REAR BUMPER REASSEMBLY

PROCEDURE


  1. INSTALL NO. 1 REAR BUMPER REINFORCEMENT


    1. A0008IQ

      Install the No. 1 rear bumper reinforcement with the 6 nuts.

      Torque:
      35 N*m  { 357 kgf*cm, 26 ft.*lbf }

  2. INSTALL REAR BUMPER ENERGY ABSORBER


    1. A0009DK

      Engage the 2 guides to install the rear bumper energy absorber.

  3. INSTALL NO. 1 REAR BUMPER SIDE SUPPORT LH


    1. A0004BH

      Engage the 2 guides and claw.

    2. A0004C7

      Install the screw.

    3. A0007IC

      Install the screw.

    4. A00097I

      Install the No. 1 rear bumper side support LH with the 2 grommets.

  4. INSTALL NO. 1 REAR BUMPER SIDE SUPPORT RH

    Tech Tips

    Use the same procedure as for the LH side.

  5. INSTALL NO. 2 REAR BUMPER SIDE SUPPORT LH


    1. A0003H1

      Engage the 5 claws.

    2. A0006MT

      Engage the 4 clips to install the No. 2 rear bumper side support LH as shown in the illustration.

  6. INSTALL NO. 2 REAR BUMPER SIDE SUPPORT RH

    Tech Tips

    Use the same procedure as for the LH side.

  7. INSTALL LOWER REAR BUMPER RETAINER


    1. A0004M3

      Engage the 10 claws.

    2. A0006EN

      Install the lower rear bumper retainer with the 2 screws.

  8. INSTALL NO. 3 ULTRASONIC SENSOR CLIP (w/ LEXUS Parking Assist-sensor System)

    Tech Tips

    When installing the No. 3 ultrasonic sensor clip, heat the rear bumper assembly using a heat light.

    Heating Temperature
    Item Temperature
    Rear Bumper Assembly 20 to 30°C (68 to 86°F)

    Note

    Do not heat the front bumper assembly excessively.


    1. Clean the rear bumper assembly surface.


      1. Using a heat light, heat the rear bumper assembly surface.

      2. Remove the double-sided tape from the rear bumper assembly.

      3. Wipe off any tape adhesive residue with cleaner.

    2. Install the No. 3 ultrasonic sensor clip.


      1. A0007PQE01
        Text in Illustration
        *a Line

        Coat the installation surface on the rear bumper assembly with primer as shown in the illustration.

      2. Remove the release paper from a new No. 3 ultrasonic sensor clip.

        Tech Tips

        After removing the release paper, keep the exposed adhesive free from foreign matter.

      3. A0006NPE01
        Text in Illustration
        *a Line

        Install a new No. 3 ultrasonic sensor clip.

        Note


        • Make sure that the No. 3 ultrasonic sensor clip are installed in the line as shown in the illustration.

        • Allow the primer to dry for 10 minutes or more.

        • If 24 hours have elapsed since primer was applied, reapply primer

      4. Lightly press the surface of the No. 3 ultrasonic sensor clip to ensure a close fit.

  9. INSTALL NO. 2 LUGGAGE ROOM WIRE (w/ LEXUS Parking Assist-sensor System)


    1. A0008ZM

      Engage the clamp to install the No. 2 luggage room wire.

  10. INSTALL NO. 2 ULTRASONIC SENSOR RETAINER (w/ LEXUS Parking Assist-sensor System)

    Click here

  11. INSTALL NO. 2 ULTRASONIC SENSOR WITH CLIP (w/ LEXUS Parking Assist-sensor System)

    Click here

  12. INSTALL REFLEX REFLECTOR ASSEMBLY LH


    1. A00048V

      Engage the claw.

    2. Install the reflex reflector assembly LH with the screw.

  13. INSTALL REFLEX REFLECTOR ASSEMBLY RH

    Tech Tips

    Use the same procedure as for the LH side.

  14. INSTALL REAR BUMPER PAD RH


    1. Wipe off any tape adhesive residue with cleaner.

    2. A0008CI

      Install a new rear bumper pad RH.

      Tech Tips

      Stick the new rear bumper pad RH on the line marked on the rear bumper assembly.

  15. INSTALL REAR BUMPER PAD LH


    1. Wipe off any tape adhesive residue with cleaner.

    2. A0008CI

      Install a new rear bumper pad LH.

      Tech Tips

      Stick the new rear bumper pad LH on the line marked on the rear bumper assembly.