VEHICLE STABILITY CONTROL SYSTEM, Diagnostic DTC:C1430, C1431

DTC Code DTC Name
C1430 Brake Pedal Load Sensing Switch OFF Stuck Malfunction
C1431 Brake Pedal Load Sensing Switch ON Stuck Malfunction

DESCRIPTION

Refer to DTC C1429 Click here.

DTC No. DTC Detection Condition Trouble Area
C1430

Either of the following is detected:


  1. With the stop light switch on, the brake pedal load sensing switch off, and the master cylinder pressure 6 MPa (61.2 kgf/cm2, 870 psi) or more, the deceleration is 0.4 G or more for 1 second or more.

  2. With the stop light switch on, the brake pedal load sensing switch off, and the master cylinder pressure 6 MPa (61.2 kgf/cm2, 870 psi) or more, the vehicle speed is 0 km/h (0 mph) for 5 seconds or more.

  • Brake pedal load sensing switch (Brake pedal support assembly)

  • Brake pedal load sensing switch circuit
C1431

Either of the following is detected:


  1. Immediately after the engine switch is turned on (IG), the brake pedal load sensing switch is on and the stop light switch is off for 10 seconds or more.

  2. The condition that the brake pedal load sensing switch remains on while the vehicle speed increases from 0 km/h (0 mph) to 30 km/h (19 mph) occurs 5 times in succession.

  • Brake pedal load sensing switch (Brake pedal support assembly)

  • Brake pedal load sensing switch circuit

WIRING DIAGRAM

Refer to DTC C1429 Click here.

INSPECTION PROCEDURE

Note

When replacing the skid control ECU (brake actuator assembly), perform zero point calibration Click here.

Tech Tips

When C1425 and/or C1426 is output together with C1430 and/or C1431, inspect and repair the trouble areas indicated by C1425 and/or C1426 first Click here and/or Click here.

PROCEDURE


  1. READ VALUE USING GTS (STOP LIGHT SWITCH ASSEMBLY AND BRAKE PEDAL LOAD SENSING SWITCH)


    1. Connect the GTS to the DLC3.

    2. Turn the engine switch on (IG).

    3. Select the Data List using the GTS Click here.

      ABS/VSC/TRC
      Tester Display Measurement Item/Range Normal Condition Diagnostic Note
      Stop Light SW Stop light switch assembly / ON or OFF

      ON: Brake pedal depressed

      OFF: Brake pedal released

      		 -
      Brake Pedal Load Sensing SW Brake pedal load sensing switch / ON or OFF

      ON: Brake pedal depressed beyond a specified point

      OFF: Brake pedal not depressed beyond a specified point

      		 -

    4. Check that the stop light switch display and brake pedal load sensing switch display observed on the GTS change according to brake pedal operation.

      OK
      The GTS displays ON or OFF according to brake pedal operation.

    5. Slowly depress the brake pedal, and check when the stop light switch and brake pedal load sensing switch turn on.

      OK
      First the stop light switch should turn on, and then the brake pedal load sensing switch should turn on.
      Result
      Result Proceed to
      OK A
      NG (Turning on of the brake pedal load sensing switch is not confirmed.) B
      NG (The brake pedal load sensing switch turns on first.) C

    B

    INSPECT BRAKE PEDAL SUPPORT ASSEMBLY Click here

    C

    CHECK BRAKE PEDAL HEIGHT AND STOP LIGHT SWITCH ASSEMBLY INSTALLATION Click here

    A

  2. RECONFIRM DTC


    1. Turn the engine switch off.

    2. Clear the DTCs Click here.

    3. Turn the engine switch off.

    4. Start the engine.

    5. Perform a road test.

    6. Check if the same DTC is output Click here.

      Result
      Result Proceed to
      DTCs C1430 and C1431 are not output. A
      DTCs C1430 and/or C1431 are output. B

    B

    REPLACE BRAKE ACTUATOR ASSEMBLY Click here

    A

    USE SIMULATION METHOD TO CHECK Click here

  3. INSPECT BRAKE PEDAL SUPPORT ASSEMBLY


    1. A01G5EWE01
      Text in Illustration
      *a

      Component without harness connected

      (Brake Pedal Load Sensing Switch (Brake Pedal Support Assembly))

      Turn the engine switch off.

    2. Make sure that there is no looseness at the locking part and the connecting part of the connector.

    3. Disconnect the A32 brake pedal load sensing switch (brake pedal support assembly) connector.

      Note


      • Do not remove the brake pedal load sensing switch from the brake pedal support assembly.

      • When there is a malfunction in the brake pedal load sensing switch, replace the brake pedal support assembly.

    4. Measure the resistance according to the value(s) in the table below.

      Standard Resistance
      Tester Connection Condition Specified Condition
      2 (FSW+) - 1 (FSW-)

      Switch OFF

      (Brake pedal depressed)

      		 950 to 1050 Ω
      2 (FSW+) - 1 (FSW-)

      Switch ON

      (Brake pedal released)

      		 203 to 223 Ω

    NG

    REPLACE BRAKE PEDAL SUPPORT ASSEMBLY Click here

    OK

  4. CHECK HARNESS AND CONNECTOR (BRAKE ACTUATOR ASSEMBLY - BRAKE PEDAL SUPPORT ASSEMBLY)


    1. Make sure that there is no looseness at the locking part and the connecting part of the connector.

    2. Disconnect the A40 skid control ECU (brake actuator assembly) connector.

    3. Measure the resistance according to the value(s) in the table below.

      Standard Resistance
      Tester Connection Condition Specified Condition
      A40-27 (FSW+) - A32-2 (FSW+) Always Below 1 Ω
      A40-27 (FSW+) - Body ground Always 10 kΩ or higher
      A32-1 (FSW-) - Body ground Always Below 1 Ω

    NG

    REPAIR OR REPLACE HARNESS OR CONNECTOR

    OK

    REPLACE BRAKE ACTUATOR ASSEMBLY Click here

  5. CHECK BRAKE PEDAL HEIGHT AND STOP LIGHT SWITCH ASSEMBLY INSTALLATION


    1. Turn the engine switch off.

    2. Check the brake pedal height and stop light switch assembly installation Click here.

      OK
      The brake pedal height and stop light switch assembly installation are normal.

    NG

    ADJUST BRAKE PEDAL HEIGHT OR STOP LIGHT SWITCH ASSEMBLY INSTALLATION Click here

    OK

    REPLACE BRAKE PEDAL SUPPORT ASSEMBLY Click here