ECD SYSTEM (w/ DPF), Diagnostic DTC:P0724

DTC Code DTC Name
P0724 Brake Switch "B" Circuit High

DESCRIPTION

This DTC indicates that the stop light switch remains on. When the stop light switch remains on during GO and STOP driving, the ECM interprets this as a fault in the stop light switch. Then the MIL illuminates and the ECM stores the DTC.

P0724
DTC Detection Drive Pattern DTC Detection Condition Trouble Area
Accelerate the vehicle to 30 km/h (19 mph) or more, depress the brake pedal and decelerate the vehicle to 3 km/h (1.8 mph) or less 5 times.

Stop light switch remains on even when vehicle is driven in GO (30 km/h (19 mph) or more) and STOP (less than 3 km/h (1.8 mph)) pattern 5 times.

(2 trip detection logic)

  • Short in stop light switch signal circuit

  • Stop light switch assembly

  • ECM
Related Data List
DTC No. Data List
P0724 Stop Light Switch

WIRING DIAGRAM

Refer to DTC P0504 Click here.

INSPECTION PROCEDURE

Note


  • Inspect the fuses of circuits related to this system before performing the following inspection procedure.

  • After replacing the ECM, the new ECM needs registration Click here and initialization Click here.

  • After replacing the fuel supply pump assembly, the ECM needs initialization Click here.

  • After replacing an injector assembly, the ECM needs registration Click here.

Tech Tips

Read freeze frame data using the GTS. Freeze frame data records the engine condition when malfunctions are detected. When troubleshooting, freeze frame data can help determine if the vehicle was moving or stationary, if the engine was warmed up or not, and other data from the time the malfunction occurred.

PROCEDURE


  1. READ VALUE USING GTS (STOP LIGHT SWITCH)


    1. Connect the GTS to the DLC3.

    2. Turn the engine switch on (IG).

    3. Enter the following menus: Engine and ECT / Data List / Stop Light Switch.

    4. Read the value displayed on the GTS when the brake pedal is depressed and released.

      OK
      Brake Pedal Display
      Released OFF
      Depressed ON

    OK

    CONFIRM WHETHER MALFUNCTION HAS BEEN SUCCESSFULLY REPAIRED Click here

    NG

    INSPECT STOP LIGHT SWITCH ASSEMBLY Click here

  2. INSPECT STOP LIGHT SWITCH ASSEMBLY


    1. Inspect the stop light switch assembly Click here.


    NG

    REPLACE STOP LIGHT SWITCH ASSEMBLY Click here

    OK

  3. CHECK ECM (STP VOLTAGE)

    A0157VPE04
    Text in Illustration
    *A for LHD
    *B for RHD
    *a Brake Pedal Depressed
    *b Brake Pedal Released
    *c

    Component with harness connected

    (ECM)

    1. Disconnect the ECM connector.

    2. Turn the engine switch on (IG).

    3. Measure the voltage according to the value(s) in the table below.

      Standard Voltage
      for LHD
      Tester Connection Brake Pedal Condition Specified Condition
      A38-13 (STP) - Body ground Released 0 to 3 V
      Depressed 11 to 14 V
      Standard Voltage
      for RHD
      Tester Connection Brake Pedal Condition Specified Condition
      A52-13 (STP) - Body ground Released 0 to 3 V
      Depressed 11 to 14 V

    NG

    REPAIR OR REPLACE HARNESS OR CONNECTOR Click here

    OK

  4. REPLACE ECM


    1. Replace the ECM Click here.


    NEXT

    CONFIRM WHETHER MALFUNCTION HAS BEEN SUCCESSFULLY REPAIRED Click here

  5. REPLACE STOP LIGHT SWITCH ASSEMBLY


    1. Replace the stop light switch assembly Click here.


    NEXT

    CONFIRM WHETHER MALFUNCTION HAS BEEN SUCCESSFULLY REPAIRED Click here

  6. REPAIR OR REPLACE HARNESS OR CONNECTOR


    1. Repair or replace the harness or connector.


    NEXT

  7. CONFIRM WHETHER MALFUNCTION HAS BEEN SUCCESSFULLY REPAIRED


    1. Connect the GTS to the DLC3.

    2. Clear the DTCs Click here.

    3. Turn the engine switch off for 30 seconds or more.

    4. Turn the engine switch on (IG) and turn the GTS on.

    5. Start the engine.

    6. Accelerate the vehicle to 30 km/h (19 mph) or more, depress the brake pedal and decelerate the vehicle to 3 km/h (1.8 mph) or less 5 times or more.

    7. Confirm that the DTC is not output again.

      Tech Tips

      Perform the following procedure using the GTS to determine whether or not the DTC judgment has been carried out.


      1. Enter the following menus: Engine and ECT / Utility / All Readiness.

      2. Input DTC P0724.

      3. Check that STATUS is NORMAL.

        Tech Tips


        • If STATUS is NORMAL, DTC judgment is complete and it can be determined that the system is normal.

        • If STATUS is INCOMPLETE or N/A, DTC judgment is incomplete. Perform the following procedure again 5 times: accelerate the vehicle to 30 km/h (19 mph) or more, depress the brake pedal and decelerate the vehicle to 3 km/h (1.8 mph) or less.


    NEXT

    END