WINDSHIELD GLASS INSTALLATION

Note

When replacing the windshield glass of a vehicle equipped with a lane departure warning camera, make sure to use a Lexus genuine part. The lane departure warning camera may not be able to be installed due to a missing bracket or the lane departure alert system may not operate properly due to a difference in the transmissivity or black ceramic border.


  1. INSTALL NO. 1 WINDSHIELD GLASS STOPPER (for 2-piece Type)


    1. A01G4ZF

      Install 2 new No. 1 windshield glass stoppers to the vehicle body as shown in the illustration.

      Tech Tips

      Only 2-piece type windshield glass stoppers are provided as supply parts. Use 2-piece type stoppers as replacements even if 1-piece type stoppers were originally installed.

  2. INSTALL NO. 2 WINDSHIELD GLASS STOPPER (for 2-piece Type)


    1. Using a brush or sponge, coat the application area of 2 new No. 2 windshield glass stoppers with primer G.

      Note


      • Do not apply too much primer G.

      • Allow the primer G to dry for 3 minutes or more.

      • Throw away any leftover primer G.

      Tech Tips

      If an area other than specified is coated by accident, wipe off the primer G with a clean piece of cloth before it dries.

    2. A01G6DUE01
      Text in Illustration
      *A Back Side
      *a Windshield Glass Edge Side
      *b Ceramic Notch

      Install the 2 new No. 2 windshield glass stoppers onto the windshield glass as shown in the illustration.

      Standard Dimension
      Area Dimension
      a for Standard 13.6 to 14.6 mm (0.535 to 0.575 in.)
      for Glass Roof 25.7 to 26.7 mm (1.01 to 1.05 in.)

      Tech Tips

      Only 2-piece type windshield glass stoppers are provided as supply parts. Use the 2-piece type stoppers as replacements even if 1-piece type stoppers were originally installed.

  3. INSTALL WINDSHIELD GLASS RETAINER


    1. Using a brush or sponge, coat the application area of 2 new windshield glass retainers with primer G.

      Note


      • Do not apply too much primer G.

      • Allow the primer G to dry for 3 minutes or more.

      • Throw away any leftover primer G.

      Tech Tips

      If an area other than specified is coated by accident, wipe off the primer G with a clean piece of cloth before it dries.

    2. A01G8EOE01
      Text in Illustration
      *A Back Side
      *a Ceramic Notch

      Install the 2 new windshield glass retainers onto the windshield glass as shown in the illustration.

  4. INSTALL WINDSHIELD OUTSIDE MOULDING


    1. Using a brush or sponge, coat the application area of new windshield outside moulding with primer G.

      Note


      • Do not apply too much primer G.

      • Allow the primer G to dry for 3 minutes or more.

      • Throw away any leftover primer G.

      Tech Tips

      If an area other than specified is coated by accident, wipe off the primer G with a clean piece of cloth before it dries.

    2. A01G610E01
      Text in Illustration
      *A Back Side
      *B for Standard
      *C for Glass Roof

      Install the new windshield outside moulding onto the windshield glass as shown in the illustration.

      Standard Dimension
      Area Dimension
      a 6.65 mm (0.262 in.)
      b 10.0 mm (0.394 in.)

      Note


      • Do not apply too much primer G.

      • Allow the primer G to dry for 3 minutes or more.

      • Throw away any leftover primer G.

      Tech Tips

      If an area other than specified is coated by accident, wipe off the primer G with a clean piece of cloth before it dries.

  5. INSTALL WINDSHIELD GLASS ADHESIVE DAM


    1. Using a brush or sponge, coat the application area of a new windshield glass adhesive dam with primer G.

      Note


      • Do not apply too much primer G.

      • Allow the primer G to dry for 3 minutes or more.

      • Throw away any leftover primer G.

      Tech Tips

      If an area other than specified is coated by accident, wipe off the primer G with a clean piece of cloth before it dries.

    2. Install the windshield glass adhesive dam onto the windshield glass as shown in the illustration.

      A01G7X1E01
      Text in Illustration
      *A Back Side - -
      *1 Windshield Glass Adhesive Dam - -
      *a Ceramic Notch Position *b Ceramic Notch
      Standard Dimension
      Area Dimension
      a 9.6 mm (0.378 in.)

  6. INSTALL WINDSHIELD GLASS ADHESIVE DAM (for Glass Roof)


    1. Using a brush or sponge, coat the application area of a new windshield glass adhesive dam with primer G.

      Note


      • Do not apply too much primer G.

      • Allow the primer G to dry for 3 minutes or more.

      • Throw away any leftover primer G.

      Tech Tips

      If an area other than specified is coated by accident, wipe off the primer G with a clean piece of cloth before it dries.

