DOOR CONTROL RECEIVER (for Quarter) REMOVAL


  1. REMOVE REAR SEAT ASSEMBLY

    Click here

  2. REMOVE REAR DOOR SCUFF PLATE LH


    1. A01G5TH

      Disengage the 8 claws and remove the rear door scuff plate LH.

  3. REMOVE REAR DOOR SCUFF PLATE RH

    Tech Tips

    Use the same procedure as for the LH side.

  4. REMOVE REAR SEAT SIDE GARNISH LH


    1. A01G7BY

      Disengage the 5 claws and remove the rear seat side garnish LH.

  5. REMOVE REAR SEAT SIDE GARNISH RH

    Tech Tips

    Use the same procedure as for the LH side.

  6. REMOVE CHILD RESTRAINT SEAT ANCHOR BRACKET SUB-ASSEMBLY LH


    1. A01G514

      Remove the 2 nuts and child restraint seat anchor bracket sub-assembly LH.

  7. DISCONNECT REAR SEAT INNER WITH CENTER BELT ASSEMBLY LH


    1. A01G6DE

      Remove the bolt and disconnect the floor anchor of the rear seat inner with center belt assembly LH.

  8. DISCONNECT REAR SEAT 3 POINT TYPE OUTER BELT ASSEMBLY LH


    1. A01G616

      Remove the bolt and disconnect the floor anchor of the rear seat 3 point type outer belt assembly LH.

  9. DISCONNECT REAR SEAT 3 POINT TYPE OUTER BELT ASSEMBLY RH

    Tech Tips

    Use the same procedure as for the LH side.

  10. REMOVE ROOF SIDE INNER GARNISH ASSEMBLY LH


    1. A01G4SZ

      Disengage the 4 clips.

    2. Disengage the 2 guides and remove the roof side inner garnish assembly LH.

  11. REMOVE ROOF SIDE INNER GARNISH ASSEMBLY RH

    Tech Tips

    Use the same procedure as for the LH side.

  12. REMOVE CENTER STOP LIGHT SET (w/o Rear Sunshade)


    1. A01G8B6E01

      Slide the center stop light set in the order and directions shown by the arrows in the illustration while pushing it towards the rear of the vehicle to disengage the 4 claws.

    2. A01G49C

      Turn the center stop light set 180° as shown by the arrow in the illustration.

      Tech Tips

      This makes it easier to disconnect the connector.

    3. Disconnect the connector and remove the center stop light set.

  13. REMOVE REAR SEAT SHOULDER BELT HOLE COVER


    1. A01G8HY

      Using a moulding remover, disengage the 2 claws and 2 guides and remove the rear seat shoulder belt cover.

      Tech Tips

      Use the same procedure for the other 2 rear seat shoulder belt hole covers.

  14. REMOVE CHILD RESTRAINT SEAT TETHER ANCHOR COVER


    1. A01G7FH

      Disengage the 2 claws and 2 guides and remove the child restraint seat tether anchor cover.

      Tech Tips

      Use the same procedure for the other child restraint seat tether anchor cover.

  15. REMOVE PACKAGE TRAY TRIM PANEL ASSEMBLY (w/o Rear Sunshade)


    1. A01G97B

      Disengage the 3 clips.

    2. Disengage the 5 guides.

    3. Pass the 3 rear seat belt floor anchors through the package tray trim panel assembly then remove the package tray trim panel assembly.

  16. REMOVE PACKAGE TRAY TRIM PANEL ASSEMBLY (w/ Rear Sunshade)


    1. A01G56E

      Disengage the 3 clips.

    2. Disengage the guide.

    3. Pass the 3 rear seat belt floor anchors through the package tray trim panel assembly then remove the package tray trim panel assembly.

  17. REMOVE DOOR CONTROL RECEIVER (except Separate Type Tire Pressure Warning System)


    1. A01G7WD

      Remove the bolt.

    2. Disengage the guide from the hole to remove the door control receiver.

    3. Disconnect the connector from the door control receiver.

  18. REMOVE DOOR CONTROL AND TIRE PRESSURE MONITORING SYSTEM RECEIVER ASSEMBLY (for Separate Type Tire Pressure Warning System)


    1. A01G9HI

      Remove the 2 bolts.

    2. Disengage the 2 guides from the holes to remove the door control and tire pressure monitoring system receiver assembly.

    3. Disconnect the connector from the door control and tire pressure monitoring system receiver assembly.