TRANSMISSION CONTROL CABLE INSTALLATION


  1. INSTALL TRANSMISSION CONTROL CABLE ASSEMBLY

    Note

    Before installing the transmission control cable assembly, check that the park/neutral position switch assembly and the shift lever are in neutral.


    1. Pass the transmission control cable assembly from the cabin to the engine compartment.

    2. Install the transmission control cable assembly to the body with the 2 bolts.

      Torque:
      5.0 N*m  { 51 kgf*cm, 44 in.*lbf }

    3. Install the dash panel insulator to the original position.

    4. Connect the transmission control cable assembly to the No. 1 transmission control cable bracket with a new clip.

    5. Connect the transmission control cable assembly to the transmission control shaft lever with the nut.

      Torque:
      13 N*m  { 130 kgf*cm, 9 ft.*lbf }

      Note

      Before connecting the transmission control cable assembly, check that the park/neutral position switch assembly and the shift lever are in neutral.

    6. Connect the wire harness clamp to the wire harness clamp bracket.

    7. Engage the 2 claws to connect the transmission control cable assembly to the lower shift lever assembly.

    8. A01G54UE03
      Text in Illustration
      *1 Slider
      *2 Lock Piece
      *a Slide
      *b Pull

      Slide the slider of the transmission control cable assembly in the direction indicated by the arrow and pull the lock piece outward.

    9. A01G85ZE01
      Text in Illustration
      *1 Lock Piece

      Install the end of transmission control cable assembly to the lower shift lever assembly.

      Note


      • Check that the lock piece is pulled up.

      • Install the cable end all the way to the base of the pin.

    10. Push the lock piece into the adjuster case.

      Note


      • Check that the park/neutral position switch assembly and the shift lever are in neutral.

      • Securely push in the lock piece until the slider lock is engaged.

  2. CONNECT NO. 1 PARKING BRAKE CABLE ASSEMBLY


    1. Install the No. 1 parking brake cable assembly to the body with the bolt and nut.

      Torque:
      Bolt
      15 N*m  { 153 kgf*cm, 11 ft.*lbf }
      Nut
      5.4 N*m  { 55 kgf*cm, 48 in.*lbf }

  3. INSTALL ACCELERATOR PEDAL SENSOR ASSEMBLY

    Note


    • Avoid physical shock to the accelerator pedal sensor assembly.

    • Do not disassemble the accelerator pedal sensor assembly.

    • This accelerator pedal does not require lubrication. Do not apply oil or other lubrication to the accelerator pedal sensor assembly. If applied, the accelerator pedal sensor assembly must be replaced.


    1. Temporarily install the accelerator pedal sensor assembly with the 2 bolts.

    2. A01G7ETE02

      Tighten the 2 bolts in the order shown in the illustration.

      Torque:
      5.4 N*m  { 55 kgf*cm, 48 in.*lbf }

    3. Connect the accelerator pedal sensor assembly connector.

  4. INSTALL AIRBAG SENSOR ASSEMBLY

    Click here

  5. INSTALL AIR CLEANER CASE SUB-ASSEMBLY


    1. A01G579E01
      Text in Illustration
      *a Hole
      *b Projection

      Insert the projection of the air cleaner case sub-assembly into the hole of the No. 2 air cleaner bracket as shown in the illustration.

    2. Install the 2 bolts.

      Torque:
      5.0 N*m  { 51 kgf*cm, 44 in.*lbf }

    3. Connect the wire harness clamp.

  6. INSTALL AIR CLEANER FILTER ELEMENT SUB-ASSEMBLY

  7. INSTALL AIR CLEANER CAP SUB-ASSEMBLY


    1. A01G6AKE01
      Text in Illustration
      *a Hinge
      *b Clamp

      Connect the 2 hinges of the air cleaner cap sub-assembly.

    2. Install the air cleaner cap sub-assembly with the 2 clamps.

    3. Connect the air cleaner cap sub-assembly to the throttle with motor body assembly the hose clamp.

    4. Connect the ventilation hose to the cylinder head cover.

    5. Install the fuel vapor feed hose to the air cleaner hose.

    6. Connect the mass air flow meter connector and 2 wire harness clamps to the air cleaner cap sub-assembly.

    7. Connect the vacuum switching valve assembly to the air cleaner cap sub-assembly.

  8. INSTALL INLET AIR CLEANER ASSEMBLY


    1. Install the inlet air cleaner assembly with the 2 bolts.

      Torque:
      8.0 N*m  { 82 kgf*cm, 71 in.*lbf }

  9. INSTALL NO. 1 ENGINE COVER SUB-ASSEMBLY


    1. Engage the 3 pins to install the No.1 engine cover sub-assembly.

  10. INSTALL COOL AIR INTAKE DUCT SEAL


    1. Install the cool air intake duct seal with the 9 clips.

  11. INSPECT SHIFT LEVER POSITION


    1. When the shift lever is moved from P to R with the engine switch on (IG) and brake pedal depressed, make sure that the shift lever moves smoothly and correctly into position.

    2. Start the engine and make sure that the vehicle moves forward when the shift lever is moved from N to D and moves rearward when the shift lever is moved to R.