ROOF HEADLINING REASSEMBLY


  1. INSTALL NO. 1 ROOF WIRE


    1. When using a new roof headlining:


      1. Immediately before installing the No. 1 roof wire, cut off the portion shown in the illustration.

        for LHD:

        A01G50NE02
        Text in Illustration
        *A for Standard *B for Glass Roof
        *C w/o Lane Departure Alert System *D w/ Lane Departure Alert System
        *a Cut Off Size - -
        Cut Off Size
        Area Dimension
        A 10 mm (0.394 in.)

        for RHD:

        A01G9OSE01
        Text in Illustration
        *A for Standard *B for Glass Roof
        *C w/ Rain Sensor - -
        *a Cut Off Size - -
        Cut Off Size
        Area Dimension
        A 10 mm (0.394 in.)

    2. Apply double-sided tape as shown in the illustration.

      A01G86DE02
      Text in Illustration
      *A for Standard *B for Glass Roof
      *a Double-sided Tape Size *b Tape Attachment Locations (Reference)
      *c Marking - -
      A01G6V4 Double-sided Tape - -
      Double-sided Tape Size
      Area Dimension
      A 1 mm (0.0394 in.)
      B 10 mm (0.394 in.)

    3. Peel off the release paper from the double-sided tape.

    4. Attach the No. 1 roof wire along the double-sided tape so that the marking surface of the wire harness faces downward.

    5. Align the edge of the marking tape (A) on the No. 1 roof wire with the markings on the roof headlining.

      A01G4O2E02
      Text in Illustration
      *A for Standard *B for Glass Roof
      *a Marking Tape (A) *b Marking
      *c Marking Tape (B) *d Clamp (A)
      *e Marking Tape (C) *f Adjustment Area
      *g Clamp (B) *h Marking Tape (D)
      *i Marking Tape (E) - -

    6. Align the marking tape (B) on the No. 1 roof wire with the vehicle front end of the roof headlining.

    7. Attach the No. 1 roof wire, starting from the marking tape (B) to the marking tape (A) while aligning it with the double-sided tape.

      Note


      • Securely attach the No. 1 roof wire.

      • If any portion of the No. 1 roof wire is left loose, this will cause abnormal noise. Make sure to attach the No. 1 roof wire without leaving any of it loose.

    8. Turn the visor assembly LH connector clockwise approximately 90° to install it to the roof headlining.

    9. Engage the clamp (A).

    10. Align the edge of the marking tape (C) on the No. 1 roof wire with the markings on the roof headlining.

    11. Attach the No. 1 roof wire, starting from the marking tape (C) to the marking tape (B) while aligning it with the double-sided tape.

      Note


      • Securely attach the No. 1 roof wire.

      • If any portion of the No. 1 roof wire is left loose, this will cause abnormal noise. Make sure to attach the No. 1 roof wire without leaving any of it loose.

      Tech Tips

      Secure the extra length of the No. 1 roof wire in the adjustment area using double-sided tape.

    12. Engage the 3 clamps (B).

    13. Align the edge of the marking tape (D) on the No. 1 roof wire with the markings on the roof headlining.

    14. Align the edge of the marking tape (E) on the No. 1 roof wire with the markings on the roof headlining.

    15. Attach the No. 1 roof wire, starting from the marking tape (D) to the marking tape (E) while aligning it with the double-sided tape.

      Note


      • Securely attach the No. 1 roof wire.

      • If any portion of the No. 1 roof wire is left loose, this will cause abnormal noise. Make sure to attach the No. 1 roof wire without leaving any of it loose.

    16. Turn the visor assembly RH connector clockwise approximately 90° to install it to the roof headlining.

    17. Apply adhesive tape between the markings on the roof headlining as shown in the illustration.

      A01G5LRE01
      Text in Illustration
      *A for Standard *B for Glass Roof
      *1 No. 1 Roof Wire - -
      *a Adhesive Tape Size *b Correct
      *c Incorrect - -
      A01G6V4 Adhesive Tape - -
      Adhesive Tape Size
      Area Dimension
      A 20 mm (0.787 in.)
      B 100 mm (3.94 in.)

  2. INSTALL NO. 2 ANTENNA CORD SUB-ASSEMBLY


    1. Apply double-sided tape as shown in the illustration.

      A01G4ZPE01
      Text in Illustration
      *A for Standard *B for Glass Roof
      *1 Marking - -
      *a Double-sided Tape Size *b Tape Attachment Locations (Reference)
      A01G6V4 Double-sided Tape - -
      A01G47H Front - -
      Double-sided Tape Size
      Area Dimension
      X 1.0 mm (0.0394 in.)
      Y 10.0 mm (0.394 in.)

    2. Peel off the release paper from the double-sided tape.

    3. Align the marking tape on the No. 2 antenna cord sub-assembly with the vehicle front end on the roof headlining assembly. (A)

      A01G67DE02
      Text in Illustration
      *A for Standard *B for Glass Roof
      *1 Adjustment Area - -
      A01G6ZK Marking Tape A01G6V4 Adhesive Tape
      A01G47H Front - -

    4. Engage the 2 guides. (B)

    5. Align the marking tape on the No. 2 antenna cord sub-assembly with the vehicle rear end on the roof headlining assembly. (C)

    6. Align the marking tape on the No. 2 antenna cord sub-assembly with the adjustment area on the roof headlining assembly. (D)

    7. Attach the No. 2 antenna cord sub-assembly with the double-sided tape.

      Note


      • Securely attach the No. 2 antenna cord sub-assembly.

      • If any of the No. 2 antenna cord sub-assembly is left loose, this will cause abnormal noise.

      • Make sure to attach the No. 2 antenna cord sub-assembly without leaving any of it loose.

      Tech Tips

      Secure the extra length of the No. 2 antenna cord sub-assembly in the adjustment area.

    8. Apply adhesive tape by aligning it with the markings on the roof headlining assembly as shown in the illustration.

  3. INSTALL VANITY LIGHT ASSEMBLY


    1. Install the vanity light assembly Click here.

      Tech Tips

      Use the same procedure for the other vanity light.