ROOF HEADLINING REMOVAL


  1. REMOVE FRONT SEAT ASSEMBLY LH

    Click here

  2. REMOVE FRONT SEAT ASSEMBLY RH

    Tech Tips

    Use the same procedure as for the LH side.

  3. REMOVE REAR SEAT ASSEMBLY

    Click here

  4. REMOVE FRONT DOOR SCUFF PLATE LH


    1. A01G8TA

      Disengage the 10 claws and remove the front door scuff plate LH.

  5. REMOVE COWL SIDE TRIM BOARD LH


    1. A01G75T

      Remove the clip.

    2. Disengage the claw and clip, and remove the cowl side trim board LH.

  6. REMOVE FRONT DOOR OPENING TRIM COVER LH


    1. A01G9KP

      Disengage the 3 claws.

    2. Disengage the guide and remove the front door opening trim cover LH.

  7. REMOVE FRONT PILLAR GARNISH LH


    1. A01G55KE01
      Text in Illustration
      *1 Front Pillar Garnish Clip

      Pull the upper part of the garnish toward the inside of the cabin and disengage the garnish from the base of the 2 clips.

      Tech Tips

      Make the front pillar garnish LH hang down from the front pillar garnish clip.

    2. A01G7M3E01

      While pushing the tabs on the front pillar garnish clip in the direction indicated by the arrow (A) shown in the illustration, disengage the front pillar garnish clip.

    3. Pull the garnish in the direction indicated by the arrow (B) shown in the illustration to disengage the 2 guides and remove the front pillar garnish LH.

    4. A01G5BXE01
      Text in Illustration
      *1 Adhesive Tape
      *2 Protective Cover
      *3 Curtain Shield Airbag Assembly

      Protect the curtain shield airbag assembly.


      1. Cover the airbag with a piece of cloth or nylon and secure the edges of the cover with tape as shown in the illustration.

        Note

        Cover the curtain shield airbag with a protective cover as soon as the front pillar garnish LH is removed.

  8. REMOVE REAR DOOR SCUFF PLATE LH


    1. A01G5TH

      Disengage the 8 claws and remove the rear door scuff plate LH.

  9. REMOVE CENTER PILLAR LOWER GARNISH LH


    1. A01G8HO

      Disengage the 2 claws and 2 guides.

    2. Disengage the 5 clips and remove the center pillar lower garnish LH.

  10. REMOVE CENTER PILLAR UPPER GARNISH LH


    1. A01G91V

      Remove the 2 screws.

    2. Disengage the clip.

    3. Pass the floor anchor of the front seat outer belt assembly LH through the center pillar upper garnish LH and remove the center pillar upper garnish LH.

  11. REMOVE FRONT DOOR SCUFF PLATE RH

    Tech Tips

    Use the same procedure as for the LH side.

  12. REMOVE COWL SIDE TRIM BOARD RH

    Tech Tips

    Use the same procedure as for the LH side.

  13. REMOVE FRONT DOOR OPENING TRIM COVER RH

    Tech Tips

    Use the same procedure as for the LH side.

  14. REMOVE FRONT PILLAR GARNISH RH

    Tech Tips

    Use the same procedure as for the LH side.

  15. REMOVE REAR DOOR SCUFF PLATE RH

    Tech Tips

    Use the same procedure as for the LH side.

  16. REMOVE CENTER PILLAR LOWER GARNISH RH

    Tech Tips

    Use the same procedure as for the LH side.

  17. REMOVE CENTER PILLAR UPPER GARNISH RH

    Tech Tips

    Use the same procedure as for the LH side.

  18. REMOVE REAR SEAT SIDE GARNISH LH


    1. A01G7BY

      Disengage the 5 claws and remove the rear seat side garnish LH.

  19. REMOVE ROOF SIDE INNER GARNISH ASSEMBLY LH


    1. A01G4SZ

      Disengage the 4 clips.

