FRONT SEATBACK HEATER INSTALLATION

Tech Tips


  • Use the same procedure for the RH side and LH side.

  • The following procedure is for the LH side.


  1. INSTALL FRONT SEATBACK HEATER (SEPARATE TYPE FRONT SEATBACK COVER)


    1. A01G91F

      Using hog ring pliers, install the front seatback heater (separate type front seatback cover) to the separate type front seatback pad with 14 new hog rings.

      Note


      • Be careful not to damage the front seatback heater (separate type front seatback cover).

      • When installing the hog rings, take care to minimize wrinkles as much as possible.

  2. INSTALL SEPARATE TYPE FRONT SEATBACK COVER WITH PAD


    1. Temporarily install the separate type front seatback cover with pad.

    2. Engage each claw to install the 2 front seat headrest supports.

    3. Install the 3 brackets with the 2 nuts.

      Torque:
      5.5 N*m  { 56 kgf*cm, 49 in.*lbf }

      CAUTION:


      • For vehicles with a front seat airbag assembly, the separate type front seatback cover must be securely installed. Otherwise, the front seat airbag assembly may not deploy properly.

      • Make sure that the strap is not twisted after installing the nut.

      • Install the brackets securely.

    4. A01G5BV

      Using hog ring pliers, install 2 new hog rings.

      Note


      • Be careful not to damage the separate type front seatback cover.

      • When installing the hog rings, take care to minimize wrinkles as much as possible.

    5. Engage each hook.

    6. A01G47V

      Using hog ring pliers, install 2 new hog rings.

      Note


      • Be careful not to damage the separate type front seatback cover.

      • When installing the hog rings, take care to minimize wrinkles as much as possible.

    7. Engage the claw and 2 clamps to install the front seat airbag assembly wire harness.

  3. CONNECT CONNECTOR


    1. Engage the clamp.

    2. Connect the connector.

  4. INSTALL SEATBACK CLIMATE CONTROL COVER (w/ Climate Control Seat System)


    1. Install the seatback climate control cover with the 4 screws.

  5. INSTALL FRONT SEATBACK BOARD SUB-ASSEMBLY


    1. Engage the 2 hooks to install the front seatback board sub-assembly.

    2. Install the 2 screws.

  6. INSTALL FRONT SEAT CUSHION SHIELD


    1. Engage the 3 claws and 5 guides to install the front seat cushion shield.

    2. Install the 2 screws.

  7. INSTALL FRONT POWER ADJUSTER SHIELD


    1. Connect the connector to the front lumbar power seat switch.

    2. w/o Seat Position Memory System:


      1. Connect the connector to the front power seat switch.

    3. w/ Seat Position Memory System:


      1. Connect the 2 connectors to the front power seat switch.

    4. w/ Variable Seat Cushion System:


      1. Connect the connector to the seat variable cushion switch.

    5. Engage the 2 claws to install the front power adjuster shield.

    6. Install the 2 screws.

  8. INSTALL FRONT INNER NO. 1 SEAT CUSHION SHIELD


    1. Engage the 2 claws and 2 clips to install the front inner No. 1 seat cushion shield.

    2. Install the 2 screws.

  9. INSTALL FRONT SEAT INNER CUSHION SHIELD


    1. Engage the 3 claws and 4 guides to install the front seat inner cushion shield.

    2. Install the screw.

    3. Install the clip.

  10. CONNECT FRONT SEATBACK BOARD SUB-ASSEMBLY (w/o Foot Light)


    1. Connect the rubber band of the front seatback board sub-assembly to the front seat adjuster assembly.

  11. CONNECT FRONT SEATBACK BOARD SUB-ASSEMBLY (w/ Foot Light)


    1. for Driver Side:


      1. Connect the connector.

      2. Engage the 2 clamps.

    2. for Front Passenger Side:


      1. Connect the connector.

      2. Engage the clamp.

    3. Engage the 2 fasteners.

    4. Connect the rubber band of the front seatback board sub-assembly to the front seat adjuster assembly.

  12. INSTALL POWER SEAT SWITCH ASSEMBLY (for Front Passenger Side with Power Seat Switch Assembly)


    1. Connect the connector to the power seat switch assembly.

    2. Engage the 2 claws to install the power seat switch assembly to the front seat assembly RH.

  13. INSTALL FRONT SEAT ASSEMBLY

    Click here