INSTRUMENT PANEL SAFETY PAD INSTALLATION


  1. INSTALL INSTRUMENT PANEL SAFETY PAD ASSEMBLY


    1. Engage the 4 guides and temporarily install the instrument panel safety pad assembly as shown in the illustration.

      A01G6IZ

      Note


      • Do not damage the instrument panel safety pad assembly.

      • Do not allow the wire harnesses to interfere with the surrounding parts.

    2. Install the 3 clips.

    3. Install the 5 bolts <C> and nut <F>.

    4. Install the 2 bolts <A>.

      Torque:
      20 N*m  { 204 kgf*cm, 15 ft.*lbf }

    5. Engage the 2 claws to connect the cooler (room temp. sensor) thermistor.

    6. Engage the claw and each clamp.

    7. Connect each connector.

  2. CONNECT NO. 2 INSTRUMENT PANEL WIRE


    1. Check that the engine switch is off.

    2. Check that the cable is disconnected from the negative (-) battery terminal.

      CAUTION:

      Wait at least 90 seconds after disconnecting the cable from the negative (-) battery terminal to disable the SRS system.

    3. A01G62B

      Connect the connector.

      Note

      When connecting any airbag connector, take care not to damage the airbag wire harness.

  3. INSTALL INSTRUMENT PANEL FINISH PANEL SUB-ASSEMBLY


    1. Engage the 8 claws to install the instrument panel finish panel sub-assembly.

  4. INSTALL NO. 1 ION GENERATOR SUB-ASSEMBLY (w/ Ion Generator)


    1. A01G4RQ

      Connect the ion generator assembly as shown in the illustration.

    2. Install the ion generator assembly with the 3 screws.

    3. Connect the connector.

    4. Engage the clamp.

  5. INSTALL FRONT NO. 3 SPEAKER ASSEMBLY


    1. Connect the connector.

    2. Install the front No. 3 speaker assembly with the 2 bolts.

      Note

      Do not touch the speaker cone.

  6. INSTALL NO. 1 SPEAKER OPENING COVER ASSEMBLY


    1. A01G94T

      Engage the 2 claws and 4 clips to install the No. 1 speaker opening cover assembly as shown in the illustration.

  7. INSTALL FRONT NO. 2 SPEAKER ASSEMBLY (for LH Side)


    1. Connect the connector.

    2. Install the front No. 2 speaker assembly with the 2 bolts.

      Note

      Do not touch the speaker cone.

      Tech Tips

      Use the same procedure for the RH side and LH side.

  8. INSTALL NO. 1 INSTRUMENT PANEL SPEAKER PANEL SUB-ASSEMBLY


    1. A01G6HV

      Engage the 3 guides as shown in the illustration.

    2. Engage the 2 clips to install the No. 1 instrument panel speaker panel sub-assembly as shown in the illustration.

  9. INSTALL FRONT PILLAR GARNISH LH


    1. Remove the protective cover.

    2. Make sure that the front pillar garnish clip is not damaged.

      Note

      If there is any damage, replace the garnish clip with a new one.

    3. A01G7ML

      Install the front pillar garnish clip to the front pillar garnish LH.

      Tech Tips

      Install the front pillar garnish clip as shown in the illustration.

    4. Engage the 2 guides as shown in the illustration.

    5. A01G6YF

      Engage the 2 clips to install the front pillar garnish LH.

  10. INSTALL FRONT NO. 2 SPEAKER ASSEMBLY (for RH Side)

    Tech Tips

    Use the same procedure as for the LH side Click here.

  11. INSTALL NO. 2 INSTRUMENT PANEL SPEAKER PANEL SUB-ASSEMBLY


    1. A01G4DK

      Engage the 3 guides as shown in the illustration.

    2. Engage the 2 clips to install the No. 2 instrument panel speaker panel sub-assembly as shown in the illustration.

  12. INSTALL FRONT PILLAR GARNISH RH

    Tech Tips

    Use the same procedure as for the LH side Click here.

  13. INSTALL NO. 3 INSTRUMENT PANEL REGISTER ASSEMBLY


    1. Engage the 4 claws, 2 clips and 2 guides to install the No. 3 instrument panel register assembly.

  14. INSTALL LOWER INSTRUMENT PANEL SUB-ASSEMBLY


    1. Connect each connector.

    2. A01G69C

      Engage the 5 claws as shown in the illustration.

    3. Install the 2 screws <E>.

    4. A01G6BL

      Open the lower instrument panel sub-assembly door as shown in the illustration.

    5. Install the lower instrument panel sub-assembly with the 3 screws <E>.

  15. INSTALL INSTRUMENT PANEL BOX DOOR COVER


    1. A01G6A8

      Engage the 4 claws to install the instrument panel box door cover as shown in the illustration.

