FRONT WIPER MOTOR INSTALLATION

PROCEDURE

1. Click here

   INSTALL WINDSHIELD WIPER MOTOR ASSEMBLY

   
   

   1. Using a T30 "TORX" socket wrench, install the windshield wiper motor assembly with 2 bolts.

      7.5 N*m

      76 kgf*cm

      66 in.*lbf

   2. 

      Apply MP grease to the pivot of the windshield wiper motor assembly.

      Table 1. Text in Illustration

      *a	Pivot of the windshield wiper motor assembly

   3. 

      Connect the windshield wiper link No. 1 rod to the pivot of the windshield wiper motor assembly.

      Table 2. Text in Illustration

      *1	Windshield Wiper Link No. 1 Rod
      *a	Pivot of the windshield wiper motor assembly

2. Click here

   INSTALL WINDSHIELD WIPER MOTOR AND LINK ASSEMBLY

   
   
   1. 

      Engage the motor grommet as shown in the illustration.

      Table 3. Text in Illustration

      *1	Motor Grommet

      Note:

      Be careful not to damage the windshield when installing the windshield wiper motor and link assembly.

   2. Install the windshield wiper motor and link assembly with the 2 bolts.

      7.5 N*m

      76 kgf*cm

      66 in.*lbf

   3. Connect the connector.

3. Click here

   INSTALL COWL TOP VENTILATOR LOUVER SUB-ASSEMBLY

   
   
   1. 

      Engage the 8 guides as shown in the illustration.

   2. 

      Engage the 6 claws and guide to install the cowl top ventilator louver sub-assembly.

   3. Engage the claw and connect the windshield outside moulding LH.

   4. Engage the claw and connect the windshield outside moulding RH.

4. Click here

   INSTALL FRONT WIPER ARM AND BLADE ASSEMBLY LH

   
   

   1. When reusing the front wiper arm and blade assembly LH:

      
      
      1. 

         Clean the wiper arm serrations to remove any burrs, dirt, etc.

         Table 4. Text in Illustration

         *1	Wiper Arm Serration
         *2	Wiper Pivot Serration

         Note:

         Do not grind down the wiper arm serrations.

   2. When reusing the windshield wiper link assembly:

      
      

      1. Clean the wiper pivot serrations with a wire brush.

   3. Operate the wiper and stop the windshield wiper motor assembly at the automatic stop position.

   4. 

      Install the front wiper arm and blade assembly LH with the nut to the position shown in the illustration.

      22 N*m

      224 kgf*cm

      16 ft.*lbf

      Table 5. Text in Illustration

      *1	Ceramic Dot

      Tip:

      Hold the wiper arm by hand while tightening the nut.

5. Click here

   INSTALL FRONT WIPER ARM AND BLADE ASSEMBLY RH

   
   

   1. When reusing the front wiper arm and blade assembly RH:

      
      
      1. 

         Clean the wiper arm serrations to remove any burrs, dirt, etc.

         Table 6. Text in Illustration

         *1	Wiper Arm Serration
         *2	Wiper Pivot Serration

         Note:

         Do not grind down the wiper arm serrations.

   2. When reusing the windshield wiper link assembly:

      
      

      1. Clean the wiper pivot serrations with a wire brush.

   3. Operate the wiper and stop the windshield wiper motor assembly at the automatic stop position.

   4. 

      Install the front wiper arm and blade assembly RH with the nut to the position shown in the illustration.

      22 N*m

      224 kgf*cm

      16 ft.*lbf

      Table 7. Text in Illustration

      *1	Ceramic Dot

      Tip:

      Hold the wiper arm by hand while tightening the nut.

   5. Turn the power switch on (IG).

   6. Operate the front wiper while spraying washer fluid onto the windshield glass. Make sure that the front wiper functions properly and the wiper does not come into contact with the vehicle body.

   7. Lift each wiper arm twice after the wipers stop and check the wiper set position.

   8. Turn the power switch off.