    2. Disengage the 2 guides and remove the roof side inner garnish assembly LH.

  20. REMOVE REAR SEAT SIDE GARNISH RH

    Tech Tips

    Use the same procedure as for the LH side.

  21. REMOVE ROOF SIDE INNER GARNISH ASSEMBLY RH

    Tech Tips

    Use the same procedure as for the LH side.

  22. REMOVE LOWER SHIFT LEVER ASSEMBLY

    U660E: Click here

    U760E: Click here

  23. REMOVE INSTRUMENT PANEL SAFETY PAD

    Click here

  24. REMOVE INNER REAR VIEW MIRROR STAY HOLDER COVER


    1. A01G7MS

      Disengage the 2 guides and slide the inner rear view mirror stay holder cover as shown in the illustration.

    2. A01G7QC

      Disengage the 6 claws and remove the inner rear view mirror stay holder cover.

  25. REMOVE RAIN SENSOR COVER (w/o Lane Departure Alert System)

    w/ Rain Sensor: Click here

  26. REMOVE LANE DEPARTURE WARNING CAMERA COVER NO.1 (w/ Lane Departure Alert System)


    1. A01G4S0

      Pull the lane departure warning camera cover in the direction indicated by the arrow to disengage the 4 guides and remove the lane departure warning camera cover as shown in the illustration.

  27. REMOVE ROOF CONSOLE BOX ASSEMBLY


    1. A01G75G

      Using a moulding remover, disengage the 4 clips.

    2. Disengage the 2 guides.

    3. Disconnect the connector and remove the roof console box assembly.

  28. REMOVE SPOT LIGHT ASSEMBLY


    1. A01G7AWE01
      Text in Illustration
      *a Front

      Using a moulding remover, disengage the 4 claws.

    2. Disconnect the connector and remove the spot light assembly.

  29. REMOVE ASSIST GRIP SUB-ASSEMBLY

    Tech Tips

    Use the same procedure for the RH side.


    1. A01G7FKE01
      Text in Illustration
      *1 Protective Tape

      Using a screwdriver, disengage the 4 claws and remove the 2 assist grip covers.

      Note

      Do not forcibly pry the assist grip covers to prevent them from being deformed.

      Tech Tips

      Tape the screwdriver tip before use.

    2. A01G8YN

      Disengage the 2 clips and remove the assist grip sub-assembly.

    3. Remove the 2 clips from the vehicle body.

  30. REMOVE REAR ASSIST GRIP ASSEMBLY LH


    1. A01G60FE01
      Text in Illustration
      *1 Protective Tape

      Using a screwdriver, disengage the 4 claws and remove the 2 assist grip covers.

      Note

      Do not forcibly pry the assist grip covers to prevent them from being deformed.

      Tech Tips

      Tape the screwdriver tip before use.

    2. A01G66Q

      Disengage the 2 clips and remove the rear assist grip assembly LH.

    3. Remove the 2 clips from the vehicle body.

  31. REMOVE REAR ASSIST GRIP ASSEMBLY RH

    Tech Tips

    Use the same procedure as for the LH side.

  32. REMOVE VISOR BRACKET COVER (for LH Side)


    1. A01G4EI

      Using a moulding remover, disengage the 4 claws and remove the visor bracket cover.

  33. REMOVE VISOR ASSEMBLY LH


    1. A01G4KV

      Remove the 2 screws and visor assembly LH.

  34. REMOVE VISOR BRACKET COVER (for RH Side)

    Tech Tips

    Use the same procedure as for the LH side.

  35. REMOVE VISOR ASSEMBLY RH

    Tech Tips

    Use the same procedure as for the LH side.

  36. REMOVE VISOR HOLDER

    Tech Tips

    Use the same procedure for the other visor holder.


    1. A01G4K8E01

      Turn the visor holder approximately 45° and pull it out as shown in the illustration.