    2. A01G83S

      Close the lower instrument panel sub-assembly door as shown in the illustration.

  16. INSTALL LOWER NO. 2 INSTRUMENT PANEL AIRBAG ASSEMBLY


    1. Check that the engine switch is off.

    2. Check that the cable is disconnected from the negative (-) battery terminal.

      CAUTION:

      Wait at least 90 seconds after disconnecting the cable from the negative (-) battery terminal to disable the SRS system.

    3. A01G5WSE01
      Text in Illustration
      *1 Airbag Connector Lock
      *2 Airbag Connector

      Connect the airbag connector to the lower No. 2 instrument panel airbag assembly.

      Note

      When connecting any airbag connector, take care not to damage the airbag wire harness.

    4. Push in the airbag connector lock to install the airbag connector.

    5. Engage the 5 claws and 2 guides to temporarily install the lower No. 2 instrument panel airbag assembly.

    6. Install the 3 bolts.

      Torque:
      10 N*m  { 102 kgf*cm, 7 ft.*lbf }

      Note

      Confirm that the lower No. 2 instrument panel airbag assembly is installed securely without any excessive gaps and is not protruding outward.

  17. INSTALL NO. 2 INSTRUMENT PANEL UNDER COVER SUB-ASSEMBLY


    1. Connect the connector.

    2. A01G4TS

      Engage the 2 guides, claw and 4 clips to install the No. 2 instrument panel under cover sub-assembly as shown in the illustration.

  18. INSTALL INSTRUMENT SIDE PANEL RH


    1. A01G5BG

      Engage the 2 guides as shown in the illustration.

    2. A01G9H5

      Engage the 2 claws and 4 clips to install the instrument side panel RH as shown in the illustration.

  19. INSTALL FRONT DOOR OPENING TRIM COVER RH

    Tech Tips

    Use the same procedure as for the LH side Click here.

  20. INSTALL COWL SIDE TRIM BOARD RH

    Tech Tips

    Use the same procedure as for the LH side Click here.

  21. INSTALL FRONT DOOR SCUFF PLATE RH

    Tech Tips

    Use the same procedure as for the LH side Click here.

  22. INSTALL REAR CONSOLE BOX ASSEMBLY

    Click here

  23. INSTALL MULTI-DISPLAY ASSEMBLY


    1. Connect each connector and engage the 2 clips.

    2. Install the multi-display assembly with the 2 screws.

  24. INSTALL CENTER INSTRUMENT CLUSTER FINISH PANEL SUB-ASSEMBLY


    1. A01G4JL

      Engage the 2 clips and 5 guides as shown in the illustration.

    2. Install the center instrument cluster finish panel sub-assembly with the 2 clips.

  25. INSTALL SWITCH BASE


    1. for LHD:


      1. Connect the connector.

      2. Engage the 3 claws to install the switch base.

    2. for RHD:


      1. Connect the connector.

      2. Engage the 4 claws to install the switch base.

  26. INSTALL NO. 1 INSTRUMENT PANEL REGISTER ASSEMBLY


    1. Engage the 6 claws and 2 guides to install the No. 1 instrument panel register assembly.

  27. INSTALL NO. 1 SWITCH HOLE BASE


    1. Connect each connector.

    2. Engage the 4 claws to install the No. 1 switch hole base.

  28. INSTALL COMBINATION METER ASSEMBLY


    1. Connect the 2 connectors.

    2. Engage the 2 clips.

    3. Install the combination meter assembly with the 2 screws.

  29. INSTALL LOWER NO. 1 INSTRUMENT PANEL FINISH PANEL


    1. for LHD:


      1. Connect each connector and engage each clamp.

      2. Engage the 12 claws, 2 clips and guide.

      3. Install the lower No. 1 instrument panel finish panel with the 2 bolts <B>.

    2. for RHD:


      1. Connect each connector and engage each clamp.

      2. Engage the 6 claws, 3 clips and guide.

      3. Install the lower No. 1 instrument panel finish panel with the 2 bolts <B>.

      4. A01G7GC

        Engage the 2 claws to close the cover as shown in the illustration.

  30. CONNECT HOOD LOCK CONTROL LEVER SUB-ASSEMBLY


    1. Engage the claw and 2 guides to connect the hood lock control lever sub-assembly.

  31. INSTALL INSTRUMENT SIDE PANEL LH


    1. A01G990

      Engage the 2 guides as shown in the illustration.

    2. A01G8LE

      Engage the 2 claws and 4 clips to install the instrument side panel LH as shown in the illustration.