    2. Install the windshield glass adhesive dam onto the windshield glass as shown in the illustration.

      A01G6PFE01
      Text in Illustration
      *A Back Side - -
      *1 Windshield Glass Adhesive Dam - -
      *a Ceramic Notch - -
      Standard Dimension
      Area Dimension
      a 16.4 mm (0.646 in.)
      b 292.1 mm (11.5 in.)
      c 292.1 mm (11.5 in.)
      d 450 mm (1.476 ft.)
      e 450 mm (1.476 ft.)
      f 20.3 mm (0.799 in.)
      g 19.4 mm (0.764 in.)
      h 19.4 mm (0.764 in.)

  7. INSTALL NO. 1 WINDSHIELD OUTSIDE MOULDING CLIP LH


    1. A01G897

      Using an air riveter or a hand riveter with a nose piece, install the 5 windshield No. 1 outside moulding clips with 5 new rivets.

      Tech Tips

      If the mandrel of the rivet does not come off on the first operation of the rivet gun, slide the rivet gun forward on the mandrel and operate it again.

      Note


      • A01G4VSE09

        Do not pry the rivet with the riveter, as this will cause damage to the riveter and mandrel.

        Text in Illustration
        *1 Riveter
        *2 Mandrel
        *a Incorrect
      • A01G8EGE10

        Confirm that the rivets are seated properly against the roof drip side finish moulding clip.

        Text in Illustration
        *1 Riveter
        *a Incorrect

      • Do not tilt the riveter when installing the rivet to the roof drip side finish moulding clip.

      • Do not leave any clearance between the rivet head and roof drip side finish moulding clip.

      • A01G8IGE12

        Do not leave any clearance between the roof drip side finish moulding clip and front pillar. Firmly hold the 2 items together while installing the rivet.

        Text in Illustration
        *1 Riveter
        *a Incorrect

  8. INSTALL NO. 1 WINDSHIELD OUTSIDE MOULDING CLIP RH

    Tech Tips

    Use the same procedure as for the LH side.

  9. INSTALL WINDSHIELD GLASS SUB-ASSEMBLY


    1. A01G8J4E01
      Text in Illustration
      *1 Matchmark

      Position the windshield glass sub-assembly.


      1. Using suction cups, place the windshield glass sub-assembly in the correct position.

      2. Check that the whole contact surface of the windshield glass sub-assembly rim is perfectly even.

      3. Align the matchmarks on the windshield glass sub-assembly and vehicle body.

        Note

        Check that the windshield glass stoppers are attached to the vehicle body correctly.

      4. Remove the windshield glass sub-assembly.

    2. Using a brush, coat the installation surface on the vehicle body with primer M.

      A01G8MHE01
      Text in Illustration
      *a Edge of Curved Surface - -
      A01G6V4 Primer M - -

      Note


      • Do not coat the adhesive with primer M.

      • Do not apply too much primer M.

      • Allow the primer M to dry for 3 minutes or more.

      • Throw away any leftover primer M.

      Tech Tips

      If an area other than specified is coated by accident, wipe off the primer M with a clean piece of cloth before it dries.

    3. Using a brush or sponge, coat the application area of adhesive with primer G.

      A01G9LLE01
      Text in Illustration
      *A Back Side - -
      *B for Standard *C for Glass Roof
      *a Ceramic Notch Position *b Ceramic Notch
      A01G6V4 Primer G - -
      Standard Dimension
      Area Dimension
      a 8.0 mm (0.315 in.) or more
      b 11.0 mm (0.433 in.) or more
      c 11.0 mm (0.433 in.) or more
      d 7.0 mm (0.276 in.) or more
      e 11.0 mm (0.433 in.) or more
      f 11.0 mm (0.433 in.) or more
      g 11.0 mm (0.433 in.) or more

      Note


      • Do not apply too much primer G.

      • Allow the primer G to dry for 3 minutes or more.

      • Throw away any leftover primer G.

      Tech Tips


      • Apply primer G onto the ceramic notches.

      • If an area other than specified is coated by accident, wipe off the primer G with a clean piece of cloth before it dries.

    4. Apply adhesive to the windshield glass sub-assembly.

      Adhesive
      Toyota Genuine Windshield Glass Adhesive or equivalent

      1. A01G931E05
        Text in Illustration
        *1 Nozzle

        Cut off the tip of the cartridge nozzle as shown in the illustration.

        Standard Dimension
        Area Dimension
        a 8.0 mm (0.315 in.) or more
        b 12.0 mm (0.472 in.) or more

        Tech Tips

        After cutting off the tip, use all adhesive within the time described in the table below.

        Usage Time Frame
        Temperature Usage Time Frame
        35°C (95°F) 15 minutes
        20°C (68°F) 1 hour and 40 minutes
        5°C (41°F) 8 hours

      2. Load the sealer gun with the cartridge.

      3. Apply adhesive to the windshield glass sub-assembly as shown in the illustration.

        A01G8CCE01
        Text in Illustration
        *A Back Side - -
        *B for Standard *C for Glass Roof
        *a Ceramic Notch Position *b Ceramic Notch
        A01G6V4 Adhesive - -
        Standard Dimension
        Area Dimension
        a 4.0 mm (0.157 in.)
        b 4.0 mm (0.157 in.)
        c 4.0 mm (0.157 in.)
        d 7.0 mm (0.276 in.) or more
        e 4.0 mm (0.157 in.)
        f 8.0 mm (0.315 in.)
        g 4.0 mm (0.157 in.)