    2. Disengage the 2 claws and remove the visor holder.

  37. REMOVE ROOF HEADLINING ASSEMBLY (for Standard)


    1. Disconnect the connector from the inner rear view mirror assembly.

    2. w/ Rain Sensor:


      1. Disconnect the connector from the rain sensor.

    3. w/ Lane Departure Alert System:


      1. Disconnect the connector from the lane departure warning camera.

    4. Disconnect the connector from the sliding roof drive gear sub-assembly.

      A01G9IJE01
      Text in Illustration
      *A w/o Roof Antenna *B w/ Roof Antenna
      *1 Clamp *2 Fastener
      *3 Guide - -
      *a Front Pillar LH *b Front Pillar RH
      *c Rear Pillar RH *d Sliding Roof Drive Gear Sub-assembly

    5. Disengage the 3 clamps and disconnect the 3 connectors from the front pillar LH.

    6. Disengage the 2 clamps from the front pillar RH.

    7. w/o Roof Antenna:


      1. Disengage the clamp and disconnect the connector from the rear pillar RH.

    8. w/ Roof Antenna:


      1. Disengage the clamp and disconnect the 2 connectors from the rear pillar RH.

    9. Disengage the 12 claws and 11 fasteners.

    10. Slide the roof headlining assembly to disengage the 3 clips and guide as shown in the illustration.

      Tech Tips

      Leave the 3 clips in the vehicle.

    11. A01G8SN

      Remove the roof headlining assembly from the vehicle through the rear door as shown in the illustration.

      Note

      Do not damage the roof headlining assembly or body interior.

    12. A01G8I3

      Remove the 3 clips from the vehicle body as shown in the illustration.

  38. REMOVE ROOF HEADLINING ASSEMBLY (for Glass Roof)


    1. Disconnect the connector from the inner rear view mirror assembly.

    2. Disconnect the connector from the rain sensor.

    3. w/ Lane Departure Alert System:


      1. Disconnect the connector from the lane departure warning camera.

    4. Disconnect the connector from the sliding roof drive gear sub-assembly.

      A01G6AQE01
      Text in Illustration
      *1 Clamp *2 Fastener
      *3 Guide - -
      *a Front Pillar LH *b Front Pillar RH
      *c Rear Pillar RH *d Sliding Roof Drive Gear Sub-assembly

    5. Disengage the 3 clamps and disconnect the 3 connectors from the front pillar LH.

    6. Disengage the 2 clamps from the front pillar RH.

    7. Disengage the clamp and disconnect the 2 connectors from the rear pillar RH.

    8. Disengage the 12 claws and 23 fasteners.

    9. Slide the roof headlining assembly to disengage the 3 clips and guide as shown in the illustration.

      Tech Tips

      Leave the 3 clips in the vehicle.

    10. A01G7ZA

      Remove the roof headlining assembly from the vehicle through the rear door as shown in the illustration.

      Note

      Do not damage the roof headlining assembly or body interior.

    11. A01G7KZ

      Remove the 3 clips from the vehicle body as shown in the illustration.

  39. REMOVE FRONT DOOR OPENING TRIM WEATHERSTRIP LH


    1. Remove the front door opening trim weatherstrip LH.

    2. Remove the residual weatherstrip sealant from the body of the vehicle using cleaner.

      Note

      Remove the sealant completely. Any residual sealant may transfer to other areas of the vehicle when removing/installing the interior parts.

  40. REMOVE FRONT DOOR OPENING TRIM WEATHERSTRIP RH

    Tech Tips

    Use the same procedure as for the LH side.

  41. REMOVE REAR DOOR OPENING TRIM WEATHERSTRIP LH


    1. Remove the rear door opening trim weatherstrip LH.

    2. Remove the residual weatherstrip sealant from the body of the vehicle using cleaner.

      Note

      Remove the sealant completely. Any residual sealant may transfer to other areas of the vehicle when removing/installing the interior parts.

  42. REMOVE REAR DOOR OPENING TRIM WEATHERSTRIP RH

    Tech Tips

    Use the same procedure as for the LH side.