PARKING ASSIST MONITOR SYSTEM (w/ Parallel Parking Assist Function), Diagnostic DTC:C1622

DTC Code DTC Name
C1622 Open or Short Circuit in Back Camera Signal

DESCRIPTION

This DTC is stored if the multi-media module receiver assembly judges that the signals or signal lines between the multi-media module receiver assembly and the rear television camera assembly are not normal as a result of its self check.

DTC No. DTC Detection Condition Trouble Area
C1622 Open or short in the rear television camera assembly signal circuit

  • Harness or connector

  • Rear television camera assembly

  • Multi-media module receiver assembly

WIRING DIAGRAM

A01G7P8E02

INSPECTION PROCEDURE

Note


  • When "System initializing" is displayed on the multi-display assembly after disconnecting the cable from the negative (-) battery terminal, correct the steering angle neutral point Click here.

  • Depending on the parts that are replaced or operations that are performed during vehicle inspection or maintenance, calibration of other systems as well as the parking assist monitor system may be needed Click here.

PROCEDURE


  1. CHECK HARNESS AND CONNECTOR (MULTI-MEDIA MODULE RECEIVER ASSEMBLY - REAR TELEVISION CAMERA ASSEMBLY)


    1. Disconnect the H97 multi-media module receiver assembly connector.

    2. Disconnect the U6 rear television camera assembly connector.

    3. Measure the resistance according to the value(s) in the table below.

      Standard Resistance
      Tester Connection Condition Specified Condition
      H97-39 (CA+) - U6-6 (CB+) Always Below 1 Ω
      H97-18 (V+) - U6-3 (CV+) Always Below 1 Ω
      H97-19 (V-) - U6-2 (CV-) Always Below 1 Ω
      H97-40 (CGND) - U6-5 (CGND) Always Below 1 Ω
      H97-39 (CA+) - Body ground Always 10 kΩ or higher
      H97-18 (V+) - Body ground Always 10 kΩ or higher
      H97-19 (V-) - Body ground Always 10 kΩ or higher
      H97-40 (CGND) - Body ground Always 10 kΩ or higher

    NG

    REPAIR OR REPLACE HARNESS OR CONNECTOR

    OK

  2. CHECK MULTI-MEDIA MODULE RECEIVER ASSEMBLY (V-, CGND, CA+)


    1. A01G6VRE18
      Text in Illustration
      *a

      Component with harness connected

      (Multi-media Module Receiver Assembly)

      Reconnect the H97 multi-media module receiver assembly connector.

    2. Measure the resistance according to the value(s) in the table below.

      Standard Resistance
      Tester Connection Condition Specified Condition
      H97-40 (CGND) - Body ground Always Below 1 Ω
      H97-19 (V-) - Body ground Always Below 1 Ω

    3. Measure the voltage according to the value(s) in the table below.

      Standard Voltage
      Tester Connection Condition Specified Condition
      H97-39 (CA+) - H97-40 (CGND)

      Engine switch on (IG)

      Shift lever in R

      		 5.5 to 7.05 V

    NG

    REPLACE MULTI-MEDIA MODULE RECEIVER ASSEMBLY Click here

    OK

  3. CHECK MULTI-MEDIA MODULE RECEIVER ASSEMBLY (V+, GND1)


    1. A01G6VRE21
      Text in Illustration
      *a

      Component with harness connected

      (Multi-media Module Receiver Assembly)

      Reconnect the U6 rear television camera assembly connector.

    2. A01G8XQE35
      Text in Illustration
      *a Waveform 1 (under normal conditions)
      *b Waveform 2 (camera lens is covered, blacking out the screen)
      *c Synchronized Signal
      *d Video Waveform

      Check the waveform of the rear television camera assembly using an oscilloscope.

      Tech Tips

      A waterproof connector is used for the rear television camera assembly. Therefore, inspect the waveform at the multi-media module receiver assembly with the connector connected.

      OK
      Waveform is as shown in the illustration.
      Item Content
      Terminal No. (Symbol) H97-18 (V+) - H97-12 (GND1)
      Tool Setting 200 mV/DIV., 50 μsec./DIV.
      Condition Engine switch on (IG), shift lever in R

      Tech Tips

      The video waveform changes according to the image sent by the rear television camera assembly.


    NG

    REPLACE REAR TELEVISION CAMERA ASSEMBLY Click here

    OK

    REPLACE MULTI-MEDIA MODULE RECEIVER ASSEMBLY Click here