AUTOMATIC TRANSAXLE SYSTEM DATA LIST / ACTIVE TEST


  1. DATA LIST

    Note

    In the table below, the values listed under "Normal Condition" are reference values. Do not depend solely on these reference values when deciding whether a part is faulty or not.

    Tech Tips

    Using the GTS to read the Data List allows the values or states of switches, sensors, actuators and other items to be read without removing any parts. This non-intrusive inspection can be very useful because intermittent conditions or signals may be discovered before parts or wiring is disturbed. Reading the Data List information early in troubleshooting is one way to save diagnostic time.


    1. Warm up the engine.

    2. Turn the A/C switch off.

    3. Turn the engine switch off.

    4. Connect the GTS to the DLC3.

    5. Turn the engine switch on (IG).

    6. Turn the GTS on.

    7. Enter the following menus: Powertrain / Engine and ECT / Data List.

      Tech Tips


      • To display the list box, press the pull down menu button next to Primary. Then select a measurement group.

      • When you select a measurement group, the ECU data belonging to that group is displayed.

      • Measurement Group List / Description


        • All Data / All data

        • Primary / -

        • Engine Control / Engine control system related data

        • Ptrl General / -

        • Ptrl AF Control / Air fuel ratio control system related data

        • Ptrl AF O2 Sensor / Air fuel ratio sensor and heated oxygen sensor related data

        • Ptrl Throttle / Gasoline throttle system related data

        • Ptrl Intake Control / Intake control system related data

        • Ptrl Valve Control / Valve control system related data

        • Ptrl Misfire / "Misfire" related data

        • Ptrl Starting / "Difficult to start" related data

        • Ptrl Rough Idle / "Rough idle" related data

        • Ptrl Evaporative / Evaporative system related data

        • Ptrl CAT Converter / Catalyst converter related data

        • Check Mode / Check mode related data

        • Monitor Status / Monitor status related data

        • Ignition / Ignition system related data

        • Charging Control / Charging control system related data

        • Compression / Data used during "Check the Cylinder Compression" Active Test

        • AT / Automatic transmission system related data

        • Vehicle Information / Vehicle information

    8. According to the display on the GTS, read the Data List.

      Tech Tips


      • The title used for each group of Data List items in this repair manual does not appear on the GTS. However, the name in parentheses after the title, which is a Measurement Group, does appear on the GTS. When the name shown in parentheses is selected on the GTS, all the Data List items listed for that group will be displayed.

      • "Result of real-vehicle check" is the assessment of one vehicle. Use it only for reference.

      Tester Display Measurement Item/Range Normal Condition Diagnostic Note
      Vehicle Speed

      Vehicle speed /

      Min.: 0 km/h (0 mph), Max.: 255 km/h (158 mph)

      		 Actual vehicle speed

      • This is the current vehicle speed.

      • The vehicle speed is detected using the wheel speed sensors.

      • Vehicle speed data is delayed when it is displayed. Therefore, even if the vehicle speed listed in the freeze frame data is 0 km/h (0 mph), this does not always mean that the malfunction occurred when the vehicle was stopped.
      Engine Speed

      Engine speed /

      Min.: 0 rpm, Max.: 16383.75 rpm

      		 610 to 710 rpm: Idling When the crankshaft position sensor is malfunctioning, "Engine Speed" is approximately 0 rpm or varies greatly from the actual engine speed.
      Calculate Load

      Calculated load /

      Min.: 0%, Max.: 100%

      • Engine switch on (IG): 0.0%

      • Idling (engine warmed up): 25.8%

      • Running without load (3000 rpm): 24.3%

      This is the engine load calculated based on the estimated intake manifold pressure.

      Calculate Load = Estimated intake manifold pressure / maximum intake manifold pressure x 100 (%)

      (For example, when the estimated intake manifold pressure is the same as atmospheric pressure, Calculate Load is 100%.)
      Coolant Temp

      Engine coolant temperature /

      Min.: -40°C (-40°F), Max.: 140°C (284°F)

      		 75 to 100°C (167 to 212°F): After warming up

      • If value -40°C (-40°F): sensor circuit open

      • If value 140°C (284°F): sensor circuit shorted
      Engine Run Time

      Engine run time /

      Min.: 0 second,

      Max.: 65535 seconds

      		 Time after engine start

      This is the time elapsed since the engine started.

      Tech Tips

      The time is counted only while the engine is running.
      Battery Voltage

      Battery voltage /

      Min.: 0, Max.: 65.535 V

      		 11 to 14 V: Idling -
      Throttle Sensor Volt %

      Throttle position sensor output/

      Min.: 0%, Max.: 100%

      		 10 to 22%: Idling Calculated value based on VTA1
      Throttle Sensor Position

      Throttle sensor position/

      Min.: 0%, Max.: 100%

      • 0%: Accelerator pedal fully released

      • 50 to 80%: Accelerator pedal fully depressed

      This is the throttle valve opening amount used for engine control.

