REAR AIRBAG SENSOR INSTALLATION

Tech Tips

Use the same procedure for the RH side and LH side.
The procedure listed below is for the LH side.

INSTALL REAR AIRBAG SENSOR

Check that the engine switch is off.
Check that the cable is disconnected from the negative (-) battery terminal.

CAUTION:

Wait at least 90 seconds after disconnecting the cable from the negative (-) battery terminal to disable the SRS system.
Before connecting the connector, check that the position of the white housing lock is correct as shown in the illustration.

Text in Illustration

*a Correct *b Incorrect
Insert the pin (stopper) into the body hole and install the rear airbag sensor to the vehicle body with the bolt.

Torque:

9.0 N*m { 92 kgf*cm, 80 in.*lbf }
Note
- If the rear airbag sensor has been dropped, or there are any cracks, dents or other defects in the case or connector, replace it with a new one.
- When installing the rear airbag sensor, be careful that the SRS wiring does not interfere with or is not pinched between other parts.
- Make sure that the pin (stopper) is securely inserted into the body hole.
- Tighten the bolt while holding the rear airbag sensor because the rear airbag sensor pin (stopper) is easily damaged.

Text in Illustration
*a	Correct	*b	Incorrect

Connect the connector to the rear airbag sensor.

Note

When connecting any airbag connector, take care not to damage the airbag wire harness.

Be sure to engage the connectors until they are locked (when locking, make sure that a click sound can be heard).

Text in Illustration
*1	White housing lock	-	-
*a	Slide	-	-

Tech Tips

When engaged, the white housing lock will slide. Be sure not to hold the white housing lock and part (A), as it may result in an insecure fit.

Check that there is no looseness in the installed parts of the rear airbag sensor.

INSTALL REAR SEAT SIDE GARNISH
1. Engage the 5 claws to install the rear seat side garnish LH.
INSTALL REAR DOOR SCUFF PLATE
1. Engage the 8 claws to install the rear door scuff plate LH.
INSTALL REAR SEATBACK ASSEMBLY
1. Place the rear seatback assembly in the cabin.
  
  Note
  
  Be careful not to damage the vehicle body.
2. Engage the 3 hooks.
3. Connect the rear seat 3 point type outer belt assembly LH, rear seat 3 point type outer belt assembly RH and rear seat inner with center belt assembly LH to the rear seatback assembly.
4. Install the rear seatback assembly with the 4 bolts.
  
  Torque:
  
  18 N*m { 184 kgf*cm, 13 ft.*lbf }
5. Engage the 2 clamps to connect the 2 rear seat airbag assembly wire harnesses.
6. Connect the 2 rear seat airbag assembly connectors.
7. Engage the claw to connect the rear center seat shoulder belt guide.
8. Engage the claw to connect the rear seat shoulder belt guide RH.
9. Engage the claw to connect the rear seat shoulder belt guide LH.
INSTALL REAR SEAT CUSHION ASSEMBLY
1. Place the rear seat cushion assembly in the cabin.
  
  Note
  
  Be careful not to damage the vehicle body.
2. w/ Climate Control Seat System:
  1. Connect the rear seat heater connector.
3. Pass the buckle of the rear seat inner with center belt assembly LH and buckle of the rear seat inner with center belt assembly RH through the rear seat cushion assembly.
4. Text in Illustration
  
  *1 Rear Seatback Hinge Hook
  
  Engage the 2 hooks <B> on rear side of the rear seat cushion assembly to the rear seatback hinge hook.
5. Engage the 2 hooks <A> on the front side of the rear seat cushion assembly to the vehicle body as shown in the illustration.
6. Confirm that the rear seat cushion assembly is firmly installed.
  
  Note
  
  When installing the rear seat cushion assembly, make sure that the seat belt buckles are not under the rear seat cushion assembly.
INSTALL REAR CENTER SEAT HEADREST ASSEMBLY
INSTALL REAR SEAT HEADREST ASSEMBLY
CONNECT CABLE TO NEGATIVE BATTERY TERMINAL

Note

When disconnecting the cable, some systems need to be initialized after the cable is reconnected Click here.
PERFORM DIAGNOSTIC SYSTEM CHECK

Click here
INSPECT SRS WARNING LIGHT

Click here