OIL COOLER REMOVAL


  1. REMOVE FRONT WHEEL OPENING EXTENSION PAD RH (w/ Transmission Oil Thermostat)

  2. REMOVE ENGINE UNDER COVER RH (w/ Transmission Oil Thermostat)

  3. REMOVE FRONT WHEEL OPENING EXTENSION PAD LH (w/ Transmission Oil Thermostat)

  4. REMOVE ENGINE UNDER COVER LH (w/ Transmission Oil Thermostat)

  5. DRAIN AUTOMATIC TRANSAXLE FLUID


    1. Remove the front wheel opening extension pad LH, engine under cover LH and front fender apron seal LH.

    2. A01G5HC

      Remove the refill plug and gasket from the automatic transaxle assembly.

    3. A01G5QL

      Using a 6 mm hexagon socket wrench, remove the overflow plug and gasket from the automatic transaxle assembly.

    4. A01G9CGE04
      Text in Illustration
      *1 No. 1 Transmission Oil Filler Tube
      *2 Hexagon Socket Wrench
      *a Overflow Plug Hole

      Using a 6 mm hexagon socket wrench, remove the No. 1 transmission oil filler tube from the automatic transaxle oil pan sub-assembly.

    5. Drain automatic transaxle fluid from the automatic transaxle assembly.

    6. A01G9CGE04
      Text in Illustration
      *1 No. 1 Transmission Oil Filler Tube
      *2 Hexagon Socket Wrench
      *a Overflow Plug Hole

      Using a 6 mm hexagon socket wrench, install the No. 1 transmission oil filler tube to the automatic transaxle oil pan sub-assembly.

      Torque:
      1.7 N*m  { 17 kgf*cm, 15 in.*lbf }
    7. A01G5QL

      Using a 6 mm hexagon socket wrench, install a new gasket and the overflow plug to the automatic transaxle assembly.

      Torque:
      40 N*m  { 408 kgf*cm, 30 ft.*lbf }
    8. A01G5HC

      Temporarily install the gasket and refill plug to the automatic transaxle assembly.

      Tech Tips

      Reuse the old gasket as the plug will be removed again to adjust the fluid level.

  6. DRAIN ENGINE COOLANT

    CAUTION:

    Do not remove the radiator cap sub-assembly, cylinder block drain cock plugs or radiator drain cock plug while the engine and radiator assembly are still hot. Pressurized, hot engine coolant and steam may be released and cause serious burns.


    1. Loosen the radiator drain cock plug.

    2. Loosen the cylinder block drain cock plug. (for Bank 1)

    3. Loosen the cylinder block drain cock plug. (for Bank 2, w/ Cylinder Block Drain Cock Plug)

    4. Remove the radiator cap sub-assembly.

      A01G49BE04
      Text in Illustration
      *1 Radiator Cap Sub-assembly *2 Cylinder Block Drain Cock Plug (for Bank 1)
      *3 Cylinder Block Drain Cock Plug (for Bank 2, w/ Cylinder Block Drain Cock Plug) *4 Radiator Drain Cock Plug
      *5 Air Drain Cock Plug - -

      Tech Tips

      Collect the engine coolant in a container and dispose of it according to the regulations in your area.

  7. REMOVE COOL AIR INTAKE DUCT SEAL


    1. A01G7XF

      Remove the 9 clips and cool air intake duct seal.

  8. REMOVE INLET NO. 2 AIR CLEANER


    1. A01G8C4

      Disconnect the 2 wire harness clamps and vacuum hose clamp.

    2. Remove the 2 bolts and inlet No. 2 air cleaner.

  9. REMOVE AIR CLEANER CAP SUB-ASSEMBLY


    1. A01G55V

      Disconnect the mass air flow meter connector and wire harness clamp.

    2. A01G6Q3

      Disconnect the 3 hoses.

    3. Disconnect the ventilation hose from the air cleaner cap sub-assembly.

    4. A01G67K

      Loosen the hose clamp and separate the air cleaner cap sub-assembly from the throttle with motor body assembly.

    5. Release the 2 clamps and remove the air cleaner cap sub-assembly.

  10. REMOVE AIR CLEANER FILTER ELEMENT SUB-ASSEMBLY

  11. REMOVE AIR CLEANER CASE SUB-ASSEMBLY


    1. A01G9DG

      Disconnect the 3 wire harness clamps, connector, vacuum hose and No. 1 fuel vapor feed hose.

    2. Remove the 2 bolts and air cleaner case sub-assembly.

  12. REMOVE INLET NO. 1 AIR CLEANER


    1. A01G4LL

      Disengage the pin and remove the inlet No. 1 air cleaner.

  13. REMOVE TRANSMISSION OIL COOLER


    1. w/o Transmission Oil Thermostat:


      1. A01G968E01
        Text in Illustration
        *1 No. 3 Water By-pass Hose
        *2 No. 4 Water By-pass Hose
        *3 No. 1 Oil Cooler Outlet Hose
        *4 No. 1 Oil Cooler Inlet Hose

        Release the 4 clamps and disconnect the No. 3 water by-pass hose, No. 4 water by-pass hose, No. 1 oil cooler outlet hose and No. 1 oil cooler inlet hose from the transmission oil cooler.

    2. w/ Transmission Oil Thermostat:


      1. A01G968E01
        Text in Illustration
        *1 No. 3 Water By-pass Hose
        *2 No. 4 Water By-pass Hose
        *3 No. 1 Transmission Oil Cooler Hose Assembly
        *4 No. 1 Oil Cooler Inlet Hose

        Release the 4 clamps and disconnect the No. 3 water by-pass hose, No. 4 water by-pass hose, No. 1 transmission oil cooler hose assembly and No. 1 oil cooler inlet hose from the transmission oil cooler.

    3. Remove the 3 bolts, transmission oil cooler and transmission oil cooler stay from the front engine mounting bracket.

  14. REMOVE TRANSMISSION OIL THERMOSTAT (w/ Transmission Oil Thermostat)


    1. A01G991E01
      Text in Illustration
      *1 No. 1 Oil Cooler Outlet Hose
      *2 No. 1 Transmission Oil Cooler Hose Assembly
      *3 Transmission Oil Cooler Hose

      Release the 4 clamps and disconnect the 2 transmission oil cooler hoses, No. 1 oil cooler outlet hose and No. 1 transmission oil cooler hose assembly from the transmission oil thermostat.

    2. Remove the bolt and transmission oil thermostat from the front engine mounting insulator.