BLACK OUT TAPE(for Rear Door) INSTALLATION

CAUTION / NOTICE / HINT

PROCEDURE

1. Click here

   PRECAUTION

   Note:

   After turning the power switch off, waiting time may be required before disconnecting the cable from the auxiliary battery negative (-) terminal. Therefore, make sure to read the disconnecting the cable from the auxiliary battery negative (-) terminal notices before proceeding with work (Click here).

2. Click here

   REPAIR INSTRUCTION

   Click here

3. Click here

   INSTALL FRONT INNER BLACK OUT TAPE

   
   
   1. 

      Refer to the illustration to position a new front inner black out tape.

      Table 1. Text in Illustration

      *A	LH Side	*B	RH Side
      *a	Edge of Curved Surface	*b	Straight
      *c	Triangle	-	-

      Table 2. Standard Measurement

      Dimension	Measurement
      A	1.5 mm (0.0591 in.)
      B	1.0 mm (0.0394 in.)

   2. Remove the release paper and apply the front inner black out tape.

4. Click here

   INSTALL REAR INNER BLACK OUT TAPE

   
   
   1. 

      Refer to the illustration to position a new rear inner black out tape.

      Table 3. Text in Illustration

      *A	LH Side	*B	RH Side
      *a	Edge of Curved Surface	*b	Straight
      *c	Triangle	-	-

      Table 4. Standard Measurement

      Dimension	Measurement
      A	1.5 mm (0.0591 in.)
      B	1.0 mm (0.0394 in.)

   2. Remove the release paper and apply the rear inner black out tape.

5. Click here

   INSTALL CURTAIN HOOK (w/ Rear Door Sunshade)

   Click here

6. Click here

   INSTALL REAR DOOR FRAME GARNISH

   Click here

7. Click here

   INSTALL REAR DOOR GLASS ASSEMBLY

   Click here

8. Click here

   INSTALL REAR DOOR QUARTER WINDOW GLASS

   Click here

9. Click here

   INSTALL REAR DOOR LOWER WINDOW FRAME SUB-ASSEMBLY

   Click here

10. Click here

    INSTALL REAR DOOR NO. 1 VENT SEAL

    Click here

11. Click here

    INSTALL REAR DOOR GLASS RUN

    Click here

12. Click here

    CONNECT REAR DOOR WEATHERSTRIP

    Click here

13. Click here

    INSTALL REAR DOOR SERVICE HOLE COVER

    Click here

14. Click here

    INSTALL REAR DOOR ARMREST SET BRACKET

    Click here

15. Click here

    INSTALL REAR DOOR INNER GLASS WEATHERSTRIP

    Click here

16. Click here

    INSTALL REAR SIDE CURTAIN ASSEMBLY (w/ Rear Door Sunshade)

    Click here

17. Click here

    INSTALL REAR DOOR TRIM BOARD SUB-ASSEMBLY

    Click here

18. Click here

    INSTALL COURTESY LIGHT ASSEMBLY

    Click here

19. Click here

    INSTALL REAR DOOR NO. 1 STIFFENER CUSHION

    Click here

20. Click here

    INSTALL DOOR PULL HANDLE COVER

    Click here

21. Click here

    INSTALL REAR POWER WINDOW REGULATOR SWITCH ASSEMBLY WITH REAR DOOR ARMREST BASE PANEL

    Click here

22. Click here

    INSTALL REAR DOOR INSIDE HANDLE BEZEL PLUG

    Click here

23. Click here

    CONNECT CABLE TO NEGATIVE AUXILIARY BATTERY TERMINAL

    Note:

    When disconnecting the cable, some systems need to be initialized after the cable is reconnected (Click here).

24. Click here

    INSTALL LUGGAGE TRIM SERVICE HOLE COVER

    Click here

25. Click here

    INITIALIZE POWER WINDOW CONTROL SYSTEM

    (Click here)

26. Click here

    INSPECT POWER WINDOW OPERATION

    (Click here)