therefore, make sure to read the disconnecting the cable from the battery terminal notice before proceeding with work (Click here).

  3. Click here

    DISCONNECT CABLE FROM NEGATIVE BATTERY TERMINAL

    Note:

    When disconnecting the cable, some systems need to be initialized after the cable is reconnected (Click here).

  4. Click here

    REMOVE NO. 1 FUEL TUBE PROTECTOR


    1. A0157LV

      Remove the 4 bolts and No. 1 fuel tube protector.

  5. Click here

    DISCONNECT NO. 2 FUEL MAIN TUBE SUB-ASSEMBLY


    1. A015727E03

      Pull up the retainer and disconnect the No. 2 fuel main tube.

      Note:

      • Check for foreign matter in the pipe and around the connector. Clean if necessary. Foreign matter may damage the O-ring or cause leaks in the seal between the pipe and connector.

      • Do not use any tools to separate the pipe and connector.

      • Do not forcefully bend or twist the nylon tube.

      • Check for foreign matter on the pipe seal surface. Clean if necessary.

      • Put the pipe and connector ends in plastic bags to prevent damage and foreign matter contamination.

      • If the pipe and connector are stuck together, pinch the connector between your fingers and turn it carefully to disconnect it.

      Table 1. Text in Illustration
      *1 Retainer
      *2 Nylon Tube
      *3 Pipe
      *4 O-Ring
      *5 Connector
  6. Click here

    DISCONNECT FUEL MAIN TUBE


    1. A015607E03

      Pull up the retainer and disconnect the fuel main tube.

      Note:

      • Check for foreign matter in the pipe and around the connector. Clean if necessary. Foreign matter may damage the O-ring or cause leaks in the seal between the pipe and connector.

      • Do not use any tools to separate the pipe and connector.

      • Do not forcefully bend or twist the nylon tube.

      • Check for foreign matter on the pipe seal surface. Clean if necessary.

      • Put the pipe and connector ends in plastic bags to prevent damage and foreign matter contamination.

      • If the pipe and connector are stuck together, pinch the connector between your fingers and turn it carefully to disconnect it.

      Table 2. Text in Illustration
      *1 Retainer
      *2 Nylon Tube
      *3 Pipe
      *4 O-Ring
      *5 Connector
  7. Click here

    REMOVE FUEL FILTER ASSEMBLY


    1. A015637

      Remove the 2 bolts and fuel filter.

  8. Click here

    INSTALL FUEL FILTER ASSEMBLY


    1. Install the fuel filter with the 2 bolts.

      20 N*m 199 kgf*cm 14 ft.*lbf
  9. Click here

    CONNECT FUEL MAIN TUBE


    1. A0159CSE03

      Connect the fuel main tube and push the retainer.

      Note:

      • Before installing the tube connectors to the pipes, check if there is any damage or foreign matter in the connectors.

      • After the connection, check if the connectors and pipes are securely connected by trying to pull them apart.

      Table 3. Text in Illustration
      *1 Retainer
      *2 Nylon Tube
      *3 Pipe
      *4 O-Ring
      *5 Connector
      Tip:

      Push the parts together firmly until a "click" sound is heard.

  10. Click here

    CONNECT NO. 2 FUEL MAIN TUBE SUB-ASSEMBLY


    1. A0156SOE03

      Connect the No. 2 fuel main tube and push the retainer.

      Note:

      • Before installing the tube connectors to the pipes, check if there is any damage or foreign matter in the connectors.

      • After the connection, check if the connectors and pipes are securely connected by trying to pull them apart.

      Table 4. Text in Illustration
      *1 Retainer
      *2 Nylon Tube
      *3 Pipe
      *4 O-Ring
      *5 Connector
      Tip:

      Push the parts together firmly until a "click" sound is heard.

  11. Click here

    CONNECT CABLE TO NEGATIVE BATTERY TERMINAL

    Note:

    When disconnecting the cable, some systems need to be initialized after the cable is reconnected (Click here).

  12. Click here

    INSPECT FOR FUEL LEAK


    1. Make sure that there are no fuel leaks after performing maintenance on the fuel system.


      1. Connect the GTS to the DLC3.

      2. Turn the ignition switch to ON and turn the GTS on.

        Note:

        Do not start the engine.

      3. Enter the following menus: Powertrain / Engine and ECT / Active Test / Control the Fuel Pump / Speed.

      4. Check that there are no leaks from the fuel system.

        If there are fuel leaks, repair or replace parts as necessary.

      5. Turn the ignition switch off.

      6. Disconnect the GTS from the DLC3.

  13. Click here

    INSTALL NO. 1 FUEL TUBE PROTECTOR


    1. Install the No. 1 fuel tube protector and 4 bolts.

      29 N*m 296 kgf*cm 21 ft.*lbf