CLEARANCE WARNING ECU (for RHD) INSTALLATION


  1. INSTALL CLEARANCE WARNING ECU ASSEMBLY


    1. Engage the 2 claws to install the clearance warning ECU assembly.

  2. INSTALL ECU INTEGRATION BOX RH


    1. Install the ECU integration box RH with the bolt and 2 nuts.

      Torque:
      Nut
      5.5 N*m  { 56 kgf*cm, 49 in.*lbf }
      Bolt
      7.5 N*m  { 76 kgf*cm, 66 in.*lbf }

    2. Connect each connector.

  3. INSTALL LOWER NO. 1 INSTRUMENT PANEL AIRBAG ASSEMBLY


    1. Check that the engine switch is off.

    2. Check that the cable is disconnected from the negative (-) battery terminal.

      CAUTION:

      Wait at least 90 seconds after disconnecting the cable from the negative (-) battery terminal to disable the SRS system.

    3. A01G56GE01
      Text in Illustration
      *1 No. 1 Interior Illumination Light Assembly
      *a Airbag Connector
      *b Airbag Connector Lock
      *c DLC3

      Connect the airbag connector to the lower No. 1 instrument panel airbag assembly.

      Note

      When connecting any airbag connector, take care not to damage the airbag wire harness.

    4. Push in the airbag connector lock to install the airbag connector.

    5. Engage the 2 claws to connect the DLC3.

    6. Engage the 2 claws to connect the No. 1 interior illumination light assembly.

    7. Engage the 2 hooks to temporarily install the lower No. 1 instrument panel airbag assembly.

    8. Install the 4 bolts.

      Torque:
      10 N*m  { 102 kgf*cm, 7 ft.*lbf }

      Note

      Confirm that the lower No. 1 instrument panel airbag assembly is installed securely without any excessive gaps and is not protruding outward.

  4. INSTALL LOWER NO. 1 INSTRUMENT PANEL FINISH PANEL


    1. for LHD:


      1. Connect each connector and engage each clamp.

      2. Engage the 12 claws, 2 clips and guide.

      3. Install the lower No. 1 instrument panel finish panel with the 2 bolts <B>.

    2. for RHD:


      1. Connect each connector and engage each clamp.

      2. Engage the 6 claws, 3 clips and guide.

      3. Install the lower No. 1 instrument panel finish panel with the 2 bolts <B>.

      4. A01G7GC

        Engage the 2 claws to close the cover as shown in the illustration.

  5. CONNECT HOOD LOCK CONTROL LEVER SUB-ASSEMBLY


    1. Engage the claw and 2 guides to connect the hood lock control lever sub-assembly.

  6. INSTALL INSTRUMENT SIDE PANEL RH


    1. A01G5BG

      Engage the 2 guides as shown in the illustration.

    2. A01G9H5

      Engage the 2 claws and 4 clips to install the instrument side panel RH as shown in the illustration.

  7. INSTALL FRONT DOOR OPENING TRIM COVER RH

    Tech Tips

    Use the same procedure as for the LH side Click here.

  8. INSTALL COWL SIDE TRIM BOARD RH

    Tech Tips

    Use the same procedure as for the LH side Click here.

  9. INSTALL FRONT DOOR SCUFF PLATE RH

    Tech Tips

    Use the same procedure as for the LH side Click here.

  10. INSTALL LOWER CENTER INSTRUMENT PANEL FINISH PANEL


    1. A01G96C

      Engage the 2 claws and 5 clips to install the lower center instrument panel finish panel as shown in the illustration.

  11. CONNECT CABLE TO NEGATIVE BATTERY TERMINAL

    Note

    When disconnecting the cable, some systems need to be initialized after the cable is reconnected Click here.

  12. INSPECT SRS WARNING LIGHT

    Click here