        Tech Tips

        Apply adhesive onto the ceramic notches.

    5. A01G8J4E01
      Text in Illustration
      *1 Matchmark

      Install the windshield glass sub-assembly.


      1. Using suction cups, position the windshield glass sub-assembly so that the matchmarks are aligned, and press it in gently along the rim.

        Note


        • Check that the windshield glass stoppers are attached to the vehicle body correctly.

        • Check the clearance between the vehicle body and windshield glass sub-assembly.

      2. Lightly press the front surface of the windshield glass sub-assembly to ensure that the windshield glass is securely fit to the vehicle body.

        Tech Tips

        Press the glass with a force of 98 N (10 kgf, 22.0 lbf) or more.

      3. Using a scraper, remove any excess or protruding adhesive.

      4. Hold the windshield glass using protective tape until the applied adhesive becomes hard.

        Note

        Do not drive the vehicle for the time described in the table below.

        Minimum Time
        Temperature Minimum Time prior to Driving Vehicle
        35°C (95°F) 1 hour and 30 minutes
        20°C (68°F) 5 hours
        5°C (41°F) 24 hours

    6. w/ Windshield Deicer System:


      1. Connect the connector.

  10. INSPECT FOR LEAK


    1. After the adhesive has hardened, apply water from the outside of the vehicle. Check that no water leaks into the cabin.

    2. If water leaks into the cabin, allow the water to dry and add adhesive.

    3. Remove the protective tape.

  11. INSTALL ROOF HEADLINING ASSEMBLY

    Click here

  12. INSTALL INNER REAR VIEW MIRROR ASSEMBLY

    Click here

  13. INSTALL LANE DEPARTURE WARNING CAMERA (w/ Lane Departure Alert System)

    Click here

  14. INSTALL RAIN SENSOR (w/ Rain Sensor)

    Click here

  15. INSTALL WINDSHIELD OUTSIDE MOULDING LH


    1. A01G9IU

      Engage the guide and 10 claws to install the windshield outside moulding.

  16. INSTALL WINDSHIELD OUTSIDE MOULDING RH

    Tech Tips

    Use the same procedure as for the LH side.

  17. INSTALL COWL TOP VENTILATOR LOUVER SUB-ASSEMBLY


    1. Engage the 8 guides as shown in the illustration.

      A01G61N

    2. Engage the 6 claws and guide to install the cowl top ventilator louver sub-assembly.

      A01G90W

    3. Engage the claw and connect the windshield outside moulding LH.

    4. Engage the claw and connect the windshield outside moulding RH.

  18. INSTALL FRONT WIPER ARM AND BLADE ASSEMBLY LH


    1. When reusing the front wiper arm and blade assembly LH:


      1. A01G93IE08
        Text in Illustration
        *1 Wiper Arm Serration
        *2 Wiper Pivot Serration

        Clean the wiper arm serrations to remove any burrs, dirt, etc.

        Note

        Do not grind down the wiper arm serrations.

    2. When reusing the windshield wiper link assembly:


      1. Clean the wiper pivot serrations with a wire brush.

    3. Operate the wiper and stop the windshield wiper motor assembly at the automatic stop position.

    4. A01G9BAE01
      Text in Illustration
      *1 Ceramic Dot

      Install the front wiper arm and blade assembly LH with the nut to the position shown in the illustration.

      Torque:
      22 N*m  { 224 kgf*cm, 16 ft.*lbf }

      Tech Tips

      Hold the wiper arm by hand while tightening the nut.

  19. INSTALL FRONT WIPER ARM AND BLADE ASSEMBLY RH


    1. When reusing the front wiper arm and blade assembly RH:


      1. A01G93IE09
        Text in Illustration
        *1 Wiper Arm Serration
        *2 Wiper Pivot Serration

        Clean the wiper arm serrations to remove any burrs, dirt, etc.

        Note

        Do not grind down the wiper arm serrations.

    2. When reusing the windshield wiper link assembly:


      1. Clean the wiper pivot serrations with a wire brush.

    3. Operate the wiper and stop the windshield wiper motor assembly at the automatic stop position.

    4. A01G61QE01
      Text in Illustration
      *1 Ceramic Dot

      Install the front wiper arm and blade assembly RH with the nut to the position shown in the illustration.

      Torque:
      22 N*m  { 224 kgf*cm, 16 ft.*lbf }

      Tech Tips

      Hold the wiper arm by hand while tightening the nut.

    5. Turn the engine switch on (IG).

    6. Operate the front wiper while spraying washer fluid onto the windshield glass. Make sure that the front wiper functions properly and the wiper does not come into contact with the vehicle body.

    7. Lift each wiper arm twice after the wipers stop and check the wiper set position.

    8. Turn the engine switch off.