VEHICLE STABILITY CONTROL SYSTEM, Diagnostic DTC:C1210, C1336

DTC Code DTC Name
C1210 Zero Point Calibration of Yaw Rate Sensor Undone
C1336 Zero Point Calibration of Acceleration Sensor Undone

DESCRIPTION

The skid control ECU (brake actuator assembly) receives signals from the yaw rate and acceleration sensor (airbag sensor assembly) via the CAN communication system.

The airbag sensor assembly has a built-in yaw rate and acceleration sensor and detects the vehicle's condition.

Tech Tips

If there is a malfunction in the bus lines between the yaw rate and acceleration sensor (airbag sensor assembly) and the CAN communication system, DTC U0124 (Lost Communication with Lateral Acceleration Sensor Module) is output. When U0124 is output together with C1210 and/or C1336, inspect and repair the trouble areas indicated by U0124 first.

These DTCs are also output when the calibration has not been completed.

DTC No. DTC Detection Condition Trouble Area
C1210 Zero point calibration of yaw rate sensor undone. Yaw rate and acceleration sensor (Airbag sensor assembly)
C1336 Zero point calibration of acceleration sensor undone. Yaw rate and acceleration sensor (Airbag sensor assembly)

INSPECTION PROCEDURE

Note

When replacing the skid control ECU (brake actuator assembly) or yaw rate and acceleration sensor (airbag sensor assembly), perform zero point calibration Click here.

Tech Tips

When U0124 and/or U0126 is output together with C1210 and/or C1336, inspect and repair the trouble areas indicated by U0124 and/or U0126 first Click here.

PROCEDURE


  1. PERFORM ZERO POINT CALIBRATION OF YAW RATE AND ACCELERATION SENSOR


    1. Perform zero point calibration of the yaw rate and acceleration sensor Click here.


    NEXT

  2. PERFORM TEST MODE INSPECTION (SIGNAL CHECK)


    1. Turn the engine switch off.

    2. Perform the sensor check in Test Mode Procedure Click here.

      OK
      All Test Mode DTCs are erased.

    NG

    CHECK AIRBAG SENSOR ASSEMBLY INSTALLATION Click here

    OK

    END

  3. CHECK AIRBAG SENSOR ASSEMBLY INSTALLATION


    1. Turn the engine switch off.

    2. Check that the yaw rate and acceleration sensor (airbag sensor assembly) has been installed properly Click here.

      OK
      The sensor should be tightened to the specified torque.
      The sensor should not be installed in a tilted position.

    NG

    INSTALL AIRBAG SENSOR ASSEMBLY CORRECTLY Click here

    OK

  4. READ VALUE USING GTS (YAW RATE AND ACCELERATION SENSOR)


    1. Connect the GTS to the DLC3.

    2. Turn the engine switch on (IG).

    3. Select the Data List using the GTS Click here.

      ABS/VSC/TRC
      Tester Display Measurement Item/Range Normal Condition Diagnostic Note
      Deceleration Sensor

      Acceleration sensor / Min.: -18.525 m/s2, Max.: 18.387 m/s2

      		- During deceleration/acceleration: Changes continuously
      Deceleration Sensor2

      Acceleration sensor 2 / Min.: -18.525 m/s2, Max.: 18.387 m/s2

      		- During deceleration/acceleration: Changes continuously
      Yaw Rate Sensor Yaw rate sensor / Min.: -128 degrees/s, Max.: 127 degrees/s

      Vehicle stopped: 0 degrees/s

      Turning right: -128 to 0 degrees/s

      Turning left: 0 to 127 degrees/s

      		 -

    4. Check that the yaw rate and acceleration sensor (airbag sensor assembly) output value displayed on the GTS.

      OK
      The yaw rate and acceleration sensor (airbag sensor assembly) output value is normal.

      Note

      Check the yaw rate and acceleration sensor signal after replacement Click here.

      Tech Tips

      If troubleshooting has been carried out according to Problem Symptoms Table, refer back to the table and proceed to the next step before replacing parts Click here.


    NG

    REPLACE AIRBAG SENSOR ASSEMBLY Click here

    OK

    REPLACE BRAKE ACTUATOR ASSEMBLY Click here