REAR SUNSHADE SYSTEM Rear Sunshade Shift-linked Function does not Operate when Shift Lever is Moved to R Position

DESCRIPTION

When the engine switch is on (IG) and the shift lever is moved to R, the shift position sensors send a reverse (R) signal to the ECM. Then, the ECM sends this signal to the main body ECU (multiplex network body ECU) via CAN. When the rear sunshade relay receives this signal with the rear sunshade raised, the rear sunshade is lowered.

WIRING DIAGRAM

A01G5NQE18

INSPECTION PROCEDURE

Note


  • Since the rear sunshade system has functions that use CAN communication, first confirm that there is no malfunction in the CAN communication system using the How to Proceed with Troubleshooting procedure Click here.

  • If the main body ECU (multiplex network body ECU) is replaced, refer to Service Bulletin.

PROCEDURE


  1. READ VALUE USING GTS


    1. Connect the GTS to the DLC3.

    2. Turn the engine switch on (IG).

    3. Turn the GTS on.

    4. Enter the following menus: Powertrain / Engine / Data List.

    5. Read the Data List according to the display on the GTS.

      Engine
      Tester Display Measurement Item/Range Normal Condition Diagnostic Note
      Shift SW Status (R Range) PNP switch status / ON or OFF

      ON: Shift lever in R

      OFF: Shift lever not in R

      		 When the shift lever position displayed on the GTS differs from the actual position, adjustment of the PNP switch or the shift cable may be incorrect.
      OK
      The GTS display changes according to the shift position selected using the shift lever.
      Result
      Result Proceed to
      OK A
      NG (for 2GR-FE) B
      NG (for 2AR-FE) C

    B

    GO TO SFI SYSTEM Click here

    C

    GO TO SFI SYSTEM Click here

    A

  2. PERFORM ACTIVE TEST USING GTS


    1. Connect the GTS to the DLC3.

    2. Turn the engine switch on (IG).

    3. Turn the GTS on.

    4. Enter the following menus: Body Electrical / Main Body / Active Test.

    5. Perform the Active Test according to the display on the GTS.

      Tech Tips

      Make sure the rear window shade assembly is raised before performing Active Test.

      Main Body
      Tester Display Test Part Control Range Diagnostic Note
      Reverse Gear Signal Reverse signal OFF/ON -
      OK
      The rear window shade assembly is lowered.

    NG

    CHECK HARNESS AND CONNECTOR (REVERSE SIGNAL) Click here

    OK

    REPLACE MAIN BODY ECU (MULTIPLEX NETWORK BODY ECU) Click here

  3. CHECK HARNESS AND CONNECTOR (REVERSE SIGNAL)


    1. Disconnect the P11 rear sunshade relay connector.

    2. Measure the voltage according to the value(s) in the table below.

      Standard Voltage
      Tester Connection Condition Specified Condition
      P11-3 (REV) - Body ground Always 11 to 14 V

    NG

    CHECK HARNESS AND CONNECTOR (REAR SUNSHADE RELAY - MAIN BODY ECU (MULTIPLEX NETWORK BODY ECU)) Click here

    OK

    REPLACE REAR SUNSHADE RELAY Click here

  4. CHECK HARNESS AND CONNECTOR (REAR SUNSHADE RELAY - MAIN BODY ECU (MULTIPLEX NETWORK BODY ECU))


    1. Disconnect the H10 main body ECU (multiplex network body ECU) connectors.

    2. Measure the resistance according to the value(s) in the table below.

      Standard Resistance
      Tester Connection Condition Specified Condition
      P11-3 (REV) - H10-15 (REV) Always Below 1 Ω
      H10-15 (REV) - Body ground Always 10 kΩ or higher

    NG

    REPAIR OR REPLACE HARNESS OR CONNECTOR

    OK

    REPLACE MAIN BODY ECU (MULTIPLEX NETWORK BODY ECU) Click here