IMMOBILISER SYSTEM Security Indicator Light Does not Blink

DESCRIPTION


WIRING DIAGRAM

A01G5W0E06

INSPECTION PROCEDURE

Note


  • When using the GTS with the vehicle engine switch off, connect the GTS to the vehicle and turn a courtesy light switch on and off at intervals of 1.5 seconds or less until communication between the GTS and the vehicle begins. Then select the Model Code "KEY REGIST" under manual mode and enter the following menus: Body Electrical / Entry&Start(CAN). While using the GTS, periodically turn a courtesy light switch on and off at intervals of 1.5 seconds or less to maintain communication between the GTS and the vehicle.

  • Before replacing the certification ECU (smart key ECU assembly) or main body ECU (multiplex network body ECU), refer to the Service Bulletin.

  • The immobiliser system uses the CAN communication system. Inspect the communication function by following How to Proceed with Troubleshooting Click here. Troubleshoot the immobiliser system after confirming that the communication systems are functioning properly.

PROCEDURE


  1. PERFORM ACTIVE TEST USING GTS


    1. Connect the GTS to the DLC3.

    2. Turn the engine switch on (IG).

    3. Turn the GTS on.

    4. Enter the following menus: Body Electrical / Entry&Start / Active Test.

    5. Perform the Active Test according to the display on the GTS.

      Entry&Start
      Tester Display Test Part Control Range Diagnostic Note
      Immobiliser Indicator Security indicator light OFF/ON -
      OK
      The security indicator light operates normally.

    NG

    CHECK HARNESS AND CONNECTOR (SECURITY INDICATOR LIGHT - CERTIFICATION ECU) Click here

    OK

  2. CHECK SECURITY INDICATOR LIGHT OPERATION


    1. When the immobiliser is set, check that the security indicator light blinks.*1

      OK
      The security indicator light blinks normally.

    2. When the theft deterrent system is in the arming preparation state, check that the security indicator light on Click here.*2

      OK
      The security indicator light is on normally.
      Result
      Result Proceed to
      *1 is NG (*2 is OK) A
      *2 is NG (*1 is OK) B

    B

    REPLACE MAIN BODY ECU (MULTIPLEX NETWORK BODY ECU) Click here

    A

    REPLACE CERTIFICATION ECU (SMART KEY ECU ASSEMBLY)

  3. CHECK HARNESS AND CONNECTOR (SECURITY INDICATOR LIGHT - CERTIFICATION ECU)


    1. Disconnect the H56 certification ECU (smart key ECU assembly) connector.

    2. Disconnect the H97 security indicator light (multi-media module receiver assembly) connector*1.

    3. Disconnect the H42 security indicator light (radio receiver assembly) connector*2.

    4. Measure the resistance according to the value(s) in the table below.

      Standard Resistance
      Tester Connection Condition Specified Condition
      H97-37 (SEUC) - H56-18 (IND)*1 Always Below 1 Ω
      H97-37 (SEUC) - Body ground*1 Always 10 kΩ or higher
      H42-7 (LP) - H56-18 (IND)*2 Always Below 1 Ω
      H42-7 (LP) - Body ground*2 Always 10 kΩ or higher

      • *1: w/ Navigation System

      • *2: w/o Navigation System


    NG

    REPAIR OR REPLACE HARNESS OR CONNECTOR

    OK

  4. CHECK HARNESS OR CONNECTOR (SECURITY INDICATOR LIGHT - BODY GROUND)


    1. Measure the resistance according to the value(s) in the table below.

      Standard Resistance
      Tester Connection Condition Specified Condition
      H97-12 (GND1) - Body ground*1 Always Below 1 Ω
      H42-9 (GND) - Body ground*2 Always Below 1 Ω

      • *1: w/ Navigation System

      • *2: w/o Navigation System

      Result
      Result Proceed to
      OK (w/ Navigation System) A
      OK (w/o Navigation System) B
      NG C

    B

    REPLACE SECURITY INDICATOR LIGHT (RADIO RECEIVER ASSEMBLY) Click here

    C

    REPAIR OR REPLACE HARNESS OR CONNECTOR

    A

    REPLACE SECURITY INDICATOR LIGHT (MULTI-MEDIA MODULE RECEIVER ASSEMBLY) Click here