REAR DOOR LOCK REMOVAL

Tech Tips


  • Use the same procedure for the LH side and RH side.

  • The following procedure is for the LH side.


  1. PRECAUTION

    Note

    After turning the engine switch off, waiting time may be required before disconnecting the cable from the negative (-) battery terminal. Therefore, make sure to read the disconnecting the cable from the negative (- ) battery terminal notices before proceeding with work Click here.

  2. DISCONNECT CABLE FROM NEGATIVE BATTERY TERMINAL

    CAUTION:

    Wait at least 90 seconds after disconnecting the cable from the negative (-) battery terminal to disable the SRS system.

    Note

    When disconnecting the cable, some systems need to be initialized after the cable is reconnected Click here.

  3. REMOVE REAR DOOR INSIDE HANDLE BEZEL PLUG


    1. A01G862

      Using a moulding remover, disengage the 3 claws and remove the rear door inside handle bezel plug as shown in the illustration.

  4. REMOVE REAR POWER WINDOW REGULATOR SWITCH ASSEMBLY WITH REAR DOOR ARMREST BASE PANEL


    1. A01G8H1

      Using a moulding remover, disengage the 2 clips, 4 claws and 2 guides as shown in the illustration.

    2. Disconnect the connector and remove the rear power window regulator switch assembly with rear door armrest base panel.

  5. REMOVE DOOR PULL HANDLE COVER


    1. A01G8OX

      Remove the door pull handle cover.

  6. REMOVE REAR DOOR NO. 1 STIFFENER CUSHION


    1. A01G5KG

      Remove the screw and rear door No. 1 stiffener cushion.

  7. REMOVE COURTESY LIGHT ASSEMBLY


    1. A01G77RE01
      Text in Illustration
      *A for LH Side
      *B for RH Side
      *1 Protective Tape

      Using a screwdriver with its tip wrapped with protective tape, disengage the claw.

    2. Disconnect the connector and remove the courtesy light assembly.

  8. REMOVE REAR DOOR TRIM BOARD SUB-ASSEMBLY


    1. A01G4S2E01
      Text in Illustration
      *1 Protective Tape

      Put protective tape around the rear door panel.

    2. A01G7YL

      Remove the 3 screws.

    3. A01G6Q6

      Using a clip remover, disengage the 8 clips.

    4. A01G5L8E01
      Text in Illustration
      *1 Reference Boss
      *2 Rear Door Inner Glass Weatherstrip

      Pull out the rear door trim board sub-assembly in the direction indicated by the arrow as shown in the illustration.

    5. Disengage the reference boss from the rear door panel.

    6. Using a screwdriver, disengage the 4 claws and disconnect the rear door trim board sub-assembly.

    7. w/ Illumination:


      1. Disconnect the connector.

    8. for 15 Speakers:


      1. Disconnect the connector.

    9. A01G4K7

      Disconnect the rear door lock remote control cable assembly and rear door inside locking cable assembly to remove the rear door trim board sub-assembly.

    10. A01G4O8

      Remove the No. 1 door scuff plate clamp.

  9. REMOVE REAR DOOR INNER GLASS WEATHERSTRIP


    1. A01G6GI

      Remove the rear door inner glass weatherstrip.

  10. REMOVE REAR SIDE CURTAIN ASSEMBLY (w/ Rear Door Sunshade)


    1. A01G6F2

      Disengage the 2 clips and 2 claws and remove the rear side curtain assembly.

  11. REMOVE REAR DOOR ARMREST SET BRACKET


    1. A01G4PX

      Remove the 2 screws and rear door armrest set bracket.

  12. REMOVE REAR DOOR SERVICE HOLE COVER


    1. A01G9QA

      Disconnect the connector.

    2. Disengage the 2 clamps and remove the rear door service hole cover.

      Tech Tips

      Remove any remaining butyl tape from the rear door door.

  13. DISCONNECT REAR DOOR WEATHERSTRIP


    1. A01G749

      Disconnect the upper part of the rear door weatherstrip as shown in the illustration.

  14. REMOVE REAR DOOR FRAME GARNISH


    1. A01G830

      Disengage the 3 claws and remove the rear door frame garnish.

  15. REMOVE REAR DOOR GLASS RUN


    1. A01G808

      Remove the rear door glass run.

  16. REMOVE REAR DOOR NO. 1 VENT SEAL


    1. A01G613

      Remove the rear door No. 1 vent seal.

  17. REMOVE REAR DOOR LOWER WINDOW FRAME SUB-ASSEMBLY


    1. A01G78T

      Remove the 2 bolts and screw, and rear door lower window frame sub-assembly.

      Note

      When the rear door lower window frame sub-assembly is removed, do not allow the rear door quarter window glass to fall.

  18. REMOVE REAR DOOR QUARTER WINDOW GLASS


    1. A01G99D

      Remove the rear door quarter window glass with the rear door quarter window weatherstrip as shown in the illustration.

    2. Remove the rear door quarter window glass from the rear door quarter window weatherstrip.

  19. REMOVE REAR DOOR GLASS ASSEMBLY


    1. A01G7UC

      Remove the rear door glass assembly from the rear door window regulator assembly as shown in the illustration.

      Note

      Do not damage the door glass assembly.

  20. REMOVE REAR DOOR LOCK ASSEMBLY


    1. A01G8UDE01
      Text in Illustration
      *1 Release Plate

      Using a T30 "TORX" socket wrench, remove the 3 screws.

    2. Move the rear door lock assembly downward and pull the release plate out of the rear door outside handle frame.

    3. When reusing the rear door lock assembly:


      1. A01G89I

        Remove the door lock wiring harness seal from the rear door lock assembly.

  21. REMOVE REAR DOOR LOCK REMOTE CONTROL CABLE ASSEMBLY


    1. A01G74I

      Using a screwdriver, disengage the claw as shown in the illustration.

    2. A01G8GU

      Remove the rear door lock remote control cable assembly as shown in the illustration.

  22. REMOVE REAR DOOR INSIDE LOCKING CABLE ASSEMBLY


    1. A01G5F0

      Using a screwdriver, disengage the 3 claws as shown in the illustration.

    2. A01G80D

      Remove the rear door inside locking cable assembly as shown in the illustration.