HOOD LOCK CONTROL CABLE ASSEMBLY REMOVAL


  1. REMOVE COOL AIR INTAKE DUCT SEAL


    1. A01G7XF

      Remove the 9 clips and cool air intake duct seal.

  2. REMOVE MILLIMETER WAVE RADAR SENSOR ASSEMBLY (w/ Dynamic Radar Cruise Control System)

    Click here

  3. REMOVE FRONT WHEEL LH (for LHD)

  4. REMOVE FRONT WHEEL OPENING EXTENSION PAD LH (for LHD)

    Tech Tips

    Use the same procedure as for the RH side Click here.

  5. REMOVE FRONT FENDER LINER LH (for LHD)

    Tech Tips

    Use the same procedure as for the RH side Click here.

  6. REMOVE FRONT WHEEL RH (for RHD)

  7. REMOVE FRONT WHEEL OPENING EXTENSION PAD RH (for RHD)


    1. A01G6JK

      Remove the 3 screws and front wheel opening extension pad RH.

  8. REMOVE FRONT FENDER LINER RH (for RHD)


    1. A01G80NE01
      Text in Illustration
      *a 90°

      Using a screwdriver, turn the pin 90 degrees counterclockwise and remove the pin hold clip.

    2. A01G9MQ

      Remove the 4 screws and bolt.

    3. A01G5QS

      Remove the 6 clips.

    4. A01G45N

      Using a 4 mm hexagon wrench, remove the 3 hexagon screws.

    5. Remove the 2 grommets and front fender liner RH.

      Tech Tips

      The grommets need to be replaced with new ones because they will break when they are removed.

  9. REMOVE FRONT DOOR SCUFF PLATE LH (for LHD)


    1. A01G8TA

      Disengage the 10 claws and remove the front door scuff plate LH.

  10. REMOVE COWL SIDE TRIM BOARD LH (for LHD)


    1. A01G75T

      Remove the clip.

    2. Disengage the claw and clip, and remove the cowl side trim board LH.

  11. REMOVE FRONT DOOR SCUFF PLATE RH (for RHD)

    Tech Tips

    Use the same procedure as for the LH side Click here.

  12. REMOVE COWL SIDE TRIM BOARD RH (for RHD)

    Tech Tips

    Use the same procedure as for the LH side Click here.

  13. DISCONNECT HOOD LOCK CONTROL LEVER SUB-ASSEMBLY


    1. A01G4MG

      Disengage the claw and 2 guides to disconnect the hood lock control lever sub-assembly.

  14. REMOVE HOOD LOCK CONTROL LEVER SUB-ASSEMBLY


    1. A01G6UL

      Disconnect the hood lock control cable assembly and remove the hood lock control lever sub-assembly.

  15. REMOVE HOOD LOCK ASSEMBLY (for LHD)


    1. A01G8O0

      Disconnect the connector.

    2. Disengage the clamp.

    3. A01G4U6

      Remove the 3 bolts.

    4. A01G461

      Disconnect the hood lock control cable assembly and remove the hood lock assembly.

  16. REMOVE HOOD LOCK ASSEMBLY (for RHD)


    1. A01G6K8

      Disconnect the connector.

    2. Disengage the clamp.

    3. A01G4L8

      Remove the 3 bolts.

    4. A01G73K

      Disconnect the hood lock control cable assembly and remove the hood lock assembly.

  17. REMOVE HOOD LOCK CONTROL CABLE ASSEMBLY (for LHD)


    1. Using a screwdriver, disengage the 5 clamps and hood cable grommet as shown in the illustration.

      A01G4B6E02
      Text in Illustration
      *1 Hood Lock Control Cable Assembly *2 Washer Hose
      *a Hood Cable Grommet - -

      Tech Tips

      Tape the screwdriver tip before use.

    2. Pull the hood lock control cable assembly from the engine compartment and remove it.

  18. REMOVE HOOD LOCK CONTROL CABLE ASSEMBLY (for RHD)


    1. Using a screwdriver, disengage the 4 clamps and hood cable grommet as shown in the illustration.

      A01G53YE01
      Text in Illustration
      *1 Hood Lock Control Cable Assembly *2 Washer Hose
      *a Hood Cable Grommet - -

      Tech Tips

      Tape the screwdriver tip before use.

    2. Pull the hood lock control cable assembly from the engine compartment and remove it.