CLEARANCE WARNING BUZZER REMOVAL


  1. PRECAUTION (for Multi-Media Module Receiver Type)

    Note

    After turning the engine switch off, waiting time may be required before disconnecting the cable from the negative (-) battery terminal. Therefore, make sure to read the disconnecting the cable from the negative (-) battery terminal notices before proceeding with work Click here.

  2. CUSTOMIZE POWER TILT AND POWER TELESCOPIC STEERING COLUMN SYSTEM (for Power Tilt and Power Telescopic Steering Column)


    1. Disable the auto away/return function by changing the customize parameter Click here.

      Note

      Record the current customize parameter setting (whether the auto away/return function is enabled or disabled) in order to restore the current setting after finishing this operation.

      Tech Tips

      Performing the above operation disables the auto away/return function when the engine switch is turned off.

    2. Turn the engine switch on (IG). Operate the tilt and telescopic switch to fully extend and lower the steering column assembly.

    3. Turn the engine switch off.

  3. DISCONNECT CABLE FROM NEGATIVE BATTERY TERMINAL (for Multi-Media Module Receiver Type)

    Note

    When disconnecting the cable, some systems need to be initialized after the cable is reconnected Click here.

  4. REMOVE INSTRUMENT CLUSTER FINISH PANEL SUB-ASSEMBLY


    1. A01G9R9

      Using a moulding remover, disengage the 4 clips and 2 guides.

    2. A01G5IT

      Remove the 2 screws.

    3. A01G8GI

      Disengage the 5 claws and 2 guides and remove the instrument cluster finish panel sub-assembly.

  5. REMOVE CENTER INSTRUMENT CLUSTER FINISH PANEL GARNISH


    1. A01G8LME02
      Text in Illustration
      *a Protective Tape

      Apply protective tape to the area shown in the illustration.

    2. Using a moulding remover, disengage the 10 claws and 2 clips as shown in the illustration.

      A01G942

    3. Disconnect the connector to remove the center instrument cluster finish panel garnish.

  6. REMOVE NO. 2 INSTRUMENT PANEL REGISTER ASSEMBLY


    1. Using a moulding remover, disengage the 11 claws and clip as shown in the illustration.

      A01G4E6

    2. Disconnect the connector to remove the No. 2 instrument panel register assembly.

  7. REMOVE LOWER CENTER INSTRUMENT PANEL FINISH PANEL


    1. A01G6Z9E01
      Text in Illustration
      *a Lower Center Instrument Panel Finish Panel Hole

      Insert a moulding remover as shown in the illustration.

    2. A01G5J0

      Using a moulding remover, disengage the 2 claws and 5 clips and remove the lower center instrument panel finish panel as shown in the illustration.

  8. REMOVE RADIO RECEIVER ASSEMBLY WITH BRACKET (for Radio Receiver Type)


    1. A01G5MB

      Remove the 4 bolts.

    2. A01G9PQ

      Pull the radio receiver assembly with bracket toward the rear of the vehicle and disengage the 2 clips and 2 claws.

    3. Disconnect each connector and remove the radio receiver assembly with bracket.

  9. REMOVE MULTI-MEDIA MODULE RECEIVER ASSEMBLY WITH BRACKET (for Multi-Media Module Receiver Type)


    1. A01G7L8

      Remove the 4 bolts.

    2. A01G97K

      Pull the multi-media module receiver assembly with bracket toward the rear of the vehicle and disengage the 2 clips and 2 claws.

    3. Disconnect each connector and remove the multi-media module receiver assembly with bracket.

  10. REMOVE NO. 1 CLEARANCE WARNING BUZZER


    1. for LHD:


      1. A01G7YH

        Disconnect the connector.

      2. Disengage the clamp and remove the No. 1 clearance warning buzzer.

    2. for RHD:


      1. A01G465

        Disconnect the connector.

      2. Disengage the clamp and remove the No. 1 clearance warning buzzer.