STEERING COLUMN ASSEMBLY INSTALLATION


  1. INSTALL STEERING INTERMEDIATE SHAFT ASSEMBLY


    1. A01G4RTE01
      Text in Illustration
      *a Matchmark

      Install the steering intermediate shaft assembly to the steering column assembly.

      Note

      Align the matchmarks on the steering intermediate shaft assembly and the steering column assembly.

    2. Install a new bolt.

      Torque:
      35 N*m  { 360 kgf*cm, 26 ft.*lbf }

  2. INSTALL STEERING POST ASSEMBLY


    1. Install the steering post assembly with the 4 nuts.

      Torque:
      25 N*m  { 255 kgf*cm, 18 ft.*lbf }

    2. Install the ground wire with the bolt.

      Torque:
      8.4 N*m  { 85 kgf*cm, 74 in.*lbf }

    3. Engage the clamp.

    4. Connect the 2 connectors.

    5. Connect the connectors and engage the wire harness clamps to the steering post assembly.

  3. INSTALL NO. 2 AIR DUCT SUB-ASSEMBLY (for LHD)


    1. Engage the 2 claws and guide to install the No. 2 air duct sub-assembly.

  4. INSTALL NO. 2 AIR DUCT SUB-ASSEMBLY (for RHD)


    1. Engage the 2 claws to install the No. 2 air duct sub-assembly.

    2. Install the bolt.

      Torque:
      9.8 N*m  { 100 kgf*cm, 87 in.*lbf }

  5. CONNECT STEERING INTERMEDIATE SHAFT ASSEMBLY


    1. A01G5H5E01
      Text in Illustration
      *a Matchmark

      Connect the steering intermediate shaft assembly to the steering link assembly.

      Note

      Align the matchmarks on the steering intermediate shaft assembly and the steering link assembly.

    2. Install a new bolt.

      Torque:
      35 N*m  { 360 kgf*cm, 26 ft.*lbf }
    3. A01G71B

      Tighten the clamp.

  6. INSTALL TURN SIGNAL SWITCH ASSEMBLY WITH SPIRAL CABLE SUB-ASSEMBLY

    Note


    • Do not replace the spiral cable with sensor sub-assembly with the battery connected and the engine switch on (IG).

    • Do not rotate the spiral cable with sensor sub-assembly without the steering wheel with the battery connected and the engine switch on (IG).

    • Ensure that the steering wheel is installed and aligned straight when inspecting the steering sensor.


    1. Engage the 3 claws to install the turn signal switch assembly with spiral cable sub-assembly to the steering post assembly.

    2. Connect the connectors to the turn signal switch assembly with spiral cable sub-assembly.

  7. INSTALL UPPER STEERING COLUMN COVER


    1. Engage the 2 claws to install the upper steering column cover.

    2. Engage the 4 clips and 2 guides to the upper steering column cover.

  8. INSTALL LOWER STEERING COLUMN COVER (for Manual Tilt and Manual Telescopic Steering Column)


    1. A01G4YC

      Engage the 2 claws to install the lower steering column cover.

    2. A01G68E

      Install the 2 screws.

      Torque:
      2.0 N*m  { 20 kgf*cm, 18 in.*lbf }
    3. A01G7G8

      Engage the claw.

  9. INSTALL LOWER STEERING COLUMN COVER (for Power Tilt and Power Telescopic Steering Column)


    1. A01G6SZ

      Engage the 2 claws to install the lower steering column cover.

    2. A01G60O

      Install the 3 screws.

      Torque:
      2.0 N*m  { 20 kgf*cm, 18 in.*lbf }

  10. INSTALL LOWER NO. 1 INSTRUMENT PANEL AIRBAG ASSEMBLY

    Click here

  11. TURN FRONT WHEELS TO FACE STRAIGHT AHEAD

  12. INSPECT AND ADJUST SPIRAL CABLE WITH SENSOR SUB-ASSEMBLY

    Note

    Do not adjust the spiral cable with sensor sub-assembly with the battery connected and the engine switch on (IG).


    1. Check that the engine switch is off.

    2. Check that the cable is disconnected from the negative (-) battery terminal.

      CAUTION:

      Wait at least 90 seconds after disconnecting the cable from the negative (-) battery terminal to disable the SRS system.

    3. Check if the spiral cable with sensor sub-assembly is centered.

      A01G6N0E01
      Text in Illustration
      *A w/o Steering Heater *B w/ Steering Heater
      *1 Colored Part *2 Flat Cable
      *a Alignment Mark - -

      Tech Tips

      When the spiral cable with sensor sub-assembly is centered, the alignment marks are aligned and the colored part or flat cable shown in the illustration is visible.

    4. If the spiral cable with sensor sub-assembly is not centered, center it.

      Note


      • When rotating the spiral cable with sensor sub-assembly, make sure to push on the interlock indicated in the illustration to release the interlock mechanism.

      • Do not turn the spiral cable with sensor sub-assembly using the airbag wire harness.


      1. A01G4MIE01
        Text in Illustration
        *1 Interlock

        While pushing on the interlock indicated in the illustration, rotate the spiral cable with sensor sub-assembly counterclockwise slowly by hand until it stops.

      2. A01G6PPE01
        Text in Illustration
        *1 Interlock

        While pushing on the interlock indicated in the illustration, rotate the spiral cable with sensor sub-assembly clockwise approximately 2.5 turns to the position where the colored part or flat cable is visible.

        Tech Tips

        The spiral cable with sensor sub-assembly will rotate approximately 2.5 turns to both the left and right from the center.

  13. INSTALL STEERING WHEEL ASSEMBLY


    1. A01G4KOE01
      Text in Illustration
      *a Matchmark

      Install the steering wheel assembly aligning the matchmarks on the steering wheel assembly and steering main shaft.

    2. Install the steering wheel assembly set nut.

      Torque:
      50 N*m  { 510 kgf*cm, 37 ft.*lbf }

    3. w/ Steering Heater:


      1. A01G5HW

        Connect the connector.

    4. Connect the connectors to the spiral cable sub-assembly.

  14. INSPECT STEERING WHEEL CENTER POINT

  15. INSTALL HORN BUTTON ASSEMBLY

    Click here

  16. INSTALL FRONT WHEEL

    Torque:
    103 N*m  { 1049 kgf*cm, 76 ft.*lbf }

  17. CONNECT CABLE TO NEGATIVE BATTERY TERMINAL (for Power Tilt and Power Telescopic Steering Column)

    Note


    • When disconnecting the cable, some systems need to be initialized after the cable is reconnected Click here.

    • Connect the cable to the negative (-) battery terminal with the front wheels facing straight ahead.

    • Reset the auto tilt away function setting to the previous condition by changing the customize parameter Click here.

  18. TORQUE SENSOR ZERO POINT CALIBRATION

    Click here

  19. ADJUST PARKING ASSIST MONITOR SYSTEM (w/ Parking Assist Monitor System)

    w/ Parallel Parking Assist Function: Click here

    w/o Parallel Parking Assist Function: Click here