      (100% signifies 125° of throttle valve rotation. This does not include the amount the throttle valve is opened to maintain the idle speed during idling.)

      This value has no meaning when the engine switch is ON and the engine is stopped.

      The throttle valve opening amount during idling is indicated by 0%. When the throttle valve is fully open, the value is 68%.
      Starter Signal

      Starter signal/

      ON or OFF

      ON: Starter operating

      OFF: Starter not operating

      		 -
      Neutral Position SW Signal

      PNP switch status/

      ON or OFF

      • ON: Shift lever is in P or N

      • OFF: Shift lever is not in P or N

      When the shift lever position displayed on the GTS differs from the actual position, adjustment of the PNP switch or the shift cable may be incorrect.

      Tech Tips

      When the failure still occurs even after adjusting these parts, Click here.
      Stop Light Switch

      Stop light switch status/

      ON or OFF

      Brake pedal is


      • ON: Depressed

      • OFF: Released

      		 -
      TC terminal

      TC terminal Status /

      ON or OFF

      		 - -
      #Codes (Include History)

      # of Codes /

      Min.: 0, Max.: 255

      		 - Number of detected DTCs
      MIL ON Run Distance

      MIL ON run distance /

      Min.: 0 km (0 mile),

      Max.: 65535 km (40723 mile)

      		 Distance after DTC detected This is the distance driven after a DTC is stored.
      Running Time from MIL ON

      Running time from MIL ON /

      Min.: 0 minute,

      Max.: 65535 minutes

      		 Equivalent to running time after MIL ON -
      Time after DTC Cleared

      Time after DTC cleared /

      Min.: 0 minute,

      Max.: 65535 minutes

      		 Equivalent to time after DTCs cleared This is the time elapsed after DTCs were cleared (or after the vehicle left the factory). Time elapsed after the engine switch is turned off is not counted.
      Distance from DTC Cleared

      Distance after DTC cleared /

      Min.: 0 km (0 mile)

      Max.: 65535 km (40723 mile)

      		 Equivalent to time after DTCs cleared This is the distance driven after DTCs were cleared (or after the vehicle left the factory).
      Warmup Cycle Cleared DTC

      Warm-up cycle after DTC cleared /

      Min.: 0, Max.: 255

      		 - Number of warm-up cycles after DTCs cleared
      TC and TE1

      TC and TE1 terminals of DLC3 /

      ON or OFF

      		 - Active Test support data
      Transmission Type Transmission type - -
      SPD (NT)

      Input turbine speed/

      Min.: 0 rpm, Max.: 12750 rpm

      Lock-up is


      • ON (After warming up the engine):

        Input turbine speed (NT) is equal to engine speed

      • OFF (idling with shift lever in N):

        Input turbine speed (NT) is nearly equal to engine speed

      		 Data is displayed in increments of 50 rpm
      SPD (NC)

      Counter gear speed /

      Min.: 0 rpm, Max.: 12750 rpm

      		 - Data is displayed in increments of 50 rpm
      Shift SW Status (P Range)

      PNP switch status/

      ON or OFF

      • ON: Shift lever is in P

      • OFF: Shift lever is not in P

      When the shift lever position displayed on the GTS differs from the actual position, adjustment of the PNP switch or the shift cable may be incorrect.

      Tech Tips

      When the failure still occurs even after adjusting these parts, Click here

      Shift SW Status (R Range)

      PNP switch status/

      ON or OFF

      • ON: Shift lever is in R

      • OFF: Shift lever is not in R

      When the shift lever position displayed on the GTS differs from the actual position, adjustment of the PNP switch or the shift cable may be incorrect.

      Tech Tips

      When the failure still occurs even after adjusting these parts, Click here

      Shift SW Status (N Range)

      PNP switch status/

      ON or OFF

      • ON: Shift lever is in N

      • OFF: Shift lever is not in N

      When the shift lever position displayed on the GTS differs from the actual position, adjustment of the PNP switch or the shift cable may be incorrect.

      Tech Tips

      When the failure still occurs even after adjusting these parts, Click here

      Sports Shift Up SW

      Sport shift up switch status/

      ON or OFF

      • ON: Continuously shift to "+" (up-shift)

      • OFF: Release "+" (up-shift)

      		 -
      Sports Shift Down SW

      Sport shift down switch status/

      ON or OFF

      • ON: Continuously shift to "-" (down-shift)

      • OFF: Release "-" (down-shift)

      		 -
      Sports Mode Selection SW

      Sport mode select switch status/

      ON or OFF

      Shift lever is:


      • ON: S, "+" or "-"

      • OFF: Not in S, "+" or "-"

      		 -
      Shift SW Status (D Range)

      PNP switch status/

      ON or OFF

      • ON: Shift lever is in D or S

      • OFF: Shift lever is not in D or S

      When the shift lever position displayed on the GTS differs from the actual position, adjustment of the PNP switch or the shift cable may be incorrect.

