LEXUS PARKING ASSIST-SENSOR SYSTEM Clearance Sonar Main Switch Circuit

DESCRIPTION

The back sonar or clearance sonar switch assembly is installed at the base of the driver side of the instrument panel.

When the clearance sonar main switch is turned on, an on signal is sent to the clearance warning ECU assembly. The LEXUS parking assist-sensor system operates according to this signal.

WIRING DIAGRAM

A01G7LLE24

INSPECTION PROCEDURE

Note

Inspect the fuses for circuits related to this system before performing the following inspection procedure.

PROCEDURE


  1. READ VALUE USING GTS


    1. Connect the GTS to the DLC3.

    2. Turn the engine switch on (IG).

    3. Turn the GTS on.

    4. Enter the following menus: Body Electrical / Clearance Sonar / Data List.

    5. According to the display on the GTS, read the Data List.

      Clearance Sonar
      Tester Display Measurement Item/Range Normal Condition Diagnostic Note
      Main Switch Clearance sonar main switch/OFF or ON

      OFF: Clearance sonar main switch off

      ON: Clearance sonar main switch on

      		 -
      Clearance Sonar ECU Type Type of clearance sonar ECU/Normal Normal: Normal clearance sonar type -
      Result
      Result Proceed to

      Both of the following conditions are met:


      • The display changes as shown above when the clearance sonar main switch is operated.


      • "Normal" is displayed.

      		 A
      "Normal" is not displayed. B

      Both of the following conditions are met:


      • The display does not change as shown above when the clearance sonar main switch is operated.


      • "Normal" is displayed.

      		 C

    B

    REPLACE CLEARANCE WARNING ECU ASSEMBLY Click here

    C

    INSPECT BACK SONAR OR CLEARANCE SONAR SWITCH ASSEMBLY Click here

    A

    PROCEED TO NEXT SUSPECTED AREA SHOWN IN PROBLEM SYMPTOMS TABLE Click here

  2. INSPECT BACK SONAR OR CLEARANCE SONAR SWITCH ASSEMBLY


    1. Remove the back sonar or clearance sonar switch assembly Click here.

    2. A01G5L7E10
      Text in Illustration
      *a

      Component without harness connected

      (Back Sonar or Clearance Sonar Switch Assembly)

      Measure the resistance according to the value(s) in the table below.

      Standard Resistance
      Tester Connection Condition Specified Condition
      9 (IG) - 6 (ECU) Clearance sonar main switch on Below 1 Ω
      9 (IG) - 6 (ECU) Clearance sonar main switch off 10 kΩ or higher

    NG

    REPLACE BACK SONAR OR CLEARANCE SONAR SWITCH ASSEMBLY Click here

    OK

  3. CHECK HARNESS AND CONNECTOR (BACK SONAR OR CLEARANCE SONAR SWITCH ASSEMBLY POWER SOURCE)


    1. Measure the voltage according to the value(s) in the table below.

      Standard Voltage
      Tester Connection Condition Specified Condition
      H3-9 (IG) - Body ground Engine switch on (IG) 11 to 14 V
      H3-9 (IG) - Body ground Engine switch off Below 1 V

    NG

    REPAIR OR REPLACE HARNESS OR CONNECTOR

    OK

  4. CHECK HARNESS AND CONNECTOR (BACK SONAR OR CLEARANCE SONAR SWITCH ASSEMBLY - CLEARANCE WARNING ECU ASSEMBLY)


    1. Disconnect the H61 clearance warning ECU assembly connector.

    2. Measure the resistance according to the value(s) in the table below.

      Standard Resistance
      Tester Connection Condition Specified Condition
      H61-38 (CLSW) - H3-6 (ECU) Always Below 1 Ω
      H61-38 (CLSW) - Body ground Always 10 kΩ or higher

    NG

    REPAIR OR REPLACE HARNESS OR CONNECTOR

    OK

    REPLACE CLEARANCE WARNING ECU ASSEMBLY Click here