  32. INSTALL FRONT DOOR OPENING TRIM COVER LH


    1. Engage the guide.

    2. Engage the 3 claws to install the front door opening trim cover LH.

  33. INSTALL COWL SIDE TRIM BOARD LH


    1. Engage the clip and claw.

    2. Install the cowl side trim board LH with the clip.

  34. INSTALL FRONT DOOR SCUFF PLATE LH


    1. Engage the 10 claws to install the front door scuff plate LH.

  35. INSTALL RADIO RECEIVER ASSEMBLY WITH BRACKET (w/o Navigation System)


    1. Connect each connector.

    2. Engage the 2 clips and 2 claws to temporarily install the radio receiver assembly with bracket.

    3. Install the radio receiver assembly with bracket with the 4 bolts.

  36. INSTALL MULTI-MEDIA MODULE RECEIVER ASSEMBLY WITH BRACKET (w/ Navigation System)


    1. Connect each connector.

    2. Engage the 2 clips and 2 claws to the vehicle body to temporarily install the multi-media module receiver assembly with bracket.

    3. Install the multi-media module receiver assembly with bracket with the 4 bolts.

  37. INSTALL LOWER CENTER INSTRUMENT PANEL FINISH PANEL


    1. A01G96C

      Engage the 2 claws and 5 clips to install the lower center instrument panel finish panel as shown in the illustration.

  38. INSTALL NO. 2 INSTRUMENT PANEL REGISTER ASSEMBLY


    1. Connect the connector.

    2. Engage the 11 claws and clip to install the No. 2 instrument panel register assembly.

      A01G5L1

      Note

      When installing the No. 2 instrument panel register assembly, check that the wire harness is not caught between the No. 2 instrument panel register assembly and duct.

  39. INSTALL CENTER INSTRUMENT CLUSTER FINISH PANEL GARNISH


    1. Connect the connector.

    2. Engage the 10 claws and 2 clips to install the center instrument cluster finish panel garnish.

      A01G9I0

  40. INSTALL INSTRUMENT CLUSTER FINISH PANEL SUB-ASSEMBLY


    1. Connect the connector.

    2. A01G4Z0

      Engage the 5 claws and 2 guides as shown in the illustration.

    3. Install the instrument cluster finish panel sub-assembly with the 2 screws <E>.

  41. INSTALL TURN SIGNAL SWITCH ASSEMBLY WITH SPIRAL CABLE SUB-ASSEMBLY

    Note


    • Do not replace the spiral cable with sensor sub-assembly with the battery connected and the engine switch on (IG).

    • Do not rotate the spiral cable with sensor sub-assembly without the steering wheel with the battery connected and the engine switch on (IG).

    • Ensure that the steering wheel is installed and aligned straight when inspecting the steering sensor.


    1. Engage the 3 claws to install the turn signal switch assembly with spiral cable sub-assembly to the steering post assembly.

    2. Connect the connectors to the turn signal switch assembly with spiral cable sub-assembly.

  42. INSTALL UPPER STEERING COLUMN COVER


    1. Engage the 2 claws to install the upper steering column cover.

    2. Engage the 4 clips and 2 guides to the upper steering column cover.

  43. INSTALL LOWER STEERING COLUMN COVER (for Manual Tilt and Manual Telescopic Steering Column)


    1. A01G4YC

      Engage the 2 claws to install the lower steering column cover.

    2. A01G68E

      Install the 2 screws.

      Torque:
      2.0 N*m  { 20 kgf*cm, 18 in.*lbf }
    3. A01G7G8

      Engage the claw.

  44. INSTALL LOWER STEERING COLUMN COVER (for Power Tilt and Power Telescopic Steering Column)


    1. A01G6SZ

      Engage the 2 claws to install the lower steering column cover.

    2. A01G60O

      Install the 3 screws.

      Torque:
      2.0 N*m  { 20 kgf*cm, 18 in.*lbf }

  45. INSTALL STEERING WHEEL ASSEMBLY


    1. A01G4KOE01
      Text in Illustration
      *a Matchmark

      Install the steering wheel assembly aligning the matchmarks on the steering wheel assembly and steering main shaft.

    2. Install the steering wheel assembly set nut.

      Torque:
      50 N*m  { 510 kgf*cm, 37 ft.*lbf }

    3. w/ Steering Heater:


      1. A01G5HW

        Connect the connector.

    4. Connect the connectors to the spiral cable sub-assembly.

  46. INSTALL HORN BUTTON ASSEMBLY

    Click here

  47. CONNECT CABLE TO NEGATIVE BATTERY TERMINAL

    Note

    When disconnecting the cable, some systems need to be initialized after the cable is reconnected Click here.


    1. for Power Tilt and Power Telescopic Steering Column:


      1. Reset the auto away/return function setting to the previous condition by changing the customize parameter Click here.

  48. INSPECT SRS WARNING LIGHT

    Click here