NAVIGATION RECEIVER REMOVAL


  1. PRECAUTION

    Note


    • After turning the engine switch off, waiting time may be required before disconnecting the cable from the negative (-) battery terminal. Therefore, make sure to read the disconnecting the cable from the negative (-) battery terminal notices before proceeding with work Click here.

    • A Hard Disk Drive (HDD) is built into the multi-media module receiver assembly to store map and other data, and is used for the navigation system. Therefore, care must be taken for the following points when handling the multi-media module receiver assembly.

    • When removing the hard disk drive, eliminate static electricity by touching the vehicle body to prevent components from being damaged.

  2. CUSTOMIZE POWER TILT AND POWER TELESCOPIC STEERING COLUMN SYSTEM (for Power Tilt and Power Telescopic Steering Column)


    1. Disable the auto away/return function by changing the customize parameter Click here.

      Note

      Record the current customize parameter setting (whether the auto away/return function is enabled or disabled) in order to restore the current setting after finishing this operation.

      Tech Tips

      Performing the above operation disables the auto away/return function when the engine switch is turned off.

    2. Turn the engine switch on (IG). Operate the tilt and telescopic switch to fully extend and lower the steering column assembly.

    3. Turn the engine switch off.

  3. DISCONNECT CABLE FROM NEGATIVE BATTERY TERMINAL

    Note

    When disconnecting the cable, some systems need to be initialized after the cable is reconnected Click here.

  4. REMOVE INSTRUMENT CLUSTER FINISH PANEL SUB-ASSEMBLY


    1. A01G9R9

      Using a moulding remover, disengage the 4 clips and 2 guides.

    2. A01G5IT

      Remove the 2 screws.

    3. A01G8GI

      Disengage the 5 claws and 2 guides and remove the instrument cluster finish panel sub-assembly.

  5. REMOVE CENTER INSTRUMENT CLUSTER FINISH PANEL GARNISH


    1. A01G8LME02
      Text in Illustration
      *a Protective Tape

      Apply protective tape to the area shown in the illustration.

    2. Using a moulding remover, disengage the 10 claws and 2 clips as shown in the illustration.

      A01G942

    3. Disconnect the connector to remove the center instrument cluster finish panel garnish.

  6. REMOVE NO. 2 INSTRUMENT PANEL REGISTER ASSEMBLY


    1. Using a moulding remover, disengage the 11 claws and clip as shown in the illustration.

      A01G4E6

    2. Disconnect the connector to remove the No. 2 instrument panel register assembly.

  7. REMOVE LOWER CENTER INSTRUMENT PANEL FINISH PANEL


    1. A01G6Z9E01
      Text in Illustration
      *a Lower Center Instrument Panel Finish Panel Hole

      Insert a moulding remover as shown in the illustration.

    2. A01G5J0

      Using a moulding remover, disengage the 2 claws and 5 clips and remove the lower center instrument panel finish panel as shown in the illustration.

  8. REMOVE MULTI-MEDIA MODULE RECEIVER ASSEMBLY WITH BRACKET


    1. A01G7L8

      Remove the 4 bolts.

    2. A01G97K

      Pull the multi-media module receiver assembly with bracket toward the rear of the vehicle and disengage the 2 clips and 2 claws.

    3. Disconnect each connector and remove the multi-media module receiver assembly with bracket.

  9. REMOVE NO. 1 RADIO BRACKET


    1. A01G7JS

      Remove the 4 screws and No. 1 radio bracket.

  10. REMOVE NO. 2 RADIO BRACKET


    1. A01G688

      Remove the 4 screws and No. 2 radio bracket.

  11. REMOVE HARD DISK DRIVE


    1. A01G4Z4

      Remove the 2 screws.

    2. Disengage the 2 guides to remove the cover.

    3. A01G860E01
      Text in Illustration
      *1 Protective Tape

      Using a screwdriver with its tip wrapped with protective tape, slide the hard disk drive in the direction shown by the arrow to remove it.

  12. REMOVE MULTI-MEDIA MODULE RECEIVER ASSEMBLY