      Tech Tips

      When the failure still occurs even after adjusting these parts, Click here

      A/T Oil Temperature 1

      ATF temp. sensor value/

      min.: -40°C (-40°F)

      max.: 215°C (419°F)

      • After stall test;

        Approx. 80°C (176°F)

      • Equal to ambient temperature when cold soak

      		 If the value is "-40°C (-40°F)" or "150°C (302°F)", ATF temp. sensor circuit is open or shorted.
      NT Sensor Voltage

      Input turbine speed sensor output voltage /

      Min.: 0 V, Max.: 5 V

      		 0.1 to 1.9 V -
      NC Sensor Voltage

      Counter gear speed sensor output voltage /

      Min.: 0 V, Max.: 5 V

      		 0.1 to 1.9 V -
      Lock Up

      Lock up /

      0: OFF / 1: ON

      		 Lock up: ON -
      Shift Status

      ECM gear shift command/

      1st, 2nd, 3rd, 4th, 5th or 6th

      		 Same as actual gear -
      SLT Solenoid Status

      Shift solenoid SLT status/

      ON or OFF

      Shift solenoid SLT is


      • Operating: ON

      • Not operating: OFF

      		 -
      SLU Solenoid Status

      Shift Solenoid SLU Status/

      ON or OFF

      Shift solenoid SLU is


      • Operating: ON

      • Not operating: OFF

      		 -
      SL Solenoid Status

      Shift Solenoid SL Status/

      ON or OFF

      Shift solenoid SL is


      • Operating: ON

      • Not operating: OFF

      		 -
      AT Fluid

      Flex lockup judder judgment flag /

      0: OFF / 1: ON

      		 - -

  2. ACTIVE TEST

    Tech Tips

    Using the GTS to perform Active Tests allows relays, VSVs, actuators and other items to be operated without removing any parts. This non-intrusive functional inspection can be very useful because intermittent operation may be discovered before parts or wiring is disturbed. Performing Active Tests early in troubleshooting is one way to save diagnostic time. Data List information can be displayed while performing Active Tests.


    1. Warm up the engine.

    2. Turn the engine switch off.

    3. Connect the GTS to the DLC3.

    4. Turn the engine switch on (IG).

    5. Turn the GTS on.

    6. Enter the following menus: Powertrain / Engine and ECT / Active Test.

    7. According to the display on the GTS, perform the Active Test.

      Tester Display Test Part Control Range Diagnostic Note
      Connect the TC and TE1

      Connects and disconnects TC and TE1.

      (transitions into the fluid temperature detection mode)

      		 ON/OFF The MIL will not blink when "Connect the TC and TE1 / ON" is selected.
      Activate the Solenoid (SLU) Operates shift solenoid SLU ON/OFF

      [Vehicle Condition]


      • Engine stopped

      • Shift lever in P or N
      Activate the Solenoid (SLT)* Operates shift solenoid SLT to raise the line pressure.

      ON/OFF

      Tech Tips

      ON: No action (normal operation)

      OFF: Line pressure up (When the Active Test of "Activate the Solenoid (SLT)" is performed, the ECM commands the SLT solenoid to turn off).

      [Vehicle Condition]


      • Vehicle Stopped

      • IDL: ON
      Activate the Lock Up Controls the shift solenoid SLU and SL to set the automatic transaxle to the lock-up condition. ON/OFF

      Can be used to check SLU and SL solenoid operation.

      [Vehicle Condition]


      • Throttle valve opening angle: Less than 20%

      • Vehicle speed:60 km/h (37 mph) or more, and 6th gear
      Activate the Solenoid (SL) Operates shift solenoid SL ON/OFF

      [Vehicle Condition]


      • Engine stopped

      • Shift lever in P or N
      Control the Shift Position Operates the shift solenoid valves to allow gears to selected manually.

      • Press "→" button: Upshift occurs

      • Press "←" button: Downshift occurs

      Can be used to check the operation of the shift solenoid valves.

      Upshifts and downshifts should be performed consecutively. A 10-second interval is required between gear changes.

      Do not downshift at high speeds. Doing so will damage the automatic transaxle.

      [Vehicle Condition]


      • 50 km/h (31 mph) or less
      Activate the Solenoid (SL1) Operates shift solenoid SL1 ON/OFF

      [Vehicle Condition]


      • Engine stopped

      • Shift lever in P or N
      Activate the Solenoid (SL2) Operates shift solenoid SL2 ON/OFF

      [Vehicle Condition]


      • Engine stopped

      • Shift lever in P or N
      Activate the Solenoid (SL3) Operates shift solenoid SL3 ON/OFF

      [Vehicle Condition]


      • Engine stopped

      • Shift lever in P or N
      Activate the Solenoid (SL4) Operates shift solenoid SL4 ON/OFF

      [Vehicle Condition]


      • Engine stopped

      • Shift lever in P or N

      *: The "Activate the solenoid (SLT)" Active Test is performed to allow confirmation that the line pressure changes. The line pressure changes are confirmed using the same SST that is used for the Hydraulic Test Click here.

      Tech Tips

      Note that the pressure readings for the Active Test and Hydraulic